Home › Engine / Hybrid System › 3UR-FE (FUEL) › FUEL TANK › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052781 3UR-FE FUEL _0255092 FUEL TANK A

3UR-FE FUEL  FUEL TANK  REMOVAL  


PROCEDURE

Hide 77310A 2.REMOVE FUEL TANK CAP ASSEMBLY

Hide 77606 3.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.
A175014

Remove the 5 bolts and No. 1 fuel tank protector sub-assembly.


Hide 4.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

A308904E01
3.125,2.492 3.317,2.663 0.192,0.171 10 *1 3.922,3.505 4.114,3.676 0.192,0.171 10 *5 2.931,3.553 3.123,3.724 0.192,0.171 10 *4 4.621,2.52 4.813,2.691 0.192,0.171 10 *3 2.177,2.56 2.368,2.731 0.192,0.171 10 *2 3.606,0.068 3.798,0.239 0.192,0.171 10 *b 0.272,0.068 0.463,0.239 0.192,0.171 10 *a 2.353,2.632 2.482,2.632 2.482,2.632 2.592,3.053 false 3.106,2.569 3.013,2.569 3.013,2.569 2.877,2.853 false 3.001,3.347 3.001,3.534 false 3.699,3.235 3.699,3.581 false 3.55,3.235 3.55,3.581 3.55,3.581 3.874,3.581 false 4.584,2.597 4.491,2.597 4.491,2.597 4.355,2.881 false 2.546,0.372 2.738,0.542 0.192,0.171 10 *1 2.527,0.449 2.433,0.449 2.433,0.449 2.296,0.548 false 5.321,0.351 5.513,0.522 0.192,0.171 10 *1 5.302,0.429 5.208,0.429 5.208,0.429 5.028,0.538 false

Text in Illustration
*1 Retainer *2 Pipe
*3 Nylon Tube *4 Connector
*5 O-Ring - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank main tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 5.DRAIN FUEL

a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



d.

Turn the intelligent tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

CAUTION:
·

Do not smoke or be near an open flame when working on the fuel system.

·

Secure good ventilation.

·

Keep gasoline away from rubber or leather parts.



HINT:
A237023

If the fuel pump does not operate, remove the fuel tube joint clip and disconnect the fuel tank return tube, and drain fuel from the port shown in the illustration.



f.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



g.
A237024

Disconnect the fuel pump and fuel sender gauge connector.


Hide 6. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 71300S 8.REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)

Hide 71400S 9.REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)

Hide 10.REMOVE REAR NO. 2 SEAT ASSEMBLY

a.

for Face to Face Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>REMOVAL).


b.

except Face to Face Seat Type:

Remove the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(except Face to Face Seat Type)>REMOVAL).


Hide 58510D 11.REMOVE FRONT FLOOR CARPET ASSEMBLY

a.

Turn over the floor carpet.

HINT:

Fold back the floor carpet so that the air duct can be removed.



Hide 58329F 12.REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER

a.
A181426

Remove the 2 screws and air duct.


b.
A181427

Remove the rear floor No. 2 service hole cover.


Hide 13.DISCONNECT NO. 2 FUEL TANK BREATHER HOSE

a.
A308892

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Slide the clip and disconnect the No. 2 fuel tank breather hose from the pipe.



Hide 14.DISCONNECT FUEL TANK RETURN TUBE

A308905E01
3.078,2.482 3.257,2.654 0.179,0.172 10 *1 4.624,2.575 4.803,2.747 0.179,0.172 10 *3 2.151,2.551 2.330,2.723 0.179,0.172 10 *2 3.942,3.444 4.121,3.616 0.179,0.172 10 *5 2.941,3.556 3.120,3.728 0.179,0.172 10 *4 0.276,0.072 0.455,0.244 0.179,0.172 10 *a 3.624,0.072 3.803,0.244 0.179,0.172 10 *b 2.337,2.62 2.449,2.62 2.449,2.62 2.596,3.036 false 3.041,2.553 2.925,2.553 2.925,2.553 2.862,2.851 false 4.585,2.648 4.494,2.648 4.494,2.648 4.41,2.881 false 3.699,3.234 3.699,3.503 false 3.913,3.503 3.55,3.503 3.55,3.503 3.55,3.234 false 3.006,3.346 3.006,3.54 false 2.524,0.321 2.704,0.493 0.179,0.172 10 *1 2.487,0.392 2.372,0.392 2.372,0.392 2.248,0.498 false 5.302,0.202 5.481,0.374 0.179,0.172 10 *1 5.265,0.273 5.149,0.273 5.149,0.273 5.025,0.376 false

