Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255263 AUTOMATIC TRANSMISSION UNIT A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C163084E01
1.175,0.672 1.304,0.836 0.128,0.165 10 A 4.469,1.526 4.597,1.691 0.128,0.165 10 C 1.6,2.223 1.729,2.388 0.128,0.165 10 B 6.038,1.019 6.166,1.184 0.128,0.165 10 E 0.799,5.482 0.928,5.647 0.128,0.165 10 F 1.9,5.164 2.029,5.329 0.128,0.165 10 G 2.096,6.557 2.224,6.722 0.128,0.165 10 H 3.371,7.581 3.500,7.746 0.128,0.165 10 I 5.357,5.743 5.485,5.908 0.128,0.165 10 J 5.612,2.733 5.741,2.898 0.128,0.165 10 D

Bearing and Race Diameter:
Mark Front Race Diameter Inside / Outside Thrust Bearing Diameter Inside / Outside Rear Race Diameter Inside / Outside
A 74.26 to 74.56 mm (2.92 to 2.94 in.) / 87.39 to 87.74 mm (3.44 to 3.45 in.) 71.96 to 72.26 mm (2.83 to 2.84 in.) / 85.25 to 85.6 mm (3.36 to 3.37 in.) -
B 38.0 to 38.3 mm (1.50 to 1.51 in.) / 53.9 to 54.1 mm (2.12 to 2.13 in.) 36.45 to 36.7 mm (1.44 to 1.45 in.) / 52.96 to 53.26 mm (2.09 to 2.10 in.) -
C - 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.63 to 39.88 mm (1.56 to 1.57 in.) 22.8 to 23.1 mm (0.898 to 0.909 in.) / 44.5 to 44.75 mm (1.75 to 1.76 in.)
D - 39.45 to 39.7 mm (1.55 to 1.56 in.) / 60.5 to 60.75 mm (2.38 to 2.39 in.) -
E - 46.45 to 46.7 mm (1.83 to 1.84 in.) / 64.3 to 64.55 mm (2.53 to 2.54 in.) -
F 55.0 to 55.2 mm (2.165 to 2.173 in.) / 68.8 to 69.3 mm (2.71 to 2.73 in.) 54.55 to 54.8 mm (2.15 to 2.16 in.) / 70.0 to 70.5 mm (2.76 to 2.78 in.) -
G - 65.35 to 65.6 mm (2.57 to 2.58 in.) / 85.6 to 85.95 mm (3.37 to 3.38 in.) 62.85 to 63.1 mm (2.47 to 2.48 in.) / 82.3 to 82.6 mm (3.24 to 3.25 in.)
H 39.67 to 39.87 mm (1.56 to 1.57 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.) 36.45 to 36.61 mm (1.437 to 1.441 in.) / 56.62 to 56.92 mm (2.23 to 2.24 in.) 36.45 to 36.7 mm (1.435 to 1.445 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.)
I 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.5 to 39.8 mm (1.56 to 1.57 in.) 23.2 to 23.4 mm (0.913 to 0.921 in.) / 43.9 to 44.15 mm (1.73 to 1.74 in.) -
J - 43.6 to 43.85 mm (1.72 to 1.73 in.) / 62.3 to 62.8 mm (2.45 to 2.47 in.) 47.15 to 47.4 mm (1.86 to 1.87 in.) / 66.9 to 67.1 mm (2.63 to 2.64 in.)


Hide 35623H 2.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C161741E02
2.168,0.749 2.896,0.448 false 2.933,1.217 2.896,0.448 false 2.628,0.916 2.896,0.448 false 2.896,0.448 2.996,0.146 2.996,0.146 2.821,0.146 false 2.58,0.063 2.732,0.214 0.152,0.151 10 *1

Coat 3 new O-rings with ATF and install them to the 1st and reverse brake piston.

