Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255072 CYLINDER BLOCK A

1VD-FTV ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

Before performing these installation procedures, sufficiently clean and remove any foreign matter from the cylinder block, connecting rod and other parts.


PROCEDURE

Hide 11432U 1.INSTALL CYLINDER BLOCK STRAIGHT SCREW PLUG

a.
A177329E02
2.735,1.382 3.094,1.541 0.359,0.160 10 Front 0.409,3.152 0.768,3.311 0.359,0.160 10 Front 2.436,3.693 3.225,3.855 0.790,0.162 10 New Gasket 2.386,3.784 2.269,3.784 2.269,3.784 2.201,4.004 false

Install 2 new gaskets and the 2 straight screw plugs.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A164571

Using a 5 mm hexagon wrench, install the 4 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101A 3.INSTALL PISTON PIN HOLE SNAP RING

a.
A182756E01
1.948,1.542 2.912,1.696 0.964,0.154 10 Cutout Position

Using a screwdriver, install a new snap ring on one side of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13101 4.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A164822E01
0.113,0.051 0.470,0.220 0.357,0.169 10 80°C

Gradually heat the piston to approximately 80°C (176°F).


b.

Coat the piston pin with engine oil.


c.
A181687E01
0.695,4.278 1.408,4.440 0.714,0.162 10 Front Mark

RH:

i.

Align the front marks of the piston and connecting rod, and push in the piston pin with your thumb.

HINT:
·

The piston and pin are a matched set.

·

The piston has 2 front marks.





d.
A182755E01
0.655,4.242 1.374,4.404 0.718,0.162 10 Front Mark

LH:

i.

Face the front marks of the piston and connecting rod in opposite directions, and push in the piston pin with your thumb.

HINT:
·

The piston and pin are a matched set.

·

The piston has 1 front mark.





e.
A164623

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


Hide 5.INSTALL PISTON PIN HOLE SNAP RING

a.
A182757E01
0.214,1.683 1.187,1.830 0.973,0.147 10 Cutout Position

Using a screwdriver, install a new snap ring at the other end of the piston pin hole.

HINT:

Be sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



Hide 13011 6.INSTALL PISTON RING SET

a.
A164800

Install the oil ring expander by hand.


b.

Using a piston ring expander, install the oil ring.

HINT:

Align the oil ring ends and coil joint as shown in the illustration.


A385760E01
3.365,2.26 3.365,1.604 3.365,1.604 3.688,1.521 false 4.198,1.438 4.458,1.438 4.458,1.438 4.458,0.813 false 2.938,2.333 4.271,2.531 1.333,0.198 10 false Oil Ring Expander 4.167,0.552 4.781,0.76 0.615,0.208 10 false Oil Ring 5.583,0.917 6.198,1.125 0.615,0.208 10 false Coil Joint 5.438,2.385 6.385,2.604 0.948,0.219 10 false Oil Ring Ends


c.

Using a piston ring expander, install the No. 1 and No. 2 compression rings so that the code marks are positioned as shown in the illustration.

A309378E01
5.97,0.074 6.729,0.223 0.758,0.149 10 Code Mark 3.62,1.902 4.871,2.236 1.250,0.334 10 No. 1 Compression Ring 5.344,1.902 6.594,2.236 1.250,0.334 10 No. 2 Compression Ring 5.931,0.143 5.803,0.143 5.803,0.143 5.625,0.786 false

HINT:
·

Install the No. 1 compression ring with no code mark. The compression ring can be installed with either side facing upward.

·

Install the No. 2 compression ring with the code mark shown in the table below facing upward.



Standard Code Mark:
Item Code Mark
(w/ EGR System)
Code Mark
(w/o EGR System)
No. 1 compression ring No mark No mark
No. 2 compression ring T2 2T



d.

Position the piston rings so that the ring ends are as shown in the illustration.