Text in Illustration
*1 Retainer *2 Pipe
*3 Nylon Tube *4 Connector
*5 O-Ring - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank return tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 77027B 15.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A308891E01
1.825,0.121 2.013,0.305 0.188,0.184 10 *1 1.862,4.016 2.051,4.199 0.188,0.184 10 *5 0.962,4.186 1.150,4.369 0.188,0.184 10 *4 2.574,3.042 2.762,3.226 0.188,0.184 10 *3 0.185,3.005 0.373,3.188 0.188,0.184 10 *2 1.233,2.967 1.421,3.151 0.188,0.184 10 *1 0.397,3.096 0.5,3.096 0.5,3.096 0.629,3.572 false 1.199,3.059 1.093,3.059 1.093,3.059 0.961,3.346 false 1.044,3.918 1.044,4.165 false 2.562,3.125 2.446,3.125 2.446,3.125 2.353,3.38 false 1.601,3.802 1.601,4.099 false 1.812,4.099 1.474,4.099 1.474,4.099 1.474,3.802 false 1.783,0.217 1.677,0.217 1.677,0.217 1.49,0.392 false

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull up the retainer and disconnect the No. 1 fuel emission tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Pipe
*3 Nylon Tube
*4 Connector
*5 O-Ring
V100135

Pull Up



b.
A310181E01
2.85,0.245 3.041,0.414 0.191,0.170 10 *1 0.225,2.728 0.415,2.898 0.191,0.170 10 *4 1.329,2.72 1.520,2.889 0.191,0.170 10 *3 0.994,4.151 1.185,4.320 0.191,0.170 10 *2 2.756,2.845 2.946,3.015 0.191,0.170 10 *5 2.816,0.326 2.696,0.326 2.696,0.326 2.524,0.569 false 2.717,2.939 2.541,2.939 2.541,2.939 2.351,3.189 false 1.093,3.746 1.093,4.138 false 0.771,3.309 0.608,2.822 0.608,2.822 0.453,2.822 false 1.303,2.81 1.097,2.81 1.097,2.81 1.097,3.202 false

except G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull the retainer up while pinching it on both sides by hand as shown in the illustration, and disconnect the No. 1 fuel emission tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Connector
*3 O-Ring
*4 Pipe
*5 Nylon Tube
V100135

Push
V100136

Pull Up



Hide 77259E 16.DISCONNECT FUEL HOSE

a.
A308893

for G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Slide the clip and disconnect the fuel hose from the pipe.



Hide 77206C 17.DISCONNECT NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY

A308906E03
3.688,3.188 4.021,3.188 false 4.021,3.188 4.021,3.5 false 3.688,3.292 4.021,3.292 false 3.073,3.156 3.167,3.156 3.167,3.156 3.25,3.406 false 3.354,2.5 3.542,2.5 3.542,2.5 3.594,2.698 false 3.74,2.833 3.958,2.698 3.958,2.698 4.063,2.698 true 3.792,2.948 4.073,2.948 false 1.167,0.792 1.396,0.656 1.396,0.656 1.5,0.656 false 4.365,0.51 4.594,0.375 4.594,0.375 4.698,0.375 false 4.094,2.615 4.292,2.792 0.198,0.177 10 false *1 4.094,2.865 4.292,3.042 0.198,0.177 10 false *2 3.958,3.51 4.156,3.688 0.198,0.177 10 false *3 3.156,2.438 3.354,2.615 0.198,0.177 10 false *4 2.896,3.083 3.094,3.26 0.198,0.177 10 false *5 0.271,0.073 0.469,0.25 0.198,0.177 10 false *a 3.615,0.073 3.813,0.25 0.198,0.177 10 false *b 1.521,0.583 1.719,0.76 0.198,0.177 10 false *1 4.729,0.302 4.927,0.479 0.198,0.177 10 false *1

Text in Illustration
*1 Retainer *2 Connector
*3 O-Ring *4 Pipe
*5 Nylon Tube - -
*a except G.C.C. Countries *b for G.C.C. Countries
V100135

Pull Up - -

a.

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the No. 2 fuel tank main tube sub-assembly.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




Hide 18.DISCONNECT NO. 2 FUEL TANK BREATHER TUBE

a.
A310185E01
2.777,0.2 2.978,0.387 0.201,0.187 10 *1 2.751,0.298 2.615,0.298 2.615,0.298 2.399,0.474 false 0.96,3.493 1.150,3.670 0.191,0.177 10 *5 2.59,3.884 2.781,4.061 0.191,0.177 10 *3 2.528,3.265 2.719,3.442 0.191,0.177 10 *2 1.437,2.788 1.627,2.965 0.191,0.177 10 *4 2.528,2.947 2.719,3.124 0.191,0.177 10 *1 1.651,2.87 1.849,2.87 1.849,2.87 1.997,3.115 false 2.498,3.351 2.252,3.351 false 2.498,3.042 2.408,3.042 2.408,3.042 2.142,3.264 false 2.119,3.605 2.674,3.605 false 2.674,3.605 2.674,3.847 false 2.119,3.744 2.674,3.744 false 1.205,3.579 1.333,3.579 1.333,3.579 1.445,3.883 false

except G.C.C. Countries:

i.

Detach the fuel tube clamp.


ii.

Pull up the retainer and disconnect the No. 2 fuel tank breather tube.