Text in Illustration
*1 New O-Ring


b.
U164579E02
2.99,2.927 2.563,2.927 2.563,2.927 2.021,3.604 false 1.292,0.094 1.385,0.094 1.385,0.094 1.698,0.406 false 1.042,0.031 1.292,0.208 0.25,0.177 10 false *1 3.031,2.802 3.292,3.021 0.26,0.219 10 false *2

Install the 1st and reverse brake piston to the transmission case.

NOTICE:
·

Be careful not to damage the O-ring.

·

Make sure that the parking hole of the brake piston is on the bottom by engaging the brake piston protrusion and the transmission case spline grooves.



Text in Illustration
*1 Protrusion
*2 Parking Hole


Hide 35068 3.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Place the 1st and reverse brake return spring onto the 1st and reverse brake piston.


b.

Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 35689A 4.SELECT NO. 4 BRAKE FLANGE

a.
C228889E01
1.08,1 1.212,1.150 0.132,0.150 10 A 1.57,1.194 1.726,1.346 0.156,0.151 10 *1 1.762,1.278 1.828,1.278 1.828,1.278 1.942,0.84 false

Measure distance A (from the tip of the 1st and reverse brake piston to the step in the transmission case) in the illustration.*1

Text in Illustration
*1 Brake Piston

HINT:

Standard distance A: 27.82 to 28.42 mm (1.09 to 1.12 in.)



b.
C162578E02
1.471,0.95 1.594,1.114 0.123,0.163 10 B 1.281,1.121 1.423,1.295 0.142,0.174 10 H 0.477,1.641 0.648,1.790 0.171,0.149 10 *a 0.387,1.225 0.547,1.601 false 2.816,0.423 3.171,0.625 0.355,0.202 10 *2 2.816,0.1 3.180,0.302 0.364,0.202 10 *1 2.643,0.505 2.788,0.505 false 2.333,0.397 2.778,0.241 false 2.816,1.247 3.299,1.454 0.483,0.207 10 *3 2.643,1.467 2.788,1.39 false

Assemble the flange, No. 4 brake flange, 7 No. 4 brake discs and 6 plates, and measure distance B in the illustration.*2

Text in Illustration
*1 Disc
*2 Plate
*3 Flange
*a Selected No. 4 brake flange

HINT:

Standard distance B: 25.98 to 27.01 mm (1.02 to 1.06 in.)



c.

Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 4 brake flange indicated by the graph point.


d.

Measure length H of the selected No. 4 brake flange as shown in the illustration.

HINT:

Make sure that when the B measurement and the H dimension of the selected No. 4 brake flange are subtracted from the A measurement, the value is 0.961 to 1.261 mm (0.0378 to 0.0495 in.).


U164583E01
1.971,0.616 2.706,0.838 0.736,0.223 10 27.6 (1.09) 3.26,0.616 3.989,0.838 0.729,0.223 10 28.0 (1.10) 4.734,0.616 5.483,0.838 0.749,0.223 10 28.4 (1.12) 1.267,1.047 2.022,1.253 0.756,0.206 10 25.8 (1.15) 1.267,2.38 2.028,2.599 0.761,0.219 10 26.2 (1.03) 1.267,3.734 2.036,3.945 0.769,0.210 10 26.6 (1.05) 1.267,5.039 1.998,5.250 0.731,0.211 10 27.0 (1.06) 3.841,0.06 4.087,0.271 0.246,0.211 10 *a 0.149,3.093 0.395,3.283 0.246,0.191 10 *b 4.394,6.042 4.581,6.201 0.187,0.159 10 *1 4.969,6.042 5.156,6.201 0.187,0.159 10 *2 5.911,5.589 6.098,5.748 0.187,0.159 10 *3 5.911,4.923 6.098,5.082 0.187,0.159 10 *4 5.911,4.274 6.098,4.434 0.187,0.159 10 *5 5.911,3.469 6.098,3.628 0.187,0.159 10 *6

Text in Illustration
*1 Mark 0 *2 Mark 2
*3 Mark 4 *4 Mark 6
*5 Mark 8 *6 Mark 10
*a Distance A mm (in.) *b Distance B mm (in.)

