Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › INTAKE MANIFOLD › from 2015.08
RM2660E _51 Engine / Hybrid System _052791 1GR-FE INTAKE / EXHAUST _0255180 INTAKE MANIFOLD A

1GR-FE INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 5.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 6.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 11259 8.REMOVE V-BANK COVER

a.
A267633E02
2.76,0.708 3.094,0.708 true 0.917,0.792 1.031,0.635 1.031,0.635 1.125,0.635 false 3.115,0.615 3.281,0.76 0.167,0.146 10 false *1 1.125,0.542 1.292,0.688 0.167,0.146 10 false *2

Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.

Text in Illustration
*1 Pin
*2 Hook


Hide 17881 9.REMOVE NO. 1 AIR CLEANER HOSE

a.
A267634

Disconnect the No. 2 PCV hose and vacuum hose.


b.

Remove the bolt and loosen the 2 hose clamps.


c.

Remove the No. 1 air cleaner hose.


Hide 17361 10.REMOVE AIR TUBE (w/ Secondary Air Injection System)

a.
A270147

Disconnect the No. 3 air hose.


b.
A270144

for Bank 1 Side:

Remove the bolt and disconnect the air tube assembly from the emission control valve set.


c.
A270145

for Bank 2 Side:

Remove the 2 bolts and disconnect the air tube assembly from the No. 2 emission control valve set.


Hide 17129 11.REMOVE INTAKE AIR SURGE TANK

a.
A270146

Disconnect the throttle body connector.


b.

Disconnect the No. 4 water by-pass hose.


c.

Disconnect the No. 5 water by-pass hose.


d.
A221457

Disconnect the purge line hose.


e.

Disconnect the No. 1 vacuum switching valve connector.


f.

Disconnect the No. 1 PCV hose.


g.
A221460

Remove the 2 bolts and throttle body bracket.


h.
A270141

Detach the 2 wire harness clamps and remove the bolt and bracket.


i.
A221461

Detach the wire harness clamp.


j.
A238095

Remove the 2 bolts and No. 1 surge tank stay.


k.
A270142

for Manual Transmission:

Remove the nut and disconnect the clutch flexible hose bracket.


l.
A272721

Remove the 2 bolts and No. 2 surge tank stay.


m.
A221465

Remove the 2 nuts, 4 bolts and intake air surge tank.


n.

Remove the gasket.


Hide 23807 12.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 17111 13.REMOVE INTAKE MANIFOLD

a.
A271403

Remove the 4 nuts, 6 bolts and 2 gaskets.


Hide 14.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.