Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  P1578  Brake System  


DESCRIPTION

This DTC is output when the vehicle stability control system has a problem. Check the vehicle stability control system when this DTC is output.

DTC No. DTC Detection Condition Trouble Area
P1578 The ECM receives a brake system error signal for 0.2 sec. or more while the cruise control is operating.
·

Vehicle stability control system

·

Skid control ECU (master cylinder solenoid)

·

ECM



CAUTION / NOTICE / HINT

HINT:

This circuit uses CAN communication. Therefore, if there are any malfunctions in the communication circuit, one or more DTCs in the CAN communication system are output.


PROCEDURE

1.CHECK FOR DTCs (ABS/VSC/TRAC)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK DTC OUTPUT (RADAR CRUISE1)

B

2.CHECK DTC OUTPUT (RADAR CRUISE1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed by the cruise control system.



e.

Enter the following menus: Powertrain / Cruise Control / Trouble Codes.


f.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC P1578 is not output A
DTC P1578 is output B




A

B

3.REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)
3.REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)

Replace the skid control ECU (master cylinder solenoid).



NEXT

4.CHECK DTC OUTPUT (RADAR CRUISE1)
4.CHECK DTC OUTPUT (RADAR CRUISE1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which cruise control operation is possible.


ii.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed by the cruise control system.



e.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC P1578 is not output A
DTC P1578 is output (for 1UR-FE) B
DTC P1578 is output (for 3UR-FE) C
DTC P1578 is output (for 1VD-FTV) D




A

END

B

C

D