Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255064 ENGINE ASSEMBLY A

1VD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines.


PROCEDURE

Hide 1.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55781E 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 12601E 5.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

Hide 53292A 6.REMOVE UPPER RADIATOR SUPPORT SEAL

Hide 28800 7.REMOVE MAIN BATTERY

Hide 8.REMOVE SUB-BATTERY

Hide 9.REMOVE FRONT WHEEL

Hide 53301 10.REMOVE HOOD SUB-ASSEMBLY

a.
A174152

Remove the 2 hood stay bolts. Then disconnect the 2 hood supports.

NOTICE:
·

Avoid touching the stroke portions of the rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.

·

Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.

·

Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.

·

Remove the hood support while supporting the hood by hand.




b.

Remove the 4 bolts and hood.


Hide 53806 11.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

a.
A271735

Remove the 3 bolts and screw.


b.

Loosen the clip and remove the front fender splash shield LH.


Hide 53805 12.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

a.

Remove the 3 bolts and 2 screws.


b.

Loosen the clip and remove the front fender splash shield RH.


Hide 51405A 13.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.
A178461

Remove the 10 bolts and No. 1 engine under cover.


Hide 51442 14.REMOVE NO. 2 ENGINE UNDER COVER

a.
A178462

Remove the 2 bolts and No. 2 engine under cover.


Hide 17.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.
A177219

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Install a new gasket and the oil pan drain plug.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 17940D 18.REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

Hide 82113 19.REMOVE NO. 3 ENGINE ROOM WIRE

Hide 17801 21.REMOVE AIR CLEANER FILTER ELEMENT

Hide 22.REMOVE AIR CLEANER CASE

a.
A174700

Using a clip remover, detach the wire harness clamp.


b.

Remove the 3 bolts and air cleaner case.


Hide 44360 25.REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

Hide 44369A 26.REMOVE NO. 1 OIL RESERVOIR BRACKET

Hide 16470 27.REMOVE RADIATOR RESERVOIR ASSEMBLY

Hide 16571C 29.DISCONNECT NO. 1 RADIATOR HOSE

Hide 16572D 30.DISCONNECT NO. 2 RADIATOR HOSE

Hide 31.REMOVE V-RIBBED BELT (w/ Viscous Heater)

Hide 32.REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

Hide 33.REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

Hide 53782 35.REMOVE FRONT FENDER APRON SEAL FRONT RH

a.
A177003

Remove the 3 clips and front fender apron seal front RH.


Hide 53784 36.REMOVE FRONT FENDER APRON SEAL REAR RH

a.
A177002

Remove the 4 clips and front fender apron seal rear RH.


Hide 53783 37.REMOVE FRONT FENDER APRON SEAL FRONT LH

a.
A176301

w/o KDSS:

Remove the 4 clips and front fender apron seal front LH.


b.
A177004

w/ KDSS:

Remove the 3 clips and front fender apron seal front LH.


Hide 53785B 38.REMOVE FRONT FENDER APRON SEAL REAR LH

a.
A177005

Remove the 4 clips and front fender apron seal rear LH.


Hide 32942 39.REMOVE OIL COOLER TUBE (for Automatic Transmission)

Hide 16371 41.REMOVE FAN PULLEY

Hide 52049 42.REMOVE FRONT BUMPER WINCH COVER (w/ Winch)

Hide 32917 45.REMOVE TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)

Hide 53293C 46.DISCONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)

Hide 53294C 47.DISCONNECT RADIATOR SIDE DEFLECTOR LH

Hide 41533 49.DISCONNECT FRONT DIFFERENTIAL BREATHER TUBE

A177338

Hide 77251B 50.DISCONNECT FUEL TUBE

a.

w/ DPF:

Disconnect the 2 fuel tubes from the No. 1 and No. 3 fuel tube clamps.


b.

w/o DPF:

Disconnect the 3 fuel tubes from the No. 1 and No. 3 fuel tube clamps.


