The skid control ECU (master cylinder solenoid) receives vehicle stability signals from the yaw rate and acceleration sensor (airbag sensor assembly). If the skid control ECU (master cylinder solenoid) detects a yaw rate sensor zero point malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA6 is stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA6 | While driving with the road sign assist system activated, a yaw rate sensor zero point malfunction signal sent from the skid control ECU (master cylinder solenoid) to the forward recognition camera is detected for 5 seconds or more. | ·
Vehicle stability control system ·
Skid control ECU (master cylinder solenoid) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output. | A |
| Vehicle stability control system DTCs are output. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA6 is output. | A |
| DTC C1AA6 is not output. | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).
Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA6 is output. | A |
| DTC C1AA6 is not output. | B |
A
B