A385761E01
3.156,3.031 3.156,2.625 3.156,2.625 3.531,2.083 true 0.563,3.031 0.563,2.208 0.563,2.208 0.938,2.083 true 0.563,2.198 0.938,1.865 true 0.177,0.344 1.073,0.594 0.896,0.25 12 false for Bank 1: 3.052,0.323 3.948,0.573 0.896,0.25 12 false for Bank 2: 0.313,3.104 1.208,3.354 0.896,0.25 10 false Front Mark 2.917,3.104 3.813,3.354 0.896,0.25 10 false Front Mark 5.563,1.188 7.104,1.375 1.542,0.188 10 false No. 1 Compression Ring 5.563,1.656 7.104,1.844 1.542,0.188 10 false No. 2 Compression Ring 5.573,2.125 6.146,2.313 0.573,0.188 10 false Oil Ring 5.583,2.604 6.781,2.802 1.198,0.198 10 false Oil Ring Expander 5.354,1.177 5.563,1.365 0.208,0.188 10 false A 0.813,1.177 1.021,1.365 0.208,0.188 10 false A 4.813,2.573 5.021,2.76 0.208,0.188 10 false A 5.354,1.656 5.563,1.844 0.208,0.188 10 false B 2.229,2.573 2.438,2.76 0.208,0.188 10 false B 3.396,1.177 3.604,1.365 0.208,0.188 10 false B 5.344,2.115 5.552,2.302 0.208,0.188 10 false C 0.802,2.573 1.01,2.76 0.208,0.188 10 false C 4.802,1.188 5.01,1.375 0.208,0.188 10 false C 5.354,2.594 5.563,2.781 0.208,0.188 10 false D 3.385,2.573 3.594,2.76 0.208,0.188 10 false D 2.229,1.177 2.438,1.365 0.208,0.188 10 false D


Hide 13041 7.INSTALL CONNECTING ROD BEARING

a.
U162925E02
0.625,0.51 0.625,1.188 true 2.219,1.448 2.104,1.323 2.104,1.323 1.938,1.323 false 0.469,1.208 0.792,1.365 0.323,0.156 10 false Claw 1.583,1.24 1.906,1.396 0.323,0.156 10 false Claw

Align the bearing claw with the claw groove of the connecting rod cap.

NOTICE:
·

Clean the contact surface of the bearing and connecting rod cap.

·

Do not apply engine oil to the bearing and its contact surface.




b.

Align the bearing claw with the claw groove of the connecting rod.

NOTICE:
·

Clean the contact surface of the bearing and connecting rod.

·

Do not apply engine oil to the bearing and its contact surface.




Hide 11711 8.INSTALL CRANKSHAFT BEARING

NOTICE:

Be sure to install the selected bearing.


HINT:

Main bearings come in widths of 20.5 mm (0.807 in.) and 22.5 mm (0.886 in.).

A385764E01
0.302,0.969 1.365,1.396 1.063,0.427 10 false No. 1 and 5 Journal Bearings 4.719,0.958 5.781,1.385 1.063,0.427 10 false No. 2, 3 and 5 Journal Bearings 1.031,1.854 1.708,2.063 0.677,0.208 10 false 22.5 mm 5.448,1.865 6.125,2.073 0.677,0.208 10 false 20.5 mm


Bearing Width
Item Standard Width
No. 1 and 5 journal bearings 22.5 mm (0.886 in.)
No. 2, 3 and 4 journal bearings 20.5 mm (0.807 in.)

a.

Clean each main journal and bearing.


b.
A164628

Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper crankshaft bearings.

NOTICE:
·

Clean the contact surface of the bearing and cylinder block.

·

Do not apply engine oil to the bearing and its contact surface.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.




c.
A164629

Align the bearing claw with the claw groove of the bearing cap, and push in the 5 lower crankshaft bearings.

NOTICE:
·

Clean the contact surface of the bearing and crankshaft bearing cap.

·

Do not apply engine oil to the bearing and its contact surface.



HINT:

The number marked on each bearing cap indicates the installation position.



Hide 13411 9.INSTALL CRANKSHAFT

NOTICE:

Clean the contact surface of each main journal and crank pin.


a.
A164570

Apply new engine oil to the upper crankshaft bearing and install the crankshaft to the cylinder block.


b.
A164600E04
1.219,1.063 0.594,1.063 0.594,1.063 0.594,1.781 true 1.979,1.417 0.594,1.417 true 0.25,1.802 1.323,2.125 1.073,0.323 10 true Oil Groove

Push the crankshaft toward the rear thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the front of the engine.


c.

Push the crankshaft toward the forward thrust direction to create clearance, and install a thrust washer to the No. 3 journal position with the oil groove facing the rear of the engine.


d.
A164632E01
0.108,1.082 0.477,1.240 0.368,0.158 10 Front

Examine the front marks and numbers and install the bearing caps to the cylinder block.


e.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.


f.

Temporarily install the crankshaft bearing cap bolts labeled A or the bolts labeled B.

