Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255253 MILLIMETER WAVE RADAR SENSOR N

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  ADJUSTMENT  


PROCEDURE

Hide 88211B 1.PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT

a.
E332928E04
0.25,0.969 0.479,1.188 0.229,0.219 10 false *a 1.01,0.125 1.24,0.344 0.229,0.219 10 false *c 1.906,0.146 2.135,0.365 0.229,0.219 10 false *d 1.292,1.906 1.521,2.125 0.229,0.219 10 false *b

Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.

Text in Illustration
*a 5 m (16.4 ft.)
*b 6 m (19.7 ft.)
*c 4 m (13.1 ft.)
*d 2 m (6.56 ft.)
V100144

Do not place any metal objects in this area
V100155

Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area

HINT:

Metal objects with a height of 50 mm (1.97 in.) or less placed within the area shown in the illustration will not affect the adjustment.



b.

Adjust the tire inflation pressure to the specified pressure. (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION)


c.

Clean the radiator grille emblem or millimeter wave radar sensor assembly.


d.

Visually inspect the front of the vehicle.

HINT:

Confirm that there is no damage or deformation.



e.

Visually inspect the front bumper assembly, radiator grille and stays.

HINT:

Confirm that there is no damage or deformation.



Hide 88211B 2.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY

a.

Adjust SST (reflector) height.

i.
C320141E06
1.719,0.865 2.115,0.656 2.115,0.656 1.458,0.688 false 2.198,0.552 2.354,0.698 0.156,0.146 10 false *a

Adjust SST (reflector) so that the center of SST (reflector) is the same height as the millimeter wave radar sensor.

HINT:

Make sure to align the center of SST (reflector) with the millimeter wave radar sensor (the center of the radiator grille emblem).


Text in Illustration
*a SST (reflector)

Reference Value:

950 mm (3.12 ft.)


SST
09870-60000  (09870-60010)
09870-60040  



b.

Place SST (reflector).

i.

Hang a weight with a pointed tip from the center of the symbol emblem, and mark the rear center point of the vehicle (point A) on the ground.

E332923E02
2.79,2.602 3.016,2.39 3.016,2.39 3.251,2.39 false 5.16,1.11 5.526,0.656 5.526,0.656 5.878,0.656 false 2.303,2.497 2.504,2.712 0.201,0.215 10 A 3.271,2.323 3.472,2.538 0.201,0.215 10 *b 5.453,1.587 5.654,1.802 0.201,0.215 10 *a 5.885,0.587 6.086,0.802 0.201,0.215 10 *c 2.742,2.695 2.6,2.57 2.6,2.57 2.416,2.57 false 5.158,1.658 5.442,1.658 false

Text in Illustration
*a String *b Weight
*c Center - -

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



ii.

Hang a weight with a pointed tip from the center of the radiator grille emblem, and mark the front center point of the vehicle (point B) on the ground.

E332924E04
1.563,1.573 1.823,1.573 false 1.552,0.417 2.875,0.417 false 3.885,2.271 3.646,2.271 false 4.146,2.365 3.927,2.365 false 1.833,1.469 2.115,1.698 0.281,0.229 10 false *a 3.49,2.188 3.771,2.417 0.281,0.229 10 false *b 4.167,2.26 4.354,2.49 0.188,0.229 10 false B 2.896,0.313 3.177,0.542 0.281,0.229 10 false *c

Text in Illustration
*a String *b Weight
*c Center - -

HINT:

Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.



iii.

Using tape and a string, create a line that connects point B to point A and extends at least 3000 mm (9.84 ft.) beyond the front center point of the vehicle.

