Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255256 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AA3  Vehicle Speed Sensor Circuit  


DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU (master cylinder solenoid). If the skid control ECU (master cylinder solenoid) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No. DTC Detection Condition Trouble Area
C1AA3 2 seconds after the engine switch is turned on (IG), a signal from the skid control ECU (master cylinder solenoid) indicating a malfunction in a vehicle speed sensor is detected by the forward recognition camera for 5 seconds or more.
·

Vehicle stability control system

·

Skid control ECU (master cylinder solenoid)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)
HINT:

If DTC C1AA3 is stored, the VSC system may be malfunctioning. Check for DTCs related to the VSC system first.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.



Result:
Result Proceed to
Vehicle stability control system DTCs are not output. A
Vehicle stability control system DTCs are output. B



A

2.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)

B

2.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC C1AA3 is output A
DTC C1AA3 is not output B



A

3.REPLACE FORWARD RECOGNITION CAMERA

B

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).


b.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



NEXT

4.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
4.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn the engine switch on (IG) and wait 7 seconds or more.





Result:
Result Proceed to
DTC C1AA3 is output (for LHD) A
DTC C1AA3 is output (for RHD) B
DTC C1AA3 is not output C



A

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

B

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU)

C

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)