Hide 17973 51.REMOVE NO. 1 COOL AIR INLET (w/o Intercooler)

Hide 17973 52.REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

Hide 54.REMOVE NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 57.DRAIN CLUTCH FLUID (for Manual Transmission)

Hide 31418 58.REMOVE CLUTCH HOSE (for Manual Transmission)

Hide 31489 60.REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)

Hide 17947B 62.REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

Hide 26100G 63.REMOVE DIESEL THROTTLE BODY ASSEMBLY LH

Hide 17360E 66.REMOVE NO. 1 AIR TUBE ASSEMBLY

a.
A174709

Remove the bolt and No. 1 air tube.


b.

Remove the O-ring.


Hide 69.REMOVE NO. 2 AIR TUBE ASSEMBLY

a.
A174707

Remove the bolt and No. 2 air tube.


b.

Remove the O-ring.


Hide 17806 70.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 88711 71.REMOVE NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88320 73.REMOVE COOLER COMPRESSOR ASSEMBLY

a.
A174754

Disconnect the 4 connectors.


b.

Using a clip remover, detach the 3 wire harness clamps.


c.
E154192

Remove the 4 bolts and cooler compressor.


Hide 17877 74.REMOVE NO. 2 INTAKE AIR CONNECTOR PIPE

a.
A174712

w/ Intercooler:

Disconnect the vacuum hose.


b.
A174713

Loosen the hose clamp, and remove the bolt and No. 2 intake air connector pipe.


Hide 87208 75.REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

Hide 17885 76.REMOVE NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY

Hide 16268M 78.REMOVE NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)

Hide 80.DISCONNECT ENGINE WIRE

a.

LH Side:

i.
A267317E01
0.069,0.081 0.254,0.236 0.185,0.155 10 *A 0.069,2.42 0.254,2.574 0.185,0.155 10 *B

w/ DPF:

Disconnect the 7 connectors from the injector driver.

Text in Illustration
*A w/ DPF
*B w/o DPF


ii.

w/o DPF:

Disconnect the 4 connectors from the injector driver.


iii.

Disconnect the 4 connectors and detach the wire harness holder from the relay block.


iv.

Remove the bolt and disconnect the ground wire.


v.

Disconnect the wire harness from the wire harness clamp holder.


vi.
U162978E02
2.01,1.51 2.167,1.677 0.156,0.167 10 false A 0.896,2.115 1.052,2.281 0.156,0.167 10 false B

Remove the bolt and disconnect the ground wire from the body panel.


vii.

Using a clip remover, detach the ground wire clamp labeled A from the relay block side.


viii.

Disconnect the wire harness from the wire harness clamp holder labeled B.


ix.
A174745

Remove the nut and detach the generator positive (+) cable holder from the relay block.


x.

Disconnect the generator positive (+) cable from the 2 clamps.


xi.
A174755

Disconnect the 2 connectors.


xii.

Using a clip remover, detach the 3 wire harness clamps.


xiii.
U162979E02
1.458,1.583 1.615,1.75 0.156,0.167 10 false A

for RHD:

Disconnect the 4 connectors and detach the wire harness tab labeled A from the relay block.


xiv.

for RHD:

Disconnect the ECM connector.


xv.

for RHD:

Disconnect the wire harness from the wire harness clamp holder.


xvi.

Disconnect the 8 connectors.

U163560E02
1.094,1.51 1.219,1.656 0.125,0.146 10 false A 2.396,2.375 2.521,2.521 0.125,0.146 10 false B 6.417,1.26 6.542,1.406 0.125,0.146 10 false C 0.333,0.031 0.521,0.188 0.188,0.156 10 false *A 3.906,0.031 4.094,0.188 0.188,0.156 10 false *B 1.844,1.396 1.969,1.542 0.125,0.146 10 false A 4.563,1.563 4.688,1.708 0.125,0.146 10 false A 5.438,1.458 5.563,1.604 0.125,0.146 10 false A 6.073,2.479 6.198,2.625 0.125,0.146 10 false B 2.813,1.26 2.938,1.406 0.125,0.146 10 false C 4.885,1.875 5.01,2.021 0.125,0.146 10 false D 1.427,1.875 1.552,2.021 0.125,0.146 10 false D

Text in Illustration
*A w/ DPF *B w/o DPF


xvii.

Remove the bolt and the engine wire harness bracket labeled B.


xviii.

Using a clip remover, detach the wire harness clamp labeled D.


xix.