Selected No. 4 Brake Flange Length H:
Mark Length H
0 0 mm (0 in.)
2 0.15 to 0.25 mm (0.00590 to 0.00984 in.)
4 0.35 to 0.45 mm (0.0138 to 0.0177 in.)
6 0.55 to 0.65 mm (0.0217 to 0.0256 in.)
8 0.75 to 0.85 mm (0.0295 to 0.0335 in.)
10 0.95 to 1.05 mm (0.0374 to 0.0413 in.)



Hide 35760 5.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
C161739E04
1.938,1.25 2.385,1.25 false 2.427,1.167 2.698,1.396 0.271,0.229 10 true *1

Install the thrust bearing race.

Text in Illustration
*1 Race J

HINT:

Use a small amount of MP grease to make the thrust bearing race stay securely in place.


Bearing Race Diameter:
Item Inside Outside
Race J 47.15 to 47.4 mm (1.86 to 1.87 in.) 66.9 to 67.1 mm (2.63 to 2.64 in.)



b.
C162772E04
2.844,0.604 2.719,0.208 2.719,0.208 2.604,0.208 false 0.604,1.521 0.698,1.844 0.698,1.844 0.823,1.844 false 2.385,0.094 2.625,0.302 0.24,0.208 10 false *2 0.865,1.74 1.083,1.938 0.219,0.198 10 false *1

Install the 2 thrust needle roller bearings to the rear planetary gear assembly.

Bearing Diameter:
Item Inside Outside
Bearing I 23.2 to 23.4 mm (0.913 to 0.921 in.) 43.9 to 44.15 mm (1.73 to 1.74 in.)
Bearing J 43.6 to 43.85 mm (1.72 to 1.73 in.) 62.3 to 62.8 mm (2.45 to 2.47 in.)


Text in Illustration
*1 Bearing I
*2 Bearing J

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.



c.

Install the rear planetary gear assembly.


Hide 35639B 6.INSTALL BRAKE PLATE STOPPER SPRING

Hide 35761 7.INSTALL REAR PLANETARY RING GEAR

a.

Install the rear planetary ring gear flange to the rear planetary ring gear.


b.

Using a screwdriver, install the snap ring.


c.
C161733E03
1.639,0.955 1.222,0.361 1.222,0.361 1.096,0.361 false 1.524,1.216 1.714,1.487 1.714,1.487 1.84,1.487 false 1.29,1.286 1.695,1.864 1.695,1.864 1.821,1.864 false 3.098,0.582 2.816,0.18 2.816,0.18 2.638,0.18 false 1.888,1.783 2.068,1.942 0.180,0.159 10 *1 1.888,1.411 2.068,1.570 0.180,0.159 10 *2 0.839,0.277 1.019,0.436 0.180,0.159 10 *3 2.369,0.099 2.549,0.258 0.180,0.159 10 *4

Install the 3 thrust bearing races, thrust needle roller bearing and rear planetary ring gear together with the rear planetary ring gear flange to the intermediate shaft.

Text in Illustration
*1 Front Race H
*2 Bearing H
*3 Rear Race H
*4 Race I

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings and races stay securely in place.


Bearing and Race Diameter:
Item Inside Outside
Front race H 39.67 to 39.87 mm (1.56 to 1.57 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)
Bearing H 36.45 to 36.61 mm (1.437 to 1.441 in.) 56.62 to 56.92 mm (2.23 to 2.24 in.)
Rear race H 36.45 to 36.7 mm (1.435 to 1.445 in.) 56.5 to 57.0 mm (2.22 to 2.24 in.)
Race I 21.05 to 21.3 mm (0.829 to 0.839 in.) 39.5 to 39.8 mm (1.56 to 1.57 in.)



Hide 35713 8.INSTALL INTERMEDIATE SHAFT WITH REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

C163074

a.

Install the intermediate shaft together with the rear planetary ring gear flange and rear planetary ring gear to the transmission case.


