Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  U1102  Lost Communication with Radar Sensor  


DESCRIPTION

The distance control ECU sends the vehicle speed and estimated curve information to the millimeter wave radar sensor. The millimeter wave radar sensor sends information about whether another vehicle is present in front of the vehicle, the distance between the vehicles, relative speed, etc. to the distance control ECU. The distance control ECU sends this information to the ECM and performs control of cruise control.

DTC Code DTC Detection Condition Trouble Area
U1102 The vehicle speed is 50 km/h (30 mph) or more with the cruise control main switch on (vehicle-to-vehicle distance control mode) and the data sent from the distance control ECU to the millimeter wave radar sensor is abnormal.
·

Distance control ECU

·

Harness or connector

·

Millimeter wave radar sensor



WIRING DIAGRAM

E149026E04
0.677,2.281 2.708,2.594 2.031,0.313 10 false Millimeter Wave Radar Sensor 4.906,2.448 6.375,2.708 1.469,0.26 10 false Distance Control ECU 1.979,0.646 2.49,1 0.51,0.354 10 false IGB 1.875,0.979 2.594,1.354 0.719,0.375 10 false LRRD 1.875,1.302 2.563,1.729 0.688,0.427 10 false LRDD 1.854,1.667 2.615,2.042 0.76,0.375 10 false SGND 4.979,0.667 5.552,0.99 0.573,0.323 10 false IGB 4.979,0.99 5.594,1.344 0.615,0.354 10 false LRRD 4.979,1.333 5.594,1.677 0.615,0.344 10 false LRDD 4.979,1.646 5.927,2.167 0.948,0.521 10 false SGND 2.333,0.552 2.625,0.844 0.292,0.292 10 false 5 2.333,1.552 2.854,1.927 0.521,0.375 10 false 2 2.333,1.219 2.802,1.573 0.469,0.354 10 false 3 2.333,0.896 2.479,1.052 0.146,0.156 10 false 4 4.677,0.531 4.958,0.771 0.281,0.24 10 false 13 4.688,0.885 5.146,1.281 0.458,0.396 10 false 23 4.688,1.229 5.094,1.563 0.406,0.333 10 false 22 4.688,1.573 5.146,1.906 0.458,0.333 10 false 10 0.708,2.094 1.01,2.323 0.302,0.229 10 false A56 4.917,2.292 5.385,2.51 0.469,0.219 10 false E108

CAUTION / NOTICE / HINT

NOTICE:
·

When the distance control ECU is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DISTANCE CONTROL ECU>INITIALIZATION).

·

When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

As it is possible that this DTC was stored due to a bad connection of a connector, make sure to check that each connector is connected securely.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - MILLIMETER WAVE RADAR SENSOR)
a.

Disconnect the A56 millimeter wave radar sensor connector.

E349644E02
4.854,0.573 5.208,0.823 0.354,0.25 0.313,1.458 0.667,1.708 0.354,0.25 1.104,2 1.385,1.563 true 1.698,2.115 1.625,1.573 true 4.438,2.125 4.865,1.76 true 4.844,2.323 4.906,1.854 true 0.354,1.5 0.813,1.698 0.458,0.198 10 false A56 0.469,0.125 2.833,0.646 2.365,0.521 10 false Front view of wire harness connector: (to Millimeter Wave Radar Sensor) 3.969,0.094 6.292,0.604 2.323,0.51 10 false Rear view of wire harness connector: (to Distance Control ECU) 0.875,2.042 1.333,2.24 0.458,0.198 10 false SGND 1.542,2.156 2,2.354 0.458,0.198 10 false LRDD 4.875,0.615 5.333,0.813 0.458,0.198 10 false E108 3.99,2.052 4.448,2.25 0.458,0.198 10 false SGND 4.667,2.365 5.125,2.563 0.458,0.198 10 false LRDD


b.

Disconnect the E108 distance control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-3 (LRDD) - E108-22 (LRDD) Always Below 1 Ω
E108-22 (LRDD) - Body ground Always 10 kΩ or higher
A56-2 (SGND) - Body ground Always 10 kΩ or higher
E108-10 (SGND) - Body ground




OK

2.REPLACE DISTANCE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE DISTANCE CONTROL ECU
a.

Replace the distance control ECU with a new one (See page Engine / Hybrid System>CRUISE CONTROL>DISTANCE CONTROL ECU>REMOVAL).




NEXT

3.CHECK DTC (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
3.CHECK DTC (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
a.

Using the intelligent tester, enter the following menus: Powertrain / Radar Cruise / Trouble Code.



c.

Perform the following to make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


i.

Drive the vehicle at a speed of 50 km/h (30 mph) or more.


ii.

Turn the cruise control main switch on.


iii.

Push the -SET switch to activate the dynamic radar cruise control.



d.


OK

END (DISTANCE CONTROL ECU IS DEFECTIVE)

NG