Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255256 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The forward recognition camera uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the forward recognition camera detects this, and stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A11 2 seconds after the engine switch is turned on (IG), misalignment of the millimeter wave radar sensor assembly is detected for 5 seconds or more.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera


C1A14 2 seconds after the engine switch is turned on (IG), incompletion of the millimeter wave radar sensor assembly beam axis alignment is detected for 5 seconds or more.
·

Millimeter wave radar sensor assembly

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Check if the stored DTCs are current DTCs.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



Result
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C


A

2.CHECK VEHICLE CONDITION

B

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

C

15.CLEAR DTC
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result
Result Proceed to
Vehicle is not overloaded or being towed A
Vehicle is overloaded or being towed B


A

3.CHECK WHEEL ALIGNMENT

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CHECK WHEEL ALIGNMENT
a.

Check the front wheel alignment (toe) (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result
Result Proceed to
Front wheel is misaligned (toe) A
Front wheels are not misaligned (toe) B


A

4.ADJUST WHEEL ALIGNMENT

B

7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

6.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
6.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B


A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

16.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).

Result
Result Proceed to
Bracket is not deformed A
No. 1 millimeter wave radar sensor bracket is deformed B
The other bracket than No. 1 millimeter wave radar sensor bracket is deformed C



A

8.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

10.REPLACE NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET

C

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

8.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

9.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
9.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




g.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET WAS DEFECTIVE)

B

16.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
10.REPLACE NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET
a.

Replace the No. 1 millimeter wave radar sensor bracket with a new one (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DISASSEMBLY).


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

11.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
11.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




g.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).




NEXT

END

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

14.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
14.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B


A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

18.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
15.CLEAR DTC
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.

HINT:

If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.





NEXT

END

16.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

17.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
17.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.




g.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA

18.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

19.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
19.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B


A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE FORWARD RECOGNITION CAMERA