A385765E01
1.74,0.729 1.563,0.729 1.563,0.729 1.156,0.583 true 1.813,0.646 2.313,0.813 0.5,0.167 10 false Spacer 0.948,0.854 1.406,1.031 0.458,0.177 10 false 8 mm 4.76,0.906 5.906,1.083 1.146,0.177 10 false 106 mm (4.17 in.) 4.667,2.167 5.875,2.344 1.208,0.177 10 false 90.5 mm (3.56 in.) 6.135,0.427 6.635,0.604 0.5,0.177 10 false 11 mm 6.104,0.604 6.74,0.792 0.635,0.188 10 false (0.433 in.) 6.052,1.667 6.531,1.854 0.479,0.188 10 false 10 mm 6.031,1.844 6.708,2.063 0.677,0.219 10 false (0.394 in.) 4.031,0.5 4.219,0.677 0.188,0.177 10 false A 4.042,1.75 4.229,1.927 0.188,0.177 10 false B

HINT:

In place of the cylinder block stiffening plates, install 8 mm (0.315 in.) thick spacers to the crankshaft bearing cap bolts.

Standard Length
Item Diameter Length
A 11 mm (0.433 in.) 106 mm (4.17 in.)
B 10 mm (0.394 in.) 90.5 mm (3.56 in.)



g.

Uniformly tighten the 2 crankshaft bearing cap bolts for each bearing cap in several passes to ensure a proper fit.

NOTICE:

Do not tap the bearing cap with a plastic-faced hammer.



h.

Remove the crankshaft bearing cap bolts and spacers.


i.
U162923E02
2.594,0.531 1.75,0.115 1.75,0.115 2.646,1.521 true 1.5,0.115 1.74,0.115 false 0.781,0.031 1.906,0.281 1.125,0.25 10 true Front Mark

Set the 2 cylinder block stiffening plates on the cylinder block.

HINT:

Make sure the arrows on the stiffening plates face the engine front.



j.
U163108E02
1.365,2.646 1.521,2.813 0.156,0.167 10 false A 1.375,3 1.531,3.167 0.156,0.167 10 false B 2.135,1.625 2.292,1.792 0.156,0.167 10 false 1 0.802,0.969 0.979,1.135 0.177,0.167 10 false 10 2.135,0.969 2.292,1.135 0.156,0.167 10 false 2 1.656,2.219 1.833,2.385 0.177,0.167 10 false 11 2.76,0.979 2.917,1.146 0.156,0.167 10 false 3 1.667,0.344 1.844,0.51 0.177,0.167 10 false 12 2.771,1.625 2.927,1.792 0.156,0.167 10 false 4 2.281,0.344 2.458,0.51 0.177,0.167 10 false 13 1.521,1.625 1.677,1.792 0.156,0.167 10 false 5 2.281,2.229 2.458,2.396 0.177,0.167 10 false 14 1.51,0.969 1.667,1.135 0.156,0.167 10 false 6 1.031,2.219 1.208,2.385 0.177,0.167 10 false 15 3.26,1.083 3.417,1.25 0.156,0.167 10 false 7 1.042,0.333 1.219,0.5 0.177,0.167 10 false 16 3.25,1.875 3.406,2.042 0.156,0.167 10 false 8 3,0.344 3.177,0.51 0.177,0.167 10 false 17 0.833,1.615 0.99,1.781 0.156,0.167 10 false 9 3,2.219 3.177,2.385 0.177,0.167 10 false 18 0.323,2.229 0.5,2.396 0.177,0.167 10 false 19 0.344,0.344 0.521,0.51 0.177,0.167 10 false 20

Step 1:

HINT:
·

The crankshaft bearing cap bolts are tightened in 4 progressive steps.

·

If any crankshaft bearing cap bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the 20 crankshaft bearing cap bolts A and B.


ii.

Install the 20 crankshaft bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

Torque:
for bolt A : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for bolt B : 60 N*m (612 kgf*cm, 44 ft.*lbf)