Hide 35684 9.INSTALL NO. 4 BRAKE DISC

C358647E01
1.146,0.573 1.354,0.573 false 1.146,0.99 1.354,0.99 false 1.146,1.344 1.354,1.344 false 1.125,1.76 1.333,1.76 false 1.125,2.115 1.333,2.115 false 1.125,2.5 1.333,2.5 false 1.146,2.896 1.354,2.896 false 2.115,0.771 2.323,0.771 false 2.125,1.177 2.333,1.177 false 2.135,1.531 2.375,1.531 false 2.125,1.938 2.365,1.938 false 2.125,2.333 2.365,2.333 false 2.146,2.708 2.385,2.708 false 2.125,3.083 2.365,3.083 false 1.146,3.354 1.354,3.354 false 0.854,0.49 1.198,0.688 0.344,0.198 10 false S/F 0.969,0.885 1.135,1.073 0.167,0.188 10 false P 0.969,1.26 1.135,1.448 0.167,0.188 10 false P 0.979,1.677 1.146,1.865 0.167,0.188 10 false P 0.969,2.031 1.135,2.219 0.167,0.188 10 false P 0.979,2.417 1.146,2.594 0.167,0.177 10 false P 0.979,2.802 1.146,2.979 0.167,0.177 10 false P 0.99,3.271 1.156,3.448 0.167,0.177 10 true F 2.365,0.698 2.531,0.885 0.167,0.188 10 false D 2.385,1.063 2.552,1.25 0.167,0.188 10 false D 2.417,1.427 2.583,1.615 0.167,0.188 10 false D 2.406,1.833 2.573,2.021 0.167,0.188 10 false D 2.396,2.25 2.563,2.438 0.167,0.188 10 false D 2.427,2.604 2.594,2.792 0.167,0.188 10 false D 2.385,3 2.552,3.188 0.167,0.188 10 true D

a.

Install the flange, 7 discs, 6 plates and selected No. 4 brake flange.

Install in order:

F - D - P - D - P - D - P - D - P - D - P - D - P - D - S/F


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected No. 4 brake flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35797B 10.INSTALL 1-WAY CLUTCH INNER RACE

U164580E01
2.594,1.354 2.758,1.519 0.164,0.165 10 *a

Text in Illustration
*a Front

a.

Install the No. 3 1-way clutch inner race to the No. 3 1-way clutch assembly.

NOTICE:

Be sure to install the 1-way clutch inner race so that it is facing in the proper direction.



Hide 35770C 12.INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

C163075

a.

Install the No. 3 1-way clutch assembly to the transmission case.


b.

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35622G 13.INSTALL NO. 2 BRAKE PISTON

a.
C162730E03
1.011,0.034 1.176,0.187 0.165,0.153 10 *1 0.604,1.248 0.829,0.135 0.829,0.135 0.976,0.135 false 1.038,0.566 0.829,0.135 false

Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

Text in Illustration
*1 New O-ring


b.

Press the No. 2 brake piston into the No. 2 brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



Hide 35699 14.INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

a.

Install the No. 2 brake cylinder with No. 2 brake piston to the transmission case.

NOTICE:
·
C161729


·

When installing the No. 2 brake cylinder with No. 2 brake piston to the transmission case, align the cylinder claw with the groove in the top of the case.

·

Make sure the No. 2 brake cylinder with No. 2 brake piston is securely inserted into the transmission case.




Hide 35678B 15.SELECT NO. 2 BRAKE FLANGE

a.

Install the No. 2 brake piston return spring and flange to the No. 2 brake piston.


b.

Place SST on the No. 2 brake flange and compress the No. 2 brake piston return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)


c.

