Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL FILTER
RM2660E _51 Engine / Hybrid System _052780 1GR-FE FUEL _0255080 FUEL FILTER A

1GR-FE FUEL  FUEL FILTER  REPLACEMENT  


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77266A 4.REMOVE NO. 1 FUEL TUBE PROTECTOR

a.
A181395

Remove the 4 bolts and No. 1 fuel tube protector.


Hide 77206C 5.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

a.
A175098E05
1.656,1.854 1.531,1.854 1.531,1.854 1.417,2.094 false 0.51,2.958 0.646,2.958 0.646,2.958 1.115,3.5 false 1.823,2.99 1.958,2.99 1.958,2.99 2.333,3.448 false 3.083,3.198 2.979,3.198 2.979,3.198 2.792,3.594 false 1.885,3.865 1.885,4.302 1.885,4.302 1.5,4.302 false 1.781,3.896 1.781,4.302 false 2.802,4.271 2.698,4.271 2.698,4.271 2.469,4.021 false 1.729,1.781 2.313,1.938 0.583,0.156 10 false *1 0.344,2.885 0.865,3.042 0.521,0.156 10 false *2 1.635,2.917 2.156,3.073 0.521,0.156 10 false *1 3.094,3.125 3.313,3.302 0.219,0.177 10 false *3 1.354,4.229 1.875,4.385 0.521,0.156 10 false *4 2.833,4.188 3.052,4.365 0.219,0.177 10 false *5

Pull up the retainer and disconnect the No. 2 fuel main tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector


Hide 77251B 6.DISCONNECT FUEL MAIN TUBE

a.
A175100E04
1.99,1.823 1.865,1.823 1.865,1.823 1.75,2.073 false 0.635,2.865 0.781,2.865 0.781,2.865 1.083,3.365 false 1.979,2.885 2.125,2.885 2.125,2.885 2.375,3.302 false 3.083,3.042 2.958,3.042 2.958,3.042 2.813,3.458 false 1.885,3.75 1.885,4.167 1.885,4.167 1.552,4.167 false 1.781,3.75 1.781,4.167 false 2.823,4.229 2.698,4.229 2.698,4.229 2.479,3.896 false 2.052,1.75 2.635,1.906 0.583,0.156 10 false *1 0.448,2.792 0.656,2.969 0.208,0.177 10 false *2 1.813,2.813 2.021,2.99 0.208,0.177 10 false *1 3.135,2.958 3.344,3.135 0.208,0.177 10 false *3 1.396,4.083 1.604,4.26 0.208,0.177 10 false *4 2.885,4.135 3.094,4.313 0.208,0.177 10 false *5

Pull up the retainer and disconnect the fuel main tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector


Hide 23300J 7.REMOVE FUEL FILTER ASSEMBLY

a.
A175102

Remove the 2 bolts and fuel filter.


Hide 23300J 8.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter with the 2 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 77251B 9.CONNECT FUEL MAIN TUBE

a.
A175101E04
2.052,1.854 1.938,1.854 1.938,1.854 1.781,2.219 true 0.729,2.948 0.906,2.948 0.906,2.948 1.104,3.365 true 1.958,2.875 2.135,2.875 2.135,2.875 2.333,3.292 true 3.115,3.052 2.958,3.052 2.958,3.052 2.833,3.469 true 1.917,3.76 1.917,4.177 1.917,4.177 1.594,4.177 false 1.813,3.75 1.813,4.177 false 2.875,4.25 2.719,4.25 2.719,4.25 2.531,3.917 true 2.104,1.771 2.688,1.927 0.583,0.156 10 false *1 0.552,2.875 1.135,3.031 0.583,0.156 10 false *2 1.802,2.802 2.385,2.958 0.583,0.156 10 false *1 3.135,2.969 3.344,3.125 0.208,0.156 10 false *3 1.438,4.115 1.646,4.271 0.208,0.156 10 false *4 2.917,4.177 3.125,4.333 0.208,0.156 10 false *5

Connect the fuel main tube and push the retainer.

NOTICE:
·

Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

HINT:

Push the parts together firmly until a "click" sound is heard.



Hide 77206C 10.CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

a.
A175099E04
1.688,1.875 1.573,1.875 1.573,1.875 1.396,2.24 true 0.667,2.885 0.823,2.885 0.823,2.885 1.052,3.354 true 1.99,2.885 2.146,2.885 2.146,2.885 2.354,3.292 true 3.094,2.979 2.99,2.979 2.99,2.979 2.833,3.469 true 1.896,3.74 1.896,4.146 1.896,4.146 1.563,4.146 false 1.792,3.76 1.792,4.135 false 2.854,4.177 2.75,4.177 2.75,4.177 2.531,3.896 true 1.729,1.813 2.313,1.969 0.583,0.156 10 false *1 0.458,2.802 0.635,2.99 0.177,0.188 10 false *2 1.833,2.802 2.01,2.99 0.177,0.188 10 false *1 3.135,2.896 3.313,3.083 0.177,0.188 10 false *3 1.406,4.073 1.583,4.26 0.177,0.188 10 false *4 2.885,4.094 3.063,4.281 0.177,0.188 10 false *5

Connect the No. 2 fuel main tube and push the retainer.

NOTICE:
·

Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.



Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

HINT:

Push the parts together firmly until a "click" sound is heard.



Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77266A 13.INSTALL NO. 1 FUEL TUBE PROTECTOR

a.

Install the No. 1 fuel tube protector and 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)