Home › Engine / Hybrid System › 3UR-FE (FUEL) › FUEL FILTER › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052781 3UR-FE FUEL _0255090 FUEL FILTER A

3UR-FE FUEL  FUEL FILTER  REPLACEMENT  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77266A 4.REMOVE NO. 1 FUEL TUBE PROTECTOR

a.
A181395

Remove the 4 bolts and No. 1 fuel tube protector.


Hide 77206C 5.DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

a.
A175098E02
2.731,4.061 2.929,4.243 0.198,0.183 10 *3 1.819,2.914 1.994,3.090 0.175,0.176 10 *1 1.701,1.765 1.891,1.949 0.191,0.184 10 *1 1.858,4.203 2.037,4.374 0.179,0.171 10 *5 1.051,4.067 1.241,4.252 0.190,0.185 10 *4 0.778,2.905 0.946,3.091 0.169,0.186 10 *2 2.038,3.004 2.195,3.004 2.195,3.004 2.405,3.415 false 1.659,1.854 1.541,1.854 1.541,1.854 1.431,2.068 false 0.992,2.991 1.149,2.991 1.149,2.991 1.037,3.483 false 2.081,4.289 2.237,4.289 2.237,4.289 2.318,4.005 false 1.889,3.863 1.557,4.157 1.557,4.157 1.273,4.157 false 1.783,3.863 1.44,4.158 false 2.848,3.704 2.848,4.055 false

Pull up the retainer and disconnect the No. 2 fuel main tube.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77251B 6.DISCONNECT FUEL MAIN TUBE

a.
A175100E02
2.717,4.012 2.891,4.174 0.175,0.161 10 *3 1.851,2.788 2.012,2.966 0.161,0.178 10 *1 2.069,1.734 2.252,1.898 0.184,0.164 10 *1 1.752,4.109 1.937,4.273 0.185,0.164 10 *5 1.065,4.097 1.248,4.266 0.183,0.169 10 *4 0.778,2.774 0.962,2.949 0.184,0.176 10 *2 2.038,2.87 2.195,2.87 2.195,2.87 2.405,3.281 false 2.033,1.817 1.901,1.817 1.901,1.817 1.773,2.067 false 0.992,2.858 1.149,2.858 1.149,2.858 1.037,3.349 false 1.967,4.198 2.124,4.198 2.124,4.198 2.204,3.867 false 1.889,3.729 1.557,4.184 1.557,4.184 1.273,4.184 false 1.783,3.729 1.44,4.185 false 2.831,3.578 2.831,3.999 false

Pull up the retainer and disconnect the fuel main tube.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 23300J 7.REMOVE FUEL FILTER ASSEMBLY

a.
A175102

Remove the 2 bolts and fuel filter.


Hide 23300J 8.INSTALL FUEL FILTER ASSEMBLY

a.

Install the fuel filter with the 2 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 77251B 9.CONNECT FUEL MAIN TUBE

a.
A175101E02
2.756,4.051 2.942,4.217 0.186,0.166 10 *3 1.866,2.791 2.030,2.958 0.165,0.167 10 *1 2.084,1.771 2.254,1.944 0.170,0.173 10 *1 1.791,4.141 1.973,4.311 0.182,0.170 10 *5 1.086,4.115 1.265,4.293 0.178,0.178 10 *4 0.824,2.771 0.990,2.943 0.166,0.173 10 *2 2.067,2.872 2.224,2.872 2.224,2.872 2.435,3.282 false 2.046,1.855 1.918,1.855 1.918,1.855 1.778,2.201 false 1.021,2.859 1.178,2.859 1.178,2.859 1.067,3.35 false 1.995,4.227 2.152,4.227 2.152,4.227 2.305,3.87 false 1.919,3.73 1.576,4.205 1.576,4.205 1.293,4.205 false 1.813,3.73 1.459,4.206 false 2.867,3.581 2.867,4.035 false

Connect the fuel main tube and push the retainer.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

HINT:

Push the parts together firmly until a "click" sound is heard.


NOTICE:
·

Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.




Hide 77206C 10.CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

a.
A175099E02
2.723,4.094 2.900,4.267 0.177,0.172 10 *3 1.863,2.792 2.035,2.968 0.173,0.177 10 *1 1.715,1.814 1.915,1.990 0.200,0.176 10 *1 1.694,4.163 1.876,4.327 0.181,0.164 10 *5 1.064,4.136 1.250,4.305 0.186,0.169 10 *4 0.798,2.769 0.984,2.959 0.186,0.190 10 *2 2.062,2.872 2.219,2.872 2.219,2.872 2.43,3.283 false 1.68,1.9 1.563,1.9 1.563,1.9 1.4,2.217 false 1.016,2.859 1.173,2.859 1.173,2.859 1.062,3.35 false 1.899,4.253 2.056,4.253 2.056,4.253 2.151,3.871 false 1.913,3.731 1.566,4.22 1.566,4.22 1.283,4.22 false 1.808,3.731 1.45,4.221 false 2.837,3.579 2.837,4.083 false

Connect the No. 2 fuel main tube and push the retainer.

Text in Illustration
*1 Retainer
*2 Nylon Tube
*3 Pipe
*4 O-Ring
*5 Connector

HINT:

Push the parts together firmly until a "click" sound is heard.


NOTICE:
·

Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.




Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 77266A 13.INSTALL NO. 1 FUEL TUBE PROTECTOR

a.

Install the No. 1 fuel tube protector with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)