Using a screwdriver, install the snap ring to the transmission case.


d.
C162575E04
1.792,1.604 1.094,2.104 1.094,2.104 0.917,2.104 false 1.188,0.917 1.344,1.104 0.156,0.188 10 false A 0.719,2.01 0.906,2.25 0.188,0.24 10 false *1

Measure distance A (from the top surface of the snap ring to the top surface of the No. 2 brake piston return spring) in the illustration.*1

Text in Illustration
*1 No. 2 Brake Piston Return Spring

HINT:

Standard distance A: 21.00 to 21.76 mm (0.834 to 0.857 in.)



e.
C162576E05
2.094,1.052 2.5,1.083 false 1.427,0.635 0.667,0.583 false 2.073,1.135 2.51,1.271 false 2.781,0.75 2.604,0.781 false 0.719,0.958 0.865,1.135 0.146,0.177 10 false B 2.083,0.24 2.281,0.417 0.198,0.177 10 false *b 2.542,1.167 2.896,1.354 0.354,0.188 10 false *3 2.552,1.01 2.938,1.177 0.385,0.167 10 false *2 0.448,0.49 0.646,0.656 0.198,0.167 10 false *a 2.792,0.646 3.26,0.865 0.469,0.219 10 false *1

Assemble the 4 discs, 3 plates and flange as shown in the illustration. Then, with a fixture of 165.2 mm (6.50 in.) or less placed on the flange, measure distance B.*2

Text in Illustration
*1 Flange
*2 Plate
*3 Disc
*a Fixture
*b 165.2 mm or less

HINT:

Standard distance B: 16.54 to 17.15 mm (0.651 to 0.675 in.)



f.

Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 2 brake flange indicated by the graph point.

U164582E01
3.872,0.133 4.053,0.288 0.181,0.154 10 *a 0.211,3.174 0.396,3.321 0.185,0.147 10 *b 2.256,0.543 3.121,0.768 0.864,0.225 10 21.0 (0.827) 3.68,0.543 4.546,0.773 0.866,0.230 10 21.4 (0.843) 5.123,0.543 5.955,0.798 0.832,0.255 10 21.8 (0.858) 0.857,0.891 1.695,1.131 0.838,0.240 10 16.5 (0.650) 0.857,2.338 1.707,2.557 0.850,0.218 10 16.7 (0.657) 0.857,3.753 1.707,3.972 0.850,0.218 10 16.9 (0.665) 0.857,5.213 1.703,5.421 0.847,0.208 10 17.1 (0.673) 4.291,6.182 4.475,6.353 0.184,0.171 10 *1 4.887,6.441 5.071,6.612 0.184,0.171 10 *2 5.241,6.182 5.425,6.353 0.184,0.171 10 *3 5.613,6.441 5.797,6.612 0.184,0.171 10 *4 6.074,6.182 6.258,6.353 0.184,0.171 10 *5 6.535,5.549 6.719,5.720 0.184,0.171 10 *6 6.535,4.853 6.719,5.024 0.184,0.171 10 *7 6.535,3.788 6.719,3.960 0.184,0.171 10 *8

Text in Illustration
*1 Mark 0 *2 Mark 1
*3 Mark 2 *4 Mark 3
*5 Mark 4 *6 Mark 5
*7 Mark 6 *8 Mark 7
*a Distance A mm (in.) *b Distance B mm (in.)

HINT:

Make sure that when the B measurement and selected No. 2 brake flange thickness are subtracted from the A measurement, the value is 2.20 to 2.50 mm (0.0866 to 0.0984 in.).


Flange Thickness:
Mark Thickness
0 1.95 to 2.05 mm (0.0768 to 0.0807 in.)
1 2.05 to 2.15 mm (0.0807 to 0.0846 in.)
2 2.15 to 2.25 mm (0.0846 to 0.0886 in.)
3 2.25 to 2.35 mm (0.0886 to 0.0925 in.)
4 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
5 2.45 to 2.55 mm (0.0965 to 0.100 in.)
6 2.55 to 2.65 mm (0.100 to 0.104 in.)
7 2.65 to 2.75 mm (0.104 to 0.108 in.)



g.

Remove the snap ring, flange and No. 2 brake piston return spring from the transmission case.


