Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER(for Standard) › from 2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255835 FRONT BUMPER(for Standard) A

EXTERIOR PANELS / TRIM  FRONT BUMPER(for Standard)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS

·

w/ Dynamic Radar Cruise Control System:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

Hide 52521 1.INSTALL FRONT BUMPER UPPER CENTER RETAINER

a.

Attach the guide to install the front bumper upper center retainer.


b.

Install the 3 bolts.


Hide 81110 3.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52116A 4.INSTALL FRONT BUMPER SIDE SUPPORT LH

a.

Attach the 3 claws to install the front bumper side support LH.


b.

Install the 2 screws.


Hide 52115A 5.INSTALL FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52026B 6.INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY LH

a.

Install the front bumper No. 2 extension sub-assembly LH with the 4 nuts.

Torque:
67 N*m (683 kgf*cm, 49 ft.*lbf)


Hide 52025B 7.INSTALL FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52021 8.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper reinforcement sub-assembly with the 8 nuts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)


Hide 52611 9.INSTALL FRONT BUMPER ENERGY ABSORBER

a.

Install the front bumper energy absorber.


Hide 52119A 10.INSTALL FRONT BUMPER COVER

HINT:

For the front bumper cover with garnish, use the procedure described below.


a.

w/ Dynamic Radar Cruise Control System:

Connect the connector.


b.

w/ Multi-terrain Monitor:

Connect the connector.


c.

w/ Headlight Cleaner System:

Connect the headlight cleaner hose.


d.

w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:

Connect the No. 4 engine room wire connector.


e.

Attach the 6 claws to install the front bumper cover.


f.

Install the 3 clips, 5 screws and 4 bolts.


g.

Using a T30 "TORX" socket, install the 6 screws.


Hide 53182 11.INSTALL HEADLIGHT COVER LH (w/ Headlight Cover)

a.

Attach the 5 claws and headlight cover LH.


Hide 53181 12.INSTALL HEADLIGHT COVER RH (w/ Headlight Cover)

HINT:

Use the same procedure described for the LH side.


Hide 53292A 13.INSTALL UPPER RADIATOR SUPPORT SEAL

a.

Install the upper radiator support seal with the 7 clips.


Hide 53806 14.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

a.

Push in the clip to install the front fender splash shield sub-assembly LH.


b.

Install the 3 bolts and screw.


Hide 53805 15.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

a.

Push in the clip to install the front fender splash shield sub-assembly RH.


b.

Install the 3 bolts and 2 screws.


Hide 17.ADJUST FOG LIGHT AIMING (w/ Fog Light)

Hide 18.ADD WASHER FLUID (w/ Headlight Cleaner System)

a.

Add washer fluid to the washer jar.


Hide 19.INSPECT TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ TOYOTA Parking Assist-sensor System)

Hide 86790B 20.ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Multi-terrain Monitor)