NOTICE:
·

Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



Text in Illustration
*1 Retainer
*2 Connector
*3 O-Ring
*4 Pipe
*5 Nylon Tube
V100135

Pull Up



Hide 19.DISCONNECT FUEL TANK BREATHER TUBE

a.
A310187E01
1.648,2.217 1.853,2.404 0.205,0.187 10 *1 1.609,2.298 1.463,2.298 1.463,2.298 1.23,2.489 false

Detach the fuel tube clamp.


b.

Pull up the retainer and disconnect the fuel tank breather tube from the fuel tank to filler pipe sub-assembly.

Text in Illustration
*1 Retainer
V100135

Pull Up

NOTICE:
·

Do not use any tools in this procedure.

·

Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.




Hide 20.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A175067

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank to filler pipe sub-assembly.


Hide 77100U 21.REMOVE FUEL TANK SUB-ASSEMBLY

a.

Place an engine lifter under the fuel tank sub-assembly.


b.
A175024

Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank band sub-assemblies.


c.

Slowly lower the engine lifter slightly.


Hide 77259E 22.REMOVE FUEL HOSE

a.
A308896

for G.C.C. Countries:

Slide the clip and remove the fuel hose from the fuel suction tube sub-assembly.


Hide 23.REMOVE FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A176319E05
2.585,4.05 2.778,4.229 0.193,0.179 10 *4 2.429,3.324 2.644,3.503 0.215,0.179 10 *3 0.678,3.807 0.890,4.005 0.212,0.198 10 *2 0.988,2.238 1.163,2.420 0.175,0.182 10 *1 1.189,2.325 1.326,2.325 1.326,2.325 1.516,2.884 false 0.781,3.786 0.781,3.659 0.781,3.659 1.342,3.309 false 1.833,3.412 2.387,3.412 false 1.831,3.527 2.239,3.527 2.239,3.527 2.239,3.418 false 2.702,4.023 2.702,3.904 2.702,3.904 1.915,3.744 false

Remove the 3 tube joint clips and pull out the 3 fuel tube joints.

NOTICE:
·

Remove any dirt and foreign matter on the fuel tube joint before performing this work.

·

Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

·

Perform this work by hand. Do not use any tools.

·

Do not forcibly bend, twist or turn the nylon tube.

·

Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.



Text in Illustration
*1 Fuel Tube Joint
*2 Tube Joint Clip
*3 O-Ring
*4 Fuel Suction Plate Sub-assembly


b.
A310189E02
1.677,0.531 1.333,0.531 true 1.844,0.615 2.063,0.115 2.063,0.115 2.177,0.115 true 2.688,0.885 3.031,0.531 3.031,0.531 3.125,0.531 true 1.156,0.427 1.365,0.604 0.208,0.177 10 true *1 3.156,0.448 3.365,0.625 0.208,0.177 10 false *3 2.229,0.042 2.438,0.219 0.208,0.177 10 false *2

except G.C.C. Countries:

i.

Detach the clamp and remove the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Return Tube Sub-assembly
*3 No. 2 Fuel Tank Main Tube Sub-assembly


ii.

Detach the clamp and remove the fuel tank return tube sub-assembly.


iii.

Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.



c.
A308897E02
0.958,0.302 0.625,0.302 true 1.646,0.146 1.49,0.146 1.49,0.146 1.146,0.354 true 2.292,0.698 2.396,0.531 2.396,0.531 2.479,0.531 false 1.667,0.052 1.854,0.219 0.188,0.167 10 true *2 2.49,0.448 2.677,0.615 0.188,0.167 10 false *3 0.417,0.219 0.604,0.385 0.188,0.167 10 true *1

for G.C.C. Countries:

i.

Detach the clamp and remove the fuel tank main tube sub-assembly.

Text in Illustration
*1 Fuel Tank Main Tube Sub-assembly
*2 Fuel Tank Return Tube Sub-assembly
*3 No. 2 Fuel Tank Main Tube Sub-assembly


ii.

Detach the clamp and remove the fuel tank return tube sub-assembly.


iii.

Detach the 2 clamps and remove the No. 2 fuel tank main tube sub-assembly.



Hide 77020A 24.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77213B 25.REMOVE FUEL TANK TO FILLER PIPE HOSE

a.
A176316

Loosen the hose clamp and remove the fuel tank to filler pipe hose from the fuel tank sub-assembly.


Hide 77697 26.REMOVE NO. 1 FUEL TANK HEAT INSULATOR

a.
U163755E02
1.771,0.167 1.969,0.354 0.198,0.188 10 false *a 1.677,3.323 1.802,3.49 0.125,0.167 10 false 2 0.729,3.313 0.854,3.479 0.125,0.167 10 false 1 2.625,3.323 2.75,3.49 0.125,0.167 10 false 3

Remove the fuel tube clamp from the No. 1 fuel tank heat insulator.

Text in Illustration
*a for G.C.C. Countries


b.

Using needle-nose pliers, remove the 4 clips shown in the illustration, and then remove the No. 1 fuel tank heat insulator.