k.
U162928E02
1.188,3.458 2.115,3.99 2.115,3.99 2.354,3.99 true 2.125,1.344 2.281,1.51 0.156,0.167 10 false 1 0.802,0.698 0.979,0.865 0.177,0.167 10 false 10 2.135,0.698 2.292,0.865 0.156,0.167 10 false 2 1.667,1.938 1.844,2.104 0.177,0.167 10 false 11 2.771,0.708 2.927,0.875 0.156,0.167 10 false 3 1.677,0.083 1.854,0.25 0.177,0.167 10 false 12 2.76,1.344 2.917,1.51 0.156,0.167 10 false 4 2.292,0.083 2.469,0.25 0.177,0.167 10 false 13 1.521,1.344 1.677,1.51 0.156,0.167 10 false 5 2.281,1.938 2.458,2.104 0.177,0.167 10 false 14 1.521,0.698 1.677,0.865 0.156,0.167 10 false 6 1.042,1.927 1.219,2.094 0.177,0.167 10 false 15 3.271,0.792 3.427,0.958 0.156,0.167 10 false 7 1.042,0.083 1.219,0.25 0.177,0.167 10 false 16 3.26,1.583 3.417,1.75 0.156,0.167 10 false 8 3.01,0.094 3.188,0.26 0.177,0.167 10 false 17 0.823,1.344 0.979,1.51 0.156,0.167 10 false 9 3,1.927 3.177,2.094 0.177,0.167 10 false 18 0.323,1.938 0.5,2.104 0.177,0.167 10 false 19 0.354,0.094 0.531,0.26 0.177,0.167 10 false 20 0.104,3.688 0.469,3.833 0.365,0.146 10 false Front 0.646,4.115 0.802,4.281 0.156,0.167 10 false A 0.646,4.427 0.802,4.594 0.156,0.167 10 false B 0.719,2.677 0.979,2.844 0.26,0.167 10 false 90° 2.417,3.906 3.271,4.052 0.854,0.146 10 false Painted Mark

Step 2:

i.

Mark the front side of the crankshaft bearing cap bolts A and B with paint.


ii.

Tighten the crankshaft bearing cap bolts A and B 90° in the sequence shown in the illustration.



l.
U162929E02
1.594,2.938 2.104,3.979 2.104,3.979 2.26,3.979 true 2.135,1.344 2.292,1.51 0.156,0.167 10 false 1 0.802,0.698 0.979,0.865 0.177,0.167 10 false 10 2.135,0.688 2.292,0.854 0.156,0.167 10 false 2 2.771,0.698 2.927,0.865 0.156,0.167 10 false 3 2.771,1.344 2.927,1.51 0.156,0.167 10 false 4 1.521,1.344 1.677,1.51 0.156,0.167 10 false 5 1.521,0.688 1.677,0.854 0.156,0.167 10 false 6 3.26,0.792 3.417,0.958 0.156,0.167 10 false 7 3.26,1.583 3.417,1.75 0.156,0.167 10 false 8 0.833,1.333 0.99,1.5 0.156,0.167 10 false 9 0.083,3.625 0.448,3.792 0.365,0.167 10 false Front 0.646,4.344 0.802,4.51 0.156,0.167 10 false A 2.26,2.521 2.51,2.688 0.25,0.167 10 false 90° 2.323,3.896 3.167,4.063 0.844,0.167 10 false Painted Mark

Step 3:

i.

Tighten the crankshaft bearing cap bolts A another 90° in the sequence shown in the illustration.



m.
A170349E05
2.365,1.167 2.771,1.406 2.771,1.406 2.771,1.542 true 0.354,1.438 0.771,1.635 0.417,0.198 10 false Front 2.323,1.583 3.167,1.74 0.844,0.156 10 false Painted Mark

Check that the painted marks of bolt A are now at a 180° angle to the front.


n.
A170350E06
1.802,0.573 2.063,0.25 2.063,0.25 2.177,0.25 true 2.229,0.177 3.094,0.448 0.865,0.271 10 false Painted Mark 0.354,1.427 0.75,1.667 0.396,0.24 10 false Front

Check that the painted marks of bolt B are now at a 90° angle to the front.


o.

Check that the crankshaft turns smoothly.


p.
U162921E02
1.708,1.927 1.865,2.094 0.156,0.167 10 false 1 0.344,0.104 0.521,0.271 0.177,0.167 10 false 10 1.719,0.094 1.875,0.26 0.156,0.167 10 false 2 2.333,0.094 2.49,0.26 0.156,0.167 10 false 3 2.333,1.927 2.49,2.094 0.156,0.167 10 false 4 1.094,1.927 1.25,2.094 0.156,0.167 10 false 5 1.083,0.094 1.24,0.26 0.156,0.167 10 false 6 3.052,0.104 3.208,0.271 0.156,0.167 10 false 7 2.938,1.802 3.094,1.969 0.156,0.167 10 false 8 0.385,1.927 0.542,2.094 0.156,0.167 10 false 9

Step 4:

i.

