Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2015.08
RM2660E _59 Vehicle Exterior _052850 WINDOW / GLASS _0255724 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the road sign assist system, lane departure alert system, forward recognition camera system, dynamic radar cruise control system, pre-crash safety system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 28800 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53883F 4.REMOVE FRONT FENDER MAIN SEAL LH

Hide 53882H 5.REMOVE FRONT FENDER MAIN SEAL RH

Hide 6.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 7.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55781E 8.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 75534 9.REMOVE WINDSHIELD OUTSIDE MOULDING LH

a.
B180565E04
2.021,1.531 2.323,1.792 2.323,1.792 2.323,1.479 false 2.292,1.823 2.479,2.021 0.188,0.198 10 true A

Remove the windshield outside moulding.

i.

Put protective tape around the moulding.


ii.

Using a moulding remover, detach the 6 clips and remove the moulding.

NOTICE:
·

When removing the windshield outside moulding, be careful not to damage the roof drip side finish moulding clip labeled A in the illustration.

·

If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.





Hide 75533 10.REMOVE WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 75548C 11.REMOVE NO. 4 WINDSHIELD MOULDING PAD

a.
B180566

Remove the 4 No. 4 windshield moulding pads.

HINT:

Use the same procedure to remove the 4 pads on the other side.



Hide 75547B 12.REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:

Perform the following procedures if replacing any No. 3 windshield outside moulding clip(s).


a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.
B180567E03
2.903,0.28 3.099,0.457 0.196,0.177 10 a

Lightly press the drill against the No. 3 windshield outside moulding clip(s), drill off the flanges of the No. 3 windshield outside moulding clip(s), and remove the No. 3 windshield outside moulding clip(s).

Standard:
Area Specified Condition
a 5.0 mm (0.197 in.)


NOTICE:
·

Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.

·

Do not pry the No. 3 windshield outside moulding clips with the drill, because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.



NOTICE:

Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.



d.

Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

HINT:

Use the same procedure to remove the clip(s) on the other side.



Hide 75561A 13.REMOVE ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:

Perform the following procedures if replacing any roof drip side finish moulding clip.


a.

Remove the roof drip side finish moulding clips.

HINT:

Use the same procedure to remove the clip on the other side.



Hide 74330C 22.REMOVE CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

Hide 74330B 23.REMOVE CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

Hide 86466E 24.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466D 25.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86464A 26.REMOVE FORWARD RECOGNITION LATCH (w/ Pre-crash Safety System)

Hide 8646C 27.REMOVE FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)

Hide 86401 28.REMOVE FORWARD RECOGNITION W/HEATER HOOD SUB-ASSEMBLY (w/ Pre-crash Safety System, Camera Heater)

Hide 87810 29.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 89941 30.REMOVE RAIN SENSOR (w/ Rain Sensor)

Hide 63310 31.REMOVE ROOF HEADLINING

a.

w/ Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/ Sliding Roof)>REMOVAL).




b.

w/o Sliding Roof:

i.

Partially remove the roof headlining.

HINT:

It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING (w/o Sliding Roof)>REMOVAL).




Hide 75533G 32.REMOVE WINDSHIELD OUTSIDE MOULDING

a.
B180616E06
1.605,0.143 1.944,0.306 0.338,0.163 10 *a

Using a knife, cut off the moulding as shown in the illustration.

Text in Illustration
*a Cut

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by hand to remove the windshield outside moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



Hide 56111 33.REMOVE WINDSHIELD GLASS

HINT:

Be careful not to damage the wire harnesses near the windshield glass with the piano wire.


a.
E271513E01
0.71,1.78 0.826,1.925 0.116,0.145 10 A

w/o Heated Windshield Defroster:

i.

Disconnect the connector A.

HINT:

w/o Heated Windshield Defroster:

The vehicle only has connector A.




b.

w/ Heated Windshield Defroster:

i.

Disconnect the 3 connectors.



c.
B183897E05
1.25,0.302 1.552,0.302 1.552,0.302 1.552,0.979 false 2.177,1.729 2.177,2.104 false 1.104,2.75 1.323,3.156 1.323,3.156 1.604,3.156 false 2.344,2.74 2.146,3.146 2.146,3.146 1.875,3.146 false 1.698,3.573 1.698,4.083 false 1.042,0.219 1.26,0.406 0.219,0.188 10 false *1 2.094,2.115 2.313,2.26 0.219,0.146 10 false *2 1.656,3.094 1.844,3.281 0.188,0.188 10 false *3 1.615,4.094 1.833,4.26 0.219,0.167 10 false *4

Apply protective tape to the outer surface of the vehicle body to prevent scratches.

Text in Illustration
*1 Plastic Sheet
*2 Protective Tape
*3 Stopper
*4 Piano Wire


d.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




f.
B436427E01
1.741,1.457 1.926,1.582 false 1.948,1.589 2.203,1.878 0.255,0.289 10 *a

Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.

Text in Illustration
*a Matchmarks

NOTICE:

Matchmarks do not need to be placed if not reusing the glass.



g.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the glass.



h.

Disconnect the stoppers.


i.

Using suction cups, remove the glass.


Hide 56116C 34.REMOVE NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a scraper, remove the 2 stoppers.


Hide 56117D 35.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

Using a scraper, remove the dam.


Hide 56165 36.REMOVE FRONT INNER WINDOW MOULDING COVER LH

a.

Using a scraper, remove the cover.


Hide 56111 37.CLEAN WINDSHIELD GLASS

a.
B106929

Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.


b.

Clean the outer circumference of the glass with non-residue solvent.

NOTICE:
·

Do not touch the glass surface after cleaning it.

·

Be careful not to damage the glass.

·

Even if using new glass, clean the glass with non-residue solvent.




Hide 56115C 38.REMOVE WINDSHIELD GLASS STOPPER

a.

Remove the 2 windshield glass stoppers.


Hide 39.CLEAN VEHICLE BODY

a.
B106081E24
0.49,1.323 0.771,0.75 0.771,0.75 0.948,0.75 false 2.271,1.438 2.552,0.74 2.552,0.74 2.719,0.74 false 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.969,0.667 1.208,0.865 0.24,0.198 10 false *1 2.75,0.646 2.99,0.844 0.24,0.198 10 false *1 0.719,1.781 0.958,1.979 0.24,0.198 10 false *2 2.323,1.781 2.563,1.979 0.24,0.198 10 false *2

Clean and shape the contact surface of the vehicle body.

Text in Illustration
*1 Adhesive

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.