Hide 35682A 16.INSTALL NO. 2 BRAKE DISC SET

C161726E11
0.604,0.292 0.542,0.292 false 0.667,0.563 0.542,0.563 false 0.667,0.823 0.542,0.823 false 0.667,1.073 0.542,1.073 false 0.667,1.313 0.542,1.313 false 1.354,0.698 1.292,0.698 false 1.354,0.938 1.292,0.938 false 1.354,1.188 1.292,1.188 false 1.354,1.406 1.292,1.406 false 1.365,1.323 1.625,1.5 0.26,0.177 10 true S/F 0.406,0.198 0.531,0.365 0.125,0.167 10 false F 0.406,0.469 0.531,0.635 0.125,0.167 10 false D 0.406,0.75 0.531,0.917 0.125,0.167 10 false D 0.406,0.979 0.531,1.146 0.125,0.167 10 false D 0.406,1.229 0.531,1.396 0.125,0.167 10 false D 1.365,0.615 1.49,0.781 0.125,0.167 10 false P 1.365,0.865 1.49,1.031 0.125,0.167 10 false P 1.354,1.104 1.469,1.271 0.115,0.167 10 true P

a.

Install the No. 2 brake piston return spring, selected No. 2 brake flange, 4 No. 2 brake discs, 3 plates and flange.

Install in order:

S/F - D - P - D - P - D - P - D - F


HINT:

S/F = Selected flange

D = No. 2 brake disc

P = Plate

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.

Place SST on the flange and compress the No. 2 brake piston return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)


c.

Using a screwdriver, install the snap ring to the transmission case.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 35750 17.INSTALL CENTER PLANETARY GEAR ASSEMBLY

a.
U164818E01
3.11,0.821 2.664,1.536 2.664,1.536 2.765,1.536 false 2.79,1.457 2.943,1.612 0.152,0.156 10 *1

Install the center planetary sun gear and center planetary gear assembly to the transmission case.

Text in Illustration
*1 Return Spring Retainer

NOTICE:

Make sure to install the center planetary sun gear with the groove facing the transmission case.



Hide 35621V 18.INSTALL NO. 1 BRAKE PISTON

a.
C162732E03
1.125,0.03 1.342,0.206 0.217,0.175 10 *1 0.616,1.239 0.946,0.133 0.946,0.133 1.094,0.133 false 1.2,0.683 0.946,0.133 false

Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

Text in Illustration
*1 New O-Ring


b.

Press the No. 1 brake piston into the No. 1 brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



Hide 35698 19.INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

a.

Install the No. 1 brake cylinder with No. 1 brake piston and brake piston return spring to the transmission case.

NOTICE:
·
U152353E01
1.725,0.206 1.753,0.225 false 1.785,0.271 1.795,0.278 false 1.699,0.214 1.759,0.254 false 1.705,0.244 1.788,0.299 false 1.711,0.273 1.781,0.32 false 1.697,0.289 1.774,0.341 false 1.686,0.308 1.767,0.362 false 1.74,0.369 1.76,0.383 false


·

When installing the No. 1 brake cylinder with No. 1 brake piston to the transmission case, align the cylinder claw with the groove in the top of the case

·

Make sure the No. 1 brake cylinder with No. 1 brake piston is securely inserted into the transmission case.




b.

Place SST on the brake piston return spring and compress the brake piston return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


c.

Using a screwdriver, install the snap ring to the transmission case.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 35676B 20.SELECT NO. 1 BRAKE FLANGE

C162573E02
1.377,1.035 1.526,1.223 0.149,0.188 10 A 0.51,1.545 0.705,1.710 0.195,0.165 10 *1 0.756,1.633 0.862,1.633 0.862,1.633 1.834,1.925 false

a.

Measure distance A (from the step in the transmission case to the tip of the No. 1 brake piston) in the illustration.*1

HINT:

Standard distance A: 19.74 to 20.22 mm (0.777 to 0.796 in.)



b.
C162574E04
2.292,0.698 2.656,0.698 false 1.917,0.615 2.656,0.448 false 0.781,0.844 0.927,1.052 0.146,0.208 10 false B 2.698,0.333 2.865,0.5 0.167,0.167 10 false *1 2.719,0.604 2.927,0.781 0.208,0.177 10 false *2

Assemble the 4 plates and 4 discs and measure distance B in the illustration.*2

HINT:

Standard distance B: 16.72 to 17.19 mm (0.658 to 0.677 in.)


