Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM(w/ Rain Sensor) › 2014.08–2015.08
RM2660E _59 Vehicle Exterior _052854 WIPER / WASHER _0255769 WIPER AND WASHER SYSTEM(w/ Rain Sensor) J

WIPER / WASHER  WIPER AND WASHER SYSTEM(w/ Rain Sensor)  Washer Motor Circuit  


DESCRIPTION

The windshield wiper ECU receives washer switch information from the front wiper switch, and operates the washer motor.

WIRING DIAGRAM

E159009E03
5.479,4.115 7.073,4.323 1.594,0.208 10 false Windshield Wiper Switch 3.667,0.75 3.865,0.938 0.198,0.188 10 false 1 4.563,0.75 4.76,0.969 0.198,0.219 10 false 2 5.719,0.646 6.042,0.865 0.323,0.219 10 false E15 3.385,0.99 3.719,1.208 0.333,0.219 10 false A16 5.719,0.417 6.021,0.604 0.302,0.188 10 false 3 3.385,1.208 4.969,1.375 1.583,0.167 10 false Front Washer Motor 6.094,0.646 6.396,0.823 0.302,0.177 10 false WF 1.104,0.646 1.979,0.823 0.875,0.177 10 false from Battery 5.708,3.563 5.969,3.74 0.26,0.177 10 false E16 6.052,3.583 6.323,3.76 0.271,0.177 10 false EW 5.708,0.25 5.865,0.427 0.156,0.177 10 false 1 5.813,0.417 5.969,0.594 0.156,0.177 10 false *1 5.802,0.25 5.958,0.427 0.156,0.177 10 false *2 0.083,4.052 1,4.229 0.917,0.177 10 false *1: for LH Side 0.094,4.281 1.042,4.458 0.948,0.177 10 false *2: for RH Side 5.781,3.333 5.938,3.51 0.156,0.177 10 false 2

PROCEDURE

1.INSPECT FRONT WASHER MOTOR
a.
E147180E01
0.157,0 2.683,0.422 2.527,0.422 10 Component without harness connected: (Front Washer Motor)

Remove the front washer motor (See page Vehicle Exterior>WIPER / WASHER>WASHER MOTOR (for Front Side)>REMOVAL).


b.

Apply battery voltage to the windshield washer motor and check the operation of the windshield washer motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 1
Battery negative (-) → Terminal 2
Front washer motor operation is normal




OK

2.CHECK HARNESS AND CONNECTOR (FRONT WASHER MOTOR - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (FRONT WASHER MOTOR - BODY GROUND)
a.
U166023E02
0.313,0.031 2.635,0.375 2.323,0.344 10 false Front view of wire harness connector: (to Front Washer Motor) 2.604,1.375 2.885,1.552 0.281,0.177 10 false A16

Disconnect the A16 front washer motor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A16-1 - Body ground Always 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH - BODY GROUND)
a.
U166024E01
0.291,0.039 2.668,0.387 2.378,0.348 10 Front view of wire harness connector: (to Windshield Wiper Switch) 2.584,1.023 2.849,1.204 0.264,0.181 10 E16 0.915,0.927 1.223,1.109 0.308,0.181 10 EW 1.219,1.001 1.661,1.321 false

Disconnect the E16 windshield wiper switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E16-2 - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (FRONT WASHER MOTOR - WINDSHIELD WIPER SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT WASHER MOTOR - WINDSHIELD WIPER SWITCH)
a.

Disconnect the E15 windshield wiper switch connector.

E349750E01
2.792,1.448 3.24,1.698 0.448,0.25 6.313,1.667 6.76,1.917 0.448,0.25 0.979,1.333 1.885,1.594 true 1.021,1.75 1.531,1.677 true 0.156,0.083 2.469,0.552 2.313,0.469 10 false Front view of wire harness connector: (to Windshield Wiper Switch) 4.24,0.063 6.552,0.531 2.313,0.469 10 false Front view of wire harness connector: (to Front Washer Motor) 0.615,1.667 1.229,1.865 0.615,0.198 10 false WF*2 2.896,1.49 3.51,1.688 0.615,0.198 10 false E15 0.594,1.25 1.208,1.448 0.615,0.198 10 false WF*1 3.76,2.115 4.823,2.344 1.063,0.229 10 false *1: for LH Side 3.781,2.448 4.781,2.677 1,0.229 10 false *2: for RH Side 6.438,1.698 6.813,1.917 0.375,0.219 10 false A16


b.

Disconnect the A16 washer motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
A16-2 - E15-3 (WF) Always Below 1 Ω
A16-2 - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
A16-2 - E15-1 (WF) Always Below 1 Ω
A16-2 - Body ground Always 10 kΩ or higher




OK

REPLACE WINDSHIELD WIPER SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR