Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255254 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA3  Vehicle Speed Sensor Circuit  


DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU (master cylinder solenoid). If the skid control ECU (master cylinder solenoid) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No. DTC Detection Condition Trouble Area
C1AA3 While driving with the road sign assist system activated, a signal indicating a malfunction in the vehicle speed sensor is received from the skid control ECU for 5 seconds or more.
·

Vehicle stability control system

·

Skid control ECU (master cylinder solenoid)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.



Result:
Result Proceed to
Vehicle stability control system DTCs are not output. A
Vehicle stability control system DTCs are output. B



A

2.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)

B

2.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AA3 is output A
DTC C1AA3 is not output B



A

3.REPLACE FORWARD RECOGNITION CAMERA

B

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).


b.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



NEXT

4.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
4.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AA3 is output A
DTC C1AA3 is not output B



A

B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)