The forward recognition camera receives vehicle speed signals from the skid control ECU (master cylinder solenoid). If the skid control ECU (master cylinder solenoid) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA3 | 2 seconds after the engine switch is turned on (IG), a signal from the skid control ECU (master cylinder solenoid) indicating a malfunction in a vehicle speed sensor is detected by the forward recognition camera for 5 seconds or more. | ·
Vehicle stability control system ·
Skid control ECU (master cylinder solenoid) ·
Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If DTC C1AA3 is stored, the vehicle stability control system may be malfunctioning. Check for DTCs related to the vehicle stability control system first.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output. | A |
| Vehicle stability control system DTCs are output. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG) and wait 7 seconds or more.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA3 is output | A |
| DTC C1AA3 is not output | B |
A
B
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).
Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / LKA/LDA / Trouble Codes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG) and wait 7 seconds or more.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA3 is output (for LHD) | A |
| DTC C1AA3 is output (for RHD) | B |
| DTC C1AA3 is not output | C |
A
B
C