Remove the 2 bolts and disconnect the engine wire protector labeled A.


xx.

for RHD:

Disconnect the wire harness from the wire harness clamp holder labeled C.



b.

RH Side:

i.
U163124E02
2.542,1.333 2.698,1.5 0.156,0.167 10 false A

for LHD:

Disconnect the 4 connectors, and detach the wire harness holder from the relay block labeled A.


ii.

for LHD:

Disconnect the ECM connector.


iii.

for LHD:

Disconnect the wire harness from the wire harness clamp holder.


iv.

Disconnect the 7 connectors.

U163561E02
2.969,0.469 3.094,0.615 0.125,0.146 10 false A 6.854,1 6.979,1.146 0.125,0.146 10 false B 1.677,0.396 1.802,0.542 0.125,0.146 10 false C 0.177,0 0.365,0.156 0.188,0.156 10 false *A 3.771,0 3.958,0.156 0.188,0.156 10 false *B 1.438,1.427 1.563,1.573 0.125,0.146 10 false A 1.219,1.708 1.344,1.854 0.125,0.146 10 false A 4.833,1.802 4.958,1.948 0.125,0.146 10 false A 5.333,1.438 5.458,1.583 0.125,0.146 10 false A 6.063,0.958 6.188,1.104 0.125,0.146 10 false A 3.281,0.938 3.406,1.083 0.125,0.146 10 false B 5.104,0.635 5.229,0.781 0.125,0.146 10 false C

Text in Illustration
*A w/ DPF *B w/o DPF


v.

Using a clip remover, detach the wire harness clamp.


vi.

Remove the 3 bolts and disconnect the engine wire protector labeled A.


vii.

Remove the bolt and the wire harness bracket labeled B.


viii.

Remove the screw grommet, nut and the glow plug wire harness labeled C.


ix.
A267320E04
0.042,0.073 0.375,0.344 0.333,0.271 10 true *A 0.031,2.458 0.365,2.708 0.333,0.25 10 true *B

for RHD:

Disconnect the wire harness from the wire harness clamp holder.

Text in Illustration
*A w/ DPF
*B w/o DPF


x.

for RHD:

Remove the bolt and wire harness clamp holder.


xi.
A174760

w/ Winch:

Remove the bolt and disconnect the ground wire.



c.

Rear Side:

i.
U163562E02
0.469,1.917 0.594,2.063 0.125,0.146 10 false A 0.865,0.792 0.99,0.938 0.125,0.146 10 false B 1.885,0.208 2.01,0.354 0.125,0.146 10 false C 0.104,0.021 0.292,0.177 0.188,0.156 10 false *A 0.104,2.51 0.292,2.667 0.188,0.156 10 false *B 0.365,4.219 0.49,4.365 0.125,0.146 10 false A 2.906,0.813 3.031,0.958 0.125,0.146 10 false B 2.823,3.229 2.948,3.375 0.125,0.146 10 false B 0.875,3.25 1,3.396 0.125,0.146 10 false B 2.354,0.365 2.479,0.51 0.125,0.146 10 false C 1.625,2.688 1.75,2.833 0.125,0.146 10 false C 2.146,2.688 2.271,2.833 0.125,0.146 10 false C

Using a clip remover, detach the wire harness clamp.

Text in Illustration
*A w/ DPF
*B w/o DPF


ii.

Remove the 2 bolts and 2 ground wires labeled C.


iii.

Remove the 2 bolts and disconnect the engine wire harness protector labeled B.


iv.

w/ DPF:

Disconnect the 3 connectors.


v.

w/o DPF:

Disconnect the connector.


vi.

Remove the screw grommet, nut and disconnect the glow plug wire harness labeled A.



