Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.

DTC Code DTC Detection Condition Trouble Area
P0571 When the voltage of the STP terminal and the ST1- terminal of the ECM is below than 1 V for 0.5 second. or more.
·

Stop light switch

·

Stop light switch circuit

·

ECM



WIRING DIAGRAM

E149082E04
5.293,1.993 5.690,2.186 0.397,0.193 10 ECM 5.293,1.694 5.737,1.852 0.444,0.159 10 A38*1 0.11,1.879 0.973,2.038 0.863,0.159 10 *2: for RHD 0.11,1.593 0.969,1.752 0.859,0.159 10 *1: for LHD 5.293,1.84 5.737,1.999 0.444,0.159 10 A52*2 4.719,0.449 5.046,0.610 0.327,0.161 10 36*4 4.845,1.051 5.061,1.230 0.216,0.179 10 35 2.761,1.709 3.903,1.915 1.142,0.207 10 Stop Light Switch 2.761,1.538 3.060,1.721 0.299,0.184 10 A30 3.692,0.455 3.876,0.634 0.184,0.179 10 1 2.851,1.056 2.952,1.214 0.100,0.158 10 4 2.848,0.455 3.031,0.634 0.184,0.179 10 2 3.702,1.056 3.803,1.214 0.100,0.158 10 3 1.991,0.718 2.415,0.888 0.424,0.170 10 STOP 2.062,1.315 2.389,1.485 0.327,0.170 10 IGN 0.75,0.545 1.615,0.733 0.864,0.188 10 from Battery 0.568,1.139 1.582,1.328 1.015,0.188 10 from IG2 Relay 5.169,0.56 5.529,0.743 0.360,0.184 10 STP 5.169,1.164 5.529,1.348 0.360,0.184 10 ST1- 0.096,2.467 3.566,2.626 3.470,0.159 10 *4: for 1GR-FE, 1UR-FE, 3UR-FE, 1VD-FTV (w/o DPF) 0.096,2.181 1.719,2.340 1.623,0.159 10 *3: for 1VD-FTV (w/ DPF) 4.719,0.267 5.050,0.423 0.332,0.156 10 13*3

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
a.

Using the intelligent tester, read the Data List (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
OK
(for 1GR-FE)
A
OK
(for 1UR-FE)
B
OK
(for 3UR-FE)
C
OK
(for 1VD-FTV)
D
NG E



A

B

C

D

E

2.INSPECT STOP LIGHT SWITCH
2.INSPECT STOP LIGHT SWITCH
E164228E01
0.187,0 2.706,0.364 2.519,0.363 10 Component without harness connected: (Stop Light Switch) 1.235,3.822 2.087,4.004 0.852,0.181 10 Pin pushed 0.203,4.06 1.297,4.242 1.094,0.181 10 Pin released

a.

Remove the stop light switch (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin pushed 10 kΩ or higher
Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
Pin not pushed 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)

B

REPLACE STOP LIGHT SWITCH

C

REPLACE STOP LIGHT SWITCH

3.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
U165805E02
0.156,0.073 2.531,0.438 2.375,0.365 10 false Front view of wire harness connector: (to Stop Light Switch) 0.531,1.24 0.802,1.406 0.271,0.167 10 false A30

a.

Disconnect the A30 stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A30-2 - Body ground Always 11 to 14 V
A30-4 - Body ground Ignition switch ON




OK

4.CHECK ENGINE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ENGINE TYPE
a.

Check the engine type.

Engine Type
Engine type Proceed to
for 1GR-FE, 1UR-FE, 3UR-FE, 1VD-FTV (w/o DPF) A
for 1VD-FTV (w/ DPF) B



A

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

B

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E349625E01
0.719,1.073 1.042,1.302 0.323,0.229 3.469,1.198 3.792,1.427 0.323,0.229 3.458,0.844 3.781,1.073 0.323,0.229 5.604,2.01 5.75,1.354 true 6.031,2 5.854,1.354 true 0.385,0.135 2.75,0.542 2.365,0.406 10 false Front view of wire harness connector:(to Stop Light Switch) 0.385,0.135 2.75,0.542 2.365,0.406 10 false Front view of wire harness connector:(to Stop Light Switch) 4.042,0.104 6.406,0.51 2.365,0.406 10 false Front view of wire harness connector:(to ECM) 0.385,0.135 2.75,0.542 2.365,0.406 10 false Front view of wire harness connector:(to Stop Light Switch) 0.771,1.115 1.177,1.365 0.406,0.25 10 false A30 5.406,2.042 5.813,2.292 0.406,0.25 10 false ST1- 3.927,0.927 4.333,1.177 0.406,0.25 10 false *1 3.958,1.208 4.365,1.458 0.406,0.25 10 false *2 6.021,2.021 6.427,2.271 0.406,0.25 10 false STP 0.25,2.146 1.063,2.354 0.813,0.208 10 false *1: for LHD 0.271,2.396 1.042,2.573 0.771,0.177 10 false *2: for RHD 3.5,1.229 3.906,1.479 0.406,0.25 10 false A52 3.49,0.875 3.896,1.125 0.406,0.25 10 false A38

a.

Disconnect the A30 stop light switch connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A30-1 - A38-36 (STP) Always Below 1 Ω
A30-1 - Body ground Always 10 kΩ or higher
A30-3 - A38-35 (ST1-) Always Below 1 Ω
A30-3 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A30-1 - A52-36 (STP) Always Below 1 Ω
A30-1 - Body ground Always 10 kΩ or higher
A30-3 - A52-35 (ST1-) Always Below 1 Ω
A30-3 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK
(for 1GR-FE)
A
OK
(for 1UR-FE)
B
OK
(for 3UR-FE)
C
OK
(for 1VD-FTV, w/o DPF)
D
NG E



A

B

C

D

E

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E349625E02
0.5,1.063 0.854,1.333 0.354,0.271 3.792,1.01 4.146,1.281 0.354,0.271 3.792,1.333 4.146,1.604 0.354,0.271 5.281,2.01 5.76,1.354 true 6.094,2.031 5.781,1.042 true 0.406,0.115 2.729,0.552 2.323,0.438 10 false Front view of wire harness connector:(to Stop Light Switch) 4.427,0.125 6.75,0.563 2.323,0.438 10 false Front view of wire harness connector:(to ECM) 3.865,1.052 4.323,1.25 0.458,0.198 10 false A38 3.854,1.365 4.313,1.563 0.458,0.198 10 false A52 0.542,1.115 1,1.313 0.458,0.198 10 false A30 5.063,2.073 5.521,2.271 0.458,0.198 10 false ST1- 5.99,2.115 6.448,2.313 0.458,0.198 10 false STP 0.417,1.917 1.219,2.135 0.802,0.219 10 false *1: for LHD 0.448,2.25 1.219,2.479 0.771,0.229 10 false *2: for RHD 4.167,1.052 4.625,1.25 0.458,0.198 10 false *1 4.188,1.354 4.646,1.552 0.458,0.198 10 false *2

a.

Disconnect the A30 stop light switch connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A30-1 - A38-13 (STP) Always Below 1 Ω
A30-1 - Body ground Always 10 kΩ or higher
A30-3 - A38-35 (ST1-) Always Below 1 Ω
A30-3 - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A30-1 - A52-13 (STP) Always Below 1 Ω
A30-1 - Body ground Always 10 kΩ or higher
A30-3 - A52-35 (ST1-) Always Below 1 Ω
A30-3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR