Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255254 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AA8  Front Camera Module Incorrect Axial Gap  C1AA9  Front Camera Module Beam Axis Not Adjusted  


DESCRIPTION

If the forward recognition camera determines that the forward recognition camera axis has deviated, DTC C1AA8 is stored. Also, if the camera sensor optical axis learning is not performed after installing the forward recognition camera, DTC C1AA9 is stored.

DTC No. DTC Detection Condition Trouble Area
C1AA8 While the engine switch is on (IG) and the road sign assist system is operating, the forward recognition camera detects forward recognition camera optical axis deviation.
·

Forward recognition camera

·

Windshield glass


C1AA9 While the engine switch is on (IG), the forward recognition camera detects that forward recognition camera adjustment has not been completed.

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



PROCEDURE

1.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.



Result Proceed to
Current DTC C1AA8 is output A
Current DTC C1AA9 is output B
History DTC C1AA8 is output C


A

2.CHECK VEHICLE CONDITION

B

6.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

C

9.CLEAR DTC
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or being towed. A
Vehicle is overloaded or being towed. B



A

3.CHECK WHEEL ALIGNMENT

B

10.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
3.CHECK WHEEL ALIGNMENT
a.

Check the front wheel alignment (toe) (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).

HINT:

DTC C1AA8 may be stored if the forward recognition camera optical axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front wheel is misaligned (toe) A
Front wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

5.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).



NEXT

PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

5.CHECK FORWARD RECOGNITION CAMERA INSTALLATION
a.

Check the installation condition of the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION).

HINT:

If there is a malfunction with the installation condition of the forward recognition camera, replace the windshield glass.



Result:
Result Proceed to
No deformation or deviation in forward recognition camera installation bracket A
Deformation or deviation in forward recognition camera installation bracket B



A

6.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

B

8.REPLACE WINDSHIELD GLASS
6.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
a.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



NEXT

7.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
7.CHECK DTC OUTPUT (ROAD SIGN ASSIST SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Road Sign Assist / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC C1AA8 or C1AA9 is output. A
DTC C1AA8 and C1AA9 are not output. B



A

REPLACE FORWARD RECOGNITION CAMERA

B

END

8.REPLACE WINDSHIELD GLASS
a.

Replace the windshield glass (See page Vehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL).



NEXT

PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING

9.CLEAR DTC
a.

Check for DTCs related to forward recognition camera.

HINT:

If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when optical axis learning was performed.





NEXT

END

10.PERFORM FORWARD RECOGNITION CAMERA OPTICAL AXIS LEARNING
a.

Return the vehicle to normal operating conditions.


b.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).




NEXT

END