Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Millimeter Wave Radar Sensor Power Source Circuit  


DESCRIPTION

This circuit provides power to the millimeter wave radar sensor. The millimeter wave radar sensor emits radio waves towards an object in front and measures the distance and direction of the object by receiving the wave reflections. Based on the reflections, the sensor calculates the difference in speed between the vehicle and the object in front. This data is transmitted to the distance control ECU.

WIRING DIAGRAM

E158908E04
0.646,3.177 2.563,3.427 1.917,0.25 10 false Millimeter Wave Radar Sensor 1.177,1.604 1.469,1.792 0.292,0.188 10 false IGB 5.677,1.594 6.125,1.781 0.448,0.188 10 false IGB 5.406,1.5 5.604,1.646 0.198,0.146 10 false 13 1.573,1.469 1.781,1.656 0.208,0.188 10 false 5 3.156,0.667 3.594,0.854 0.438,0.188 10 false LGND 1.073,0.677 1.51,0.865 0.438,0.188 10 false LGND 1.563,0.531 1.771,0.719 0.208,0.188 10 false 1 2.906,0.552 3.115,0.74 0.208,0.188 10 false 44 1.021,2.469 1.469,2.656 0.448,0.188 10 false SGND 5.698,2.458 6.146,2.646 0.448,0.188 10 false SGND 5.406,2.344 5.604,2.49 0.198,0.146 10 false 10 1.573,2.333 1.781,2.521 0.208,0.188 10 false 2 0.646,3 0.927,3.167 0.281,0.167 10 false A56 0.229,3.573 0.979,3.802 0.75,0.229 10 false *2: for RHD 0.229,3.385 0.979,3.604 0.75,0.219 10 false *1: for LHD 5.5,3.177 6.906,3.479 1.406,0.302 10 false Distance Control ECU 5.5,3.01 5.875,3.188 0.375,0.177 10 false E108 3.177,1.448 3.813,1.698 0.635,0.25 10 false ECM 3.177,1.281 3.646,1.458 0.469,0.177 10 false A52*2 3.177,1.115 3.646,1.292 0.469,0.177 10 false A38*1

CAUTION / NOTICE / HINT

NOTICE:

When the distance control ECU is replaced with a new one, initialization must be performed (See page Engine / Hybrid System>CRUISE CONTROL>DISTANCE CONTROL ECU>INITIALIZATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DISTANCE CONTROL ECU)
a.

Disconnect the A56 millimeter wave radar sensor connector.

E349649E01
0.344,1.104 0.698,1.344 0.354,0.24 3.948,1.635 4.344,1.885 0.396,0.25 1.031,1.854 1.448,1.438 true 4.229,2.115 4.927,1.99 true 6.323,1.792 5.885,2.063 true 0.375,0.083 2.729,0.573 2.354,0.49 10 false Front view of wire harness connector: (to Millimeter Wave Radar Sensor) 4.292,0.073 6.646,0.563 2.354,0.49 10 false Rear view of wire harness connector: (to Distance Control ECU) 0.396,1.146 0.854,1.344 0.458,0.198 10 false A56 0.708,1.865 1.167,2.063 0.458,0.198 10 false SGND 2.208,1.854 2.667,2.052 0.458,0.198 10 false IGB 3.99,1.677 4.448,1.875 0.458,0.198 10 false E108 3.781,2.031 4.24,2.229 0.458,0.198 10 false SGND 6.365,1.729 6.823,1.927 0.458,0.198 10 false IGB


b.

Disconnect the E108 distance control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A56-2 (SGND) - E108-10 (SGND) Always Below 1 Ω
A56-5 (IGB) - E108-13 (IGB)
E108-13 (IGB) - Body ground Always 10 kΩ or higher
A56-5 (IGB) - Body ground




OK

2.CHECK DISTANCE CONTROL ECU (IGB VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DISTANCE CONTROL ECU (IGB VOLTAGE)
a.
U166018E01
2.06,2.188 2.529,2.761 false 1.384,2.192 1.121,2.788 false 0.254,0.03 2.743,0.642 2.488,0.612 10 Front view of wire harness connector: (to Millimeter Wave Radar Sensor) 2.474,2.793 2.817,2.963 0.343,0.170 10 IGB 0.814,2.801 1.252,2.971 0.438,0.170 10 SGND 1.498,1.15 1.779,1.296 0.282,0.146 10 A56

Disconnect the A56 millimeter wave radar sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A56-5 (IGB) - A56-2 (SGND) Engine switch on (IG) 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - ECM AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - ECM AND BODY GROUND)
a.

Disconnect the A56 millimeter wave radar sensor connector.

E349650E01
1.073,1.188 1.438,1.458 0.365,0.271 5.333,0.385 5.698,0.656 0.365,0.271 6.313,0.396 6.677,0.667 0.365,0.271 1.698,1.76 2.115,1.344 true 5.979,2.271 6.198,1.688 true 1.115,1.24 1.573,1.438 0.458,0.198 10 false A56 0.656,0.094 3,0.635 2.344,0.542 10 false Front view of wire harness connector: (to Millimeter Wave Radar Sensor) 4.063,0.083 6.406,0.448 2.344,0.365 10 false Front view of wire harness connector: (to ECM) 5.396,0.458 5.854,0.656 0.458,0.198 10 false A38 6.698,0.469 7.156,0.667 0.458,0.198 10 false *2 5.74,0.448 6.198,0.646 0.458,0.198 10 false *1 6.375,0.469 6.833,0.667 0.458,0.198 10 false A56 1.563,1.802 2.021,2 0.458,0.198 10 false LGND 5.823,2.323 6.281,2.521 0.458,0.198 10 false LGND 0.24,2.073 1.083,2.292 0.844,0.219 10 false *1: for LHD 0.26,2.344 1.177,2.542 0.917,0.198 10 false *2: for RHD


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A56-1 (LGND) - A38-44 (LGND) Always Below 1 Ω
A56-1 (LGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A56-1 (LGND) - A52-44 (LGND) Always Below 1 Ω
A56-1 (LGND) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR