Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch assembly signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.

DTC Code DTC Detection Condition Trouble Area
P0571 When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more.
·

Stop light switch assembly

·

Harness or connector

·

ECM



WIRING DIAGRAM

C349538E01
0.204,0.877 1.221,1.181 1.017,0.304 10 from IG Circuit 0.328,0.321 1.165,0.597 0.836,0.276 10 from Battery 1.5,1.014 2.580,1.219 1.080,0.205 10 IG2 NO. 1 1.64,0.475 2.394,0.631 0.753,0.156 10 STOP 2.81,0.356 3.070,0.623 0.260,0.267 10 B 2.81,0.881 3.070,1.148 0.260,0.267 10 B 2.824,1.344 3.279,1.590 0.455,0.246 10 GND 3.469,1.267 3.597,1.458 0.128,0.191 10 L 3.469,0.397 3.597,0.588 0.128,0.191 10 L 5.799,0.395 6.177,0.588 0.378,0.193 10 A38 5.792,1.293 6.170,1.486 0.378,0.193 10 A38 6.362,2.233 6.928,2.452 0.566,0.218 10 ECM 5.875,0.155 5.996,0.293 0.121,0.139 10 7 5.875,1.068 5.996,1.210 0.121,0.142 10 8 6.152,0.39 6.481,0.546 0.330,0.156 10 STP 6.152,1.288 6.509,1.451 0.357,0.163 10 ST1- 5.428,0.402 5.806,0.595 0.378,0.193 10 A38 5.442,1.293 5.820,1.486 0.378,0.193 10 A38 5.472,1.065 5.670,1.210 0.198,0.145 10 35 5.472,0.155 5.670,0.293 0.198,0.139 10 36 5.066,0.402 5.444,0.595 0.378,0.193 10 A38 5.087,0.151 5.292,0.293 0.205,0.142 10 13 5.066,1.294 5.347,1.436 0.281,0.142 10 A52 5.101,1.072 5.299,1.211 0.198,0.139 10 35 4.702,0.398 4.983,0.540 0.281,0.142 10 A52 4.737,0.155 4.934,0.293 0.198,0.139 10 36 4.352,0.398 4.632,0.540 0.281,0.142 10 A52 4.38,0.156 4.582,0.293 0.202,0.137 10 13 5.111,0.633 5.378,0.773 0.267,0.140 10 *4 0.169,3.428 3.760,3.602 3.591,0.174 10 *4: for 1VD-FTV (LHD) 0.169,3.128 4.473,3.311 4.304,0.184 10 *3: for 1GR-FE (LHD), 1UR-FE (LHD) and 1VD-FTV (LHD) 0.169,2.527 1.527,2.725 1.357,0.198 10 *1: for 3UR-FE 0.169,2.827 3.964,3.002 3.795,0.174 10 *2: for 1GR-FE (LHD) and 1UR-FE (LHD) 5.108,1.513 5.292,1.654 0.184,0.141 10 *5 0.169,3.728 4.066,3.890 3.897,0.163 10 *5: for 1GR-FE (RHD), 1UR-FE (RHD) and 1VD-FTV (RHD) 4.745,0.631 4.957,0.773 0.211,0.142 10 *6 5.842,0.627 6.053,0.773 0.211,0.145 10 *1 5.476,0.634 5.653,0.773 0.177,0.139 10 *2 2.362,1.869 4.073,2.101 1.711,0.232 10 Stop light Switch Assembly 2.362,1.715 2.643,1.878 0.281,0.163 10 A73 3.69,1.161 3.866,1.303 0.177,0.142 10 4 3.69,0.265 3.852,0.455 0.163,0.191 10 2 5.844,1.512 6.055,1.654 0.211,0.142 10 *1 5.476,1.512 5.653,1.654 0.177,0.142 10 *3 2.613,0.23 2.852,0.399 0.239,0.170 10 1 2.613,0.748 2.797,0.897 0.184,0.149 10 5 2.613,1.21 2.762,1.380 0.149,0.170 10 3 0.169,4.028 3.973,4.193 3.804,0.165 10 *6: for 1GR-FE (RHD) and 1UR-FE (RHD) 4.38,0.631 4.572,0.773 0.193,0.142 10 *7 0.169,4.328 3.899,4.502 3.730,0.174 10 *7: for 1VD-FTV (RHD)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
U166274E01
0.054,0.019 0.206,0.179 0.151,0.161 10 *a 1.592,0.2 1.861,0.356 0.270,0.156 10 A73 1.1,1.835 1.209,1.991 0.110,0.156 10 B 1.354,1.451 1.164,1.813 false 1.722,1.428 1.748,1.851 false 1.561,1.892 1.912,2.043 0.350,0.151 10 GND 2.319,1.818 2.428,1.973 0.110,0.156 10 B 2.364,1.792 2.126,1.442 false

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-5 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A73-1 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY INPUT CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY INPUT CIRCUIT)
a.

for 3UR-FE:

i.
U166493E02
2.125,1.625 2.51,0.875 2.51,0.875 2.635,0.875 false 1.438,2.885 1.667,2.885 1.667,2.885 1.938,1.688 false 1.677,0.698 1.958,0.875 0.281,0.177 10 false A38 0.135,0.063 0.365,0.25 0.229,0.188 10 false *a 2.688,0.792 3.052,0.958 0.365,0.167 10 false ST1- 1.094,2.802 1.406,2.969 0.313,0.167 10 false STP

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-8 (ST1-) - Body ground Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed 0 to 1.5 V
A38-7 (STP) - Body ground Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



b.

for 1UR-FE (LHD) and 1GR-FE (LHD):

i.
U166494E02
1.448,1.927 1.125,0.875 1.125,0.875 0.969,0.875 false 0.635,2.885 0.865,2.885 0.865,2.885 1.563,1.99 false 1.677,0.698 1.958,0.875 0.281,0.177 10 false A38 0.135,0.063 0.365,0.25 0.229,0.188 10 false *a 0.604,0.792 0.969,0.958 0.365,0.167 10 false ST1- 0.26,2.813 0.573,2.979 0.313,0.167 10 false STP

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-35 (ST1-) - Body ground Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed 0 to 1.5 V
A38-36 (STP) - Body ground Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



c.

for 1UR-FE (RHD) and 1GR-FE (RHD):

i.
U166495E02
1.448,1.917 1.125,0.865 1.125,0.865 0.969,0.865 false 0.625,2.885 0.854,2.885 0.854,2.885 1.552,1.99 false 1.677,0.698 1.948,0.844 0.271,0.146 10 false A52 0.135,0.063 0.365,0.25 0.229,0.188 10 false *a 0.563,0.802 0.927,0.969 0.365,0.167 10 false ST1- 0.219,2.823 0.531,2.99 0.313,0.167 10 false STP

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-35 (ST1-) - Body ground Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed 0 to 1.5 V
A52-36 (STP) - Body ground Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



d.

for 1VD-FTV (LHD):

i.
U166496E02
1.458,1.927 1.135,0.875 1.135,0.875 0.979,0.875 false 2.531,2.885 2.75,2.885 2.75,2.885 2.76,1.667 false 1.677,0.698 1.948,0.844 0.271,0.146 10 false A38 0.135,0.063 0.365,0.25 0.229,0.188 10 false *a 0.625,0.781 0.99,0.948 0.365,0.167 10 false ST1- 2.229,2.813 2.542,2.979 0.313,0.167 10 false STP

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-35 (ST1-) - Body ground Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed 0 to 1.5 V
A38-13 (STP) - Body ground Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



e.

for 1VD-FTV (RHD):

i.
U166497E02
1.448,1.917 1.125,0.865 1.125,0.865 0.969,0.865 false 2.563,2.896 2.729,2.896 2.729,2.896 2.729,1.667 false 1.698,0.698 1.979,0.875 0.281,0.177 10 false A52 0.135,0.063 0.365,0.25 0.229,0.188 10 false *a 0.646,0.771 1.01,0.938 0.365,0.167 10 false ST1- 2.24,2.823 2.552,2.99 0.313,0.167 10 false STP

Disconnect the ECM connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-35 (ST1-) - Body ground Ignition switch ON, brake pedal released 7.5 to 14 V
Ignition switch ON, brake pedal depressed 0 to 1.5 V
A52-13 (STP) - Body ground Brake pedal released 0 to 1.5 V
Brake pedal depressed 7.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)




OK

3.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Temporarily replace the stop light switch assembly with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Cruise Control / Trouble Codes.



g.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON/OFF).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.




Result:
Result Proceed to
DTC P0571 is not output A
DTC P0571 is output (for 1GR-FE) B
DTC P0571 is output (for 1VD-FTV) C
DTC P0571 is output (for 1UR-FE) D
DTC P0571 is output (for 3UR-FE) E



A

END (STOP LIGHT SWITCH ASSEMBLY WAS DEFECTIVE)

B

C

D

E