Hide 23802E 81.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)

Hide 23706 82.REMOVE NO. 6 INJECTION PIPE SUB-ASSEMBLY

Hide 25860 83.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)

Hide 25706 84.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)

Hide 11225 85.REMOVE CYLINDER HEAD COVER SILENCER LH (w/ DPF)

Hide 23764A 86.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23812D 88.REMOVE NO. 2 FUEL PIPE (w/ DPF)

Hide 23765 89.REMOVE NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23820A 90.REMOVE COMMON RAIL ASSEMBLY LH

Hide 23801L 91.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY

Hide 23705 93.REMOVE NO. 5 INJECTION PIPE SUB-ASSEMBLY

Hide 11224 94.REMOVE CYLINDER HEAD COVER SILENCER RH (w/ DPF)

Hide 23810A 96.REMOVE COMMON RAIL ASSEMBLY RH

Hide 17135A 97.REMOVE NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 17136 98.REMOVE NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)

Hide 23763 100.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 17853B 104.REMOVE INTAKE MANIFOLD INSULATOR (w/ EGR System)

Hide 25615A 105.REMOVE EGR PIPE INSULATOR (w/ EGR System)

Hide 25620 106.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

Hide 25689 107.REMOVE EGR COOLER INSULATOR (w/ EGR System)

Hide 23763 108.REMOVE NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)

Hide 23764A 109.REMOVE NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)

Hide 16283 110.DISCONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)

Hide 23712 112.REMOVE NO. 2 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 23711 113.REMOVE NO. 1 FUEL INJECTOR PROTECTOR (w/ DPF)

Hide 23901H 114.REMOVE FUEL TUBE SUB-ASSEMBLY (w/ DPF)

Hide 23762B 116.REMOVE NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23761A 117.REMOVE NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)

Hide 23841C 119.REMOVE NO. 1 FUEL PIPE CLAMP (w/ DPF)

Hide 12281A 122.INSTALL NO. 1 AND NO. 2 ENGINE HANGER

a.

Install the No. 1 and No. 2 engine hangers to the cylinder head RH and LH with the 4 bolts as shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

A385771E01
4.156,1.792 4.156,1.021 true 6.021,1.823 6.021,1.302 true 3.146,0.333 3.458,0.531 0.313,0.198 10 false *a 5.115,0.323 5.427,0.521 0.313,0.198 10 false *b 4.073,1.854 4.385,2.052 0.313,0.198 10 false *1 5.948,1.875 6.26,2.073 0.313,0.198 10 false *2

HINT:
No. 1 engine hanger 12281-51040
No. 2 engine hanger 12282-51040
Bolt 91671-80825


Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
*a RH
*b LH


Hide 33030 124.REMOVE MANUAL TRANSMISSION UNIT ASSEMBLY

Hide 31482 125.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)

a.
A177337

Remove the bolt and clutch release cylinder to flexible hose tube.


Hide 126.REMOVE ENGINE ASSEMBLY

a.
A174842

Attach an engine sling device and hang the engine with a chain block.


b.

Remove the 4 bolts from the engine mounting RH and LH side.


c.

Lift the engine out of the vehicle carefully.

NOTICE:
·

Make sure the engine is clear of all wiring and hoses.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




d.

Place the engine onto a work bench.


Hide 31210 127.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 128.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 32101 129.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

a.
A185177

Using a wrench, hold the crankshaft.

NOTICE:

Do not turn the crankshaft counterclockwise.

If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY).


Torque:
108 N*m (1101 kgf*cm, 80 ft.*lbf)

or more



b.
A177363

Remove the 8 bolts.


c.
U163090E02
1.365,2.292 1.365,2.438 false 2.083,2.76 2.083,2.927 false 2.792,2.667 2.792,2.958 false 2.74,3 2.896,3.167 0.156,0.167 10 false A 2.042,2.969 2.198,3.135 0.156,0.167 10 false B 1.313,2.49 1.469,2.656 0.156,0.167 10 false C

Remove the rear drive plate spacer labeled A, drive plate and ring gear labeled B and rear crankshaft balancer weight labeled C.


Hide 13405 130.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

a.
A185177

Using a wrench, hold the crankshaft.

NOTICE:

Do not turn the crankshaft counterclockwise.

If it is turned counterclockwise, check that the crankshaft pulley set bolt is not loose. If loose, tighten the bolt (See page Engine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>REASSEMBLY).


Torque:
108 N*m (1101 kgf*cm, 80 ft.*lbf)

or more



b.
A177365

Remove the 8 bolts and flywheel.


Hide 131.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with bolts.


b.

Remove the 4 bolts and No. 1 and No. 2 engine hangers.