E332929E03
0.24,1.594 0.24,1.833 false 0.698,1.49 0.698,1.719 false 6.604,1.594 6.604,1.875 false 0.625,1.75 0.948,2.042 0.323,0.292 10 false *a 0.177,1.854 0.5,2.146 0.323,0.292 10 false *b 1.958,0.167 2.281,0.458 0.323,0.292 10 false *c 0.99,1.271 1.313,1.563 0.323,0.292 10 false C 2.771,1.271 3.094,1.563 0.323,0.292 10 false B 6.354,1.292 6.677,1.583 0.323,0.292 10 false A 6.563,1.875 6.833,2.104 0.271,0.229 10 false *b

Text in Illustration
*a String *b Tape
*c 3000mm (9.84 ft.) - -

HINT:
·

Make sure the string is taut when securing it with tape.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




iv.

Mark point C (SST (reflector) placement position) at a position 3000 mm (9.84 ft.) from point B.


v.

Place SST (reflector) at point C.



c.

Front Beam Axis Adjustment:

NOTICE:
·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not turn off the GTS or engine switch.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Close all of the doors.



i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on and turn the cruise control main switch on.


iv.

Enter the following menus:

Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Adjustment


v.

According to the display on the GTS, press "Next".


vi.

Perform the adjustment according to the display on the GTS.

NOTICE:

If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.


Error No. Error Description Cause of Error Action to be Taken
1 No target abnormality
·

The reflector is placed incorrectly.

·

The radiator grille emblem or millimeter wave radar sensor assembly is covered by dirt or snow.

·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
Clean the radiator grille emblem or millimeter wave radar sensor assembly.
Check the installation condition of the front bumper assembly and radiator grille
Manually change the beam axis. (See page 3. MANUALLY CHANGE BEAM AXIS OF MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
2 Target distance abnormality The reflector is placed incorrectly. Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
3 Plural targets abnormality
·

There is a reflective object near the reflector.

·

A person entered the adjustment area.


Remove any reflective objects.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
4 Target move abnormality
·

The reflector was moved out of position or shaking during the adjustment due to wind.

·

A person entered the adjustment area.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
Perform adjustment in an area with no wind.
Ensure that nobody enters the adjustment area during the adjustment. (See page 1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT)
5 Motor stop Operation of the millimeter wave radar sensor assembly (motor) is abnormal. Turn the engine switch off then on (IG). (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (c) Front Beam Axis Adjustment)
Check for DTCs. (See page (Click here))
6 Target angle abnormality
·

The reflector is placed incorrectly.

·

The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range.


Place the reflector in the correct position. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (b) Place the reflector)
Check the condition of the sensor, radiator grille and front bumper.
7 Radar abnormality Operation of the millimeter wave radar sensor assembly is abnormal. Check for DTCs. (See page (Click here))
8 Radar dirtiness There is dirt on the radiator grille emblem or millimeter wave radar sensor assembly. Clean the radiator grille emblem or millimeter wave radar sensor assembly.
9 Temperature abnormality The temperature around the millimeter wave radar sensor assembly is too high. Wait until the temperature drops to the operable range (-30 to 50°C).
10 Voltage abnormality IG engine source voltage is outside the operable range of the millimeter wave radar sensor assembly. Check the battery voltage (specified condition: 10 to 16 V).
for 1UR-FE: (See page (Click here))
for 3UR-FE: (See page(Click here) )
for 1GR-FE: (See page (Click here))
for 1VD-FTV: (See page (Click here))
11 External communication abnormality CAN communication between DSS and the millimeter wave radar sensor assembly is abnormal. Check the condition of the connectors.
12 Radar axis aiming failure upward The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (upward). Check the installation condition of the front bumper assembly and radiator grille.
Manually change the beam axis. (See page 3. MANUALLY CHANGE BEAM AXIS OF MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
13 Radar axis aiming failure downward The beam axis of the millimeter wave radar sensor assembly is outside the automatic correction range (downward). Check the installation condition of the front bumper assembly and radiator grille.
Manually change the beam axis. (See page 3. MANUALLY CHANGE BEAM AXIS OF MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
14 Vehicle speed abnormality The vehicle is not stationary. Ensure that the vehicle remains stationary.
15 Other
·

A mode change error occurred.

·

Operation of the yaw rate sensor is abnormal.

·

The vehicle is shaking.


Perform adjustment again. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (c) Front Beam Axis Adjustment)
Check for DTCs. (See page (Click here))
Ensure that the vehicle remains stationary.
16 Time out
·

The vehicle cannot communicate with GTS normally.

·

The vehicle does not keep still during beam axis adjustment.

·

Operation of the millimeter wave radar sensor assembly is abnormal.


·

Ensure that the vehicle is connected with the GTS correctly.

·

Ensure that the vehicle remains stationary.

·

Perform beam axis adjustment again and replace the millimeter wave radar sensor assembly if the same error code is output.




vii.

Press the "Exit" button to finish beam axis adjustment.



d.

Front Beam Axis Misalignment Reading:

NOTICE:
·

Ensure that nobody enters the adjustment area during the adjustment.

·

Do not turn off the GTS or engine switch.

·

Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).

·

Close all of the doors.



i.

Enter the following menus:

Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Misalignment Reading


ii.

According to the display on the GTS, press "Next".


iii.

Perform the adjustment according to the display on the GTS.

Specified Condition:
Vertical -0.5 to 0.5 deg
Horizontal -0.6 to 0.6 deg

NOTICE:

If the result is not as specified, perform beam axis adjustment again.




e.

Front Beam Axis Offset Reading:

i.

Enter the following menus:

Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Offset Reading


ii.

According to the display on the GTS, press "Next".


iii.

Perform the adjustment according to the display on the GTS.

Specified Condition:
Vertical learning value 0 deg
Horizontal learning value 0 deg

NOTICE:

If the result is not as specified, perform beam axis adjustment again.



iv.

Turn the engine switch off.


v.

Disconnect the GTS from the DLC3.



Hide 88211B 3. MANUALLY CHANGE BEAM AXIS OF MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NOTICE:
·

Manually change the beam axis when error code 12 (radar axis aiming failure upward), 13 (radar axis aiming failure downward) or 1 (no target abnormality) is displayed.

·

If the beam axis change mechanism is in the most upward or downward position, check for DTCs.

·

If no DTCs are output, repair or correctly install the front bumper assembly.



HINT:

The millimeter wave radar sensor assembly is fixed to the front bumper assembly. If the installation position of the front bumper assembly is misaligned, the beam axis will also be misaligned. Therefore, when the front bumper assembly is deformed, even if the millimeter wave radar sensor assembly beam axis is manually changed or the millimeter wave radar sensor assembly is replaced, the millimeter wave radar sensor assembly beam axis adjustment may not complete.


a.

Remove the upper radiator support seal. (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)


b.

Turn the bolt to change the beam axis of the millimeter wave radar sensor assembly.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

NOTICE:

The beam axis change mechanism may be damaged if torque exceeding the specified amount is applied.


E332930E01
4.882,0.084 5.100,0.305 0.218,0.221 10 *a 4.877,1.284 5.096,1.505 0.218,0.221 10 *b 4.882,2.522 5.100,2.742 0.218,0.221 10 *c

Text in Illustration
*a Standard Position *b Most Downward Position
*c Most Upward Position - -

Vertical axis change Upward direction: Turn screwdriver to negative (-) side
Downward direction: Turn screwdriver to positive (+) side

HINT:
·

Make sure to set the beam axis to the most upward or downward position.

·

Manually change the beam axis to the position *b (most downward position) when error code 12 (radar axis aiming failure upward) is displayed.

·

Manually change the beam axis to the position *c (most upward position) when error code 13 (radar axis aiming failure downward) is displayed.




c.

Perform Front Beam Axis Adjustment. (See page 2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY (c) Front Beam Axis Adjustment)


d.

Install the upper radiator support seal (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>INSTALLATION).