Using several steps, install the 10 crankshaft bearing cap bolts uniformly in the sequence shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)


ii.

Check that the crankshaft turns smoothly.



Hide 11.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.

A385761E01
3.156,3.031 3.156,2.625 3.156,2.625 3.531,2.083 true 0.563,3.031 0.563,2.208 0.563,2.208 0.938,2.083 true 0.563,2.198 0.938,1.865 true 0.177,0.344 1.073,0.594 0.896,0.25 12 false for Bank 1: 3.052,0.323 3.948,0.573 0.896,0.25 12 false for Bank 2: 0.313,3.104 1.208,3.354 0.896,0.25 10 false Front Mark 2.917,3.104 3.813,3.354 0.896,0.25 10 false Front Mark 5.563,1.188 7.104,1.375 1.542,0.188 10 false No. 1 Compression Ring 5.563,1.656 7.104,1.844 1.542,0.188 10 false No. 2 Compression Ring 5.573,2.125 6.146,2.313 0.573,0.188 10 false Oil Ring 5.583,2.604 6.781,2.802 1.198,0.198 10 false Oil Ring Expander 5.354,1.177 5.563,1.365 0.208,0.188 10 false A 0.813,1.177 1.021,1.365 0.208,0.188 10 false A 4.813,2.573 5.021,2.76 0.208,0.188 10 false A 5.354,1.656 5.563,1.844 0.208,0.188 10 false B 2.229,2.573 2.438,2.76 0.208,0.188 10 false B 3.396,1.177 3.604,1.365 0.208,0.188 10 false B 5.344,2.115 5.552,2.302 0.208,0.188 10 false C 0.802,2.573 1.01,2.76 0.208,0.188 10 false C 4.802,1.188 5.01,1.375 0.208,0.188 10 false C 5.354,2.594 5.563,2.781 0.208,0.188 10 false D 3.385,2.573 3.594,2.76 0.208,0.188 10 false D 2.229,1.177 2.438,1.365 0.208,0.188 10 false D


b.

Check the positions of the piston ring ends.


c.

Using a hammer handle and piston ring compressor, press a piston and connecting rod assembly into each cylinder with the front mark of the piston facing forward.

A385766E01
3.75,1.927 4.24,1.927 4.24,1.927 4.24,2.135 true 0.823,0.938 1.052,0.938 1.052,0.938 1.052,0.885 true 0.896,0.875 1.26,0.875 true 1.313,0.802 2.021,1 0.708,0.198 10 false Front Mark 0.104,1.74 0.458,1.917 0.354,0.177 10 false RH: 4.042,0.448 4.313,0.646 0.271,0.198 10 false LH: 3.844,2.167 4.646,2.365 0.802,0.198 10 false Front Mark 2.781,2.208 3.146,2.417 0.365,0.208 10 false Front


d.
U162906E02
0.573,0.49 0.708,0.979 0.708,0.979 0.708,1.104 true 2.656,0.74 2.667,1.177 true 0.135,0.125 0.396,0.271 0.26,0.146 10 true RH: 0.458,1.146 1.115,1.292 0.656,0.146 10 false Protrusion 2.125,1.146 2.896,1.375 0.771,0.229 10 true Protrusion 0.094,0.813 0.458,0.958 0.365,0.146 10 false Front 1.917,0.104 2.167,0.25 0.25,0.146 10 false LH: 2.927,0.969 3.25,1.219 0.323,0.25 10 true Rear

Install the connecting rod cap so that its protrusion is facing the correct direction.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



e.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


f.

Step 1:

i.
A164565

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)

HINT:
·

The connecting rod cap bolts are tightened in 2 progressive steps.

·

If any connecting rod cap bolt is broken or deformed, replace it.





g.

Step 2:

i.
A158686E09
1.49,1.156 1.208,1.656 1.208,1.656 1.208,1.802 true 0.135,1.354 0.49,1.51 0.354,0.156 10 false Front 0.76,1.844 1.615,2 0.854,0.156 10 false Painted Mark 1.042,0.365 1.281,0.531 0.24,0.167 10 false 90°

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the cap bolts 90°.



h.
A170350E06
1.802,0.573 2.063,0.25 2.063,0.25 2.177,0.25 true 2.229,0.177 3.094,0.448 0.865,0.271 10 false Painted Mark 0.354,1.427 0.75,1.667 0.396,0.24 10 false Front

Check that the painted marks are now at a 90° angle to the front.


i.

Check that the crankshaft turns smoothly.