Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Washer Signal Circuit  


DESCRIPTION

The distance control ECU detects washer operation. Cruise control will be canceled by the distance control ECU if the windshield wipers operate in HI or LO mode.

WIRING DIAGRAM

E158906E03
5.129,2.136 6.535,2.315 1.406,0.179 10 Distance Control ECU 5.129,1.972 5.489,2.123 0.361,0.150 10 E108 0.572,1.952 2.191,2.131 1.619,0.179 10 Windshield Wiper Switch 3.136,0.704 4.756,0.985 1.620,0.281 10 to Front Washer Motor 0.572,1.788 0.863,1.961 0.291,0.173 10 E15 5.509,1.209 5.979,1.400 0.471,0.191 10 WASH 1.283,1.209 1.542,1.400 0.258,0.191 10 WF 5.267,1.113 5.407,1.258 0.141,0.145 10 3 1.664,1.113 1.919,1.258 0.255,0.145 10 1*2 1.664,0.967 1.919,1.112 0.255,0.145 10 3*1 0.089,2.272 0.869,2.418 0.780,0.145 10 *1: for LHD 0.089,2.543 0.869,2.689 0.780,0.145 10 *2: for RHD

PROCEDURE

1.CHECK WASHER MOTOR (OPERATION)
a.

Check that the front washer operates (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM(w/ Rain Sensor)>Washer Motor Circuit).

OK:

Washer function is normal.




OK

2.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - WINDSHIELD WIPER SWITCH)

NG

2.CHECK HARNESS AND CONNECTOR (DISTANCE CONTROL ECU - WINDSHIELD WIPER SWITCH)
a.

Disconnect the E108 distance control ECU connector.

E349660E01
0.542,2.344 0.938,2.625 0.396,0.281 5.448,0.823 5.844,1.104 0.396,0.281 2.292,2.458 2.656,3.01 true 5.979,1.677 6.406,1.448 true 4.875,1.542 5.406,1.677 true 0.583,2.406 1.198,2.604 0.615,0.198 10 false E108 0.292,0.135 2.573,0.698 2.281,0.563 10 false Rear view of wire harness connector: (to Distance Control ECU) 4.583,0.125 6.885,0.656 2.302,0.531 10 false Front view of wire harness connector: (to Windshield Wiper Switch) 5.521,0.865 5.979,1.115 0.458,0.25 10 false E15 2.708,2.938 3.323,3.135 0.615,0.198 10 false WASH 4.469,1.458 5.083,1.656 0.615,0.198 10 false WF*2 4.302,2.969 5.24,3.177 0.938,0.208 10 false *1: for LHD 4.323,3.365 5.24,3.615 0.917,0.25 10 false *2: for RHD 6.469,1.344 7.083,1.542 0.615,0.198 10 false WF*1


b.

Disconnect the E15 windshield wiper switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E108-3 (WASH) - E15-3 (WF) Always Below 1 Ω
E15-3 (WF) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E108-3 (WASH) - E15-1 (WF) Always Below 1 Ω
E15-1 (WF) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR