When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels control of vehicle speed by the cruise control system. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light switch assembly signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake pedal is depressed, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM cancels control of vehicle speed by the cruise control system.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0571 | When voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for 0.5 seconds or more. | ·
Stop light switch assembly ·
Harness or connector ·
ECM |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-3 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A73-5 (B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Engine switch off | Below 1 V | |
| A73-1 (B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
OK
NG
for 3UR-FE:
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-8 (ST1-) - Body ground | Engine switch on (IG), brake pedal released | 7.5 to 14 V |
| Engine switch on (IG), brake pedal depressed | 0 to 1.5 V | |
| A38-7 (STP) - Body ground | Brake pedal released | 0 to 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
for 1UR-FE (LHD):
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-35 (ST1-) - Body ground | Engine switch on (IG), brake pedal released | 7.5 to 14 V |
| Engine switch on (IG), brake pedal depressed | 0 to 1.5 V | |
| A38-36 (STP) - Body ground | Brake pedal released | 0 to 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
for 1UR-FE (RHD):
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-35 (ST1-) - Body ground | Engine switch on (IG), brake pedal released | 7.5 to 14 V |
| Engine switch on (IG), brake pedal depressed | 0 to 1.5 V | |
| A52-36 (STP) - Body ground | Brake pedal released | 0 to 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
for 1VD-FTV (LHD):
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-35 (ST1-) - Body ground | Engine switch on (IG), brake pedal released | 7.5 to 14 V |
| Engine switch on (IG), brake pedal depressed | 0 to 1.5 V | |
| A38-13 (STP) - Body ground | Brake pedal released | 0 to 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
for 1VD-FTV (RHD):
Disconnect the ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-35 (ST1-) - Body ground | Engine switch on (IG), brake pedal released | 7.5 to 14 V |
| Engine switch on (IG), brake pedal depressed | 0 to 1.5 V | |
| A52-13 (STP) - Body ground | Brake pedal released | 0 to 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Temporarily replace the stop light switch assembly with a new or normally functioning one (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Radar Cruise 1/ Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Drive the vehicle at a speed for which cruise control operation is possible.
Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).
Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR ).
| Result | Proceed to |
|---|---|
| DTC P0571 is not output | A |
| DTC P0571 is output (for 1UR-FE) | B |
| DTC P0571 is output (for 3UR-FE) | C |
| DTC P0571 is output (for 1VD-FTV) | D |
A
B
C
D