Text in Illustration
*1 Disc
*2 Plate


c.

Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 1 brake flange indicated by the graph point.

U164581E01
3.421,0.085 3.621,0.265 0.200,0.180 10 *a 0.066,3.039 0.240,3.207 0.173,0.168 10 *b 1.06,0.69 1.903,0.907 0.843,0.216 10 19.6 (0.772) 2.286,0.69 3.129,0.907 0.843,0.216 10 19.8 (0.780) 3.505,0.69 4.348,0.907 0.843,0.216 10 20.0 (0.787) 4.759,0.69 5.602,0.907 0.843,0.216 10 20.2 (0.795) 6.034,0.69 6.877,0.907 0.843,0.216 10 20.4 (0.803) 0.388,1.04 1.180,1.251 0.792,0.211 10 16.5 (0.650) 0.388,2.287 1.180,2.499 0.792,0.211 10 16.7 (0.657) 0.388,3.525 1.180,3.736 0.792,0.211 10 16.9 (0.665) 0.388,4.765 1.180,4.976 0.792,0.211 10 17.1 (0.673) 0.388,6.003 1.180,6.215 0.792,0.211 10 17.3 (0.681) 6.619,4.494 6.792,4.655 0.173,0.161 10 *4 6.619,5.736 6.796,5.892 0.178,0.157 10 *3 5.134,6.268 5.304,6.439 0.170,0.171 10 *2 3.736,6.268 3.920,6.434 0.184,0.166 10 *1

Text in Illustration
*1 Mark 0 *2 Mark 1
*3 Mark 2 *4 Mark 3
*a Distance A mm (in.) *b Distance B mm (in.)

HINT:

Make sure that when the B measurement and selected flange thickness are subtracted from the A measurement, the value is 0.56 to 0.86 mm (0.0220 to 0.0339 in.).


Flange Thickness:
Mark Thickness
0 1.95 to 2.05 mm (0.0768 to 0.0807 in.)
1 2.15 to 2.25 mm (0.0846 to 0.0886 in.)
2 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
3 2.55 to 2.65 mm (0.100 to 0.104 in.)



Hide 35763 21.INSTALL CENTER PLANETARY RING GEAR

a.

Install the front planetary ring gear flange to the center planetary ring gear.


b.

Using a screwdriver, install the snap ring.


Hide 35743 22.INSTALL FRONT PLANETARY RING GEAR

a.

Install the front planetary ring gear to the center planetary ring gear.


Hide 35743 23.INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

a.
C161716E04
1.969,1.063 2.469,1.063 false 1.958,1.354 2.458,1.354 false 2.531,1.281 2.771,1.479 0.24,0.198 10 true *2 2.51,0.969 2.74,1.177 0.229,0.208 10 true *1

Install the thrust bearing race and thrust needle roller bearing.

Text in Illustration
*1 Bearing
*2 Race

HINT:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.


Bearing and Race Diameter:
Item Inside Outside
Race 62.85 to 63.1 mm (2.47 to 2.48 in.) 82.3 to 82.6 mm (3.24 to 3.25 in.)
Bearing 65.35 to 65.6 mm (2.57 to 2.58 in.) 85.6 to 85.95 mm (3.37 to 3.38 in.)



b.

Install the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear to the transmission case.


Hide 35720 24.INSTALL FRONT PLANETARY GEAR ASSEMBLY

C163097

a.

Install the No. 2 planetary carrier thrust washer to the front planetary gear assembly.

HINT:

Use a small amount of MP grease to make the No. 2 planetary carrier thrust washer stay securely in place.



b.
C163096E04
1.927,1.74 2.188,1.74 false 1.927,2.271 2.177,2.271 false 2.219,1.635 2.479,1.844 0.26,0.208 10 true *2 2.24,2.198 2.49,2.375 0.25,0.177 10 true *1

Install the thrust needle roller bearing, thrust bearing race, front planetary sun gear and front planetary gear assembly.

HINT:

Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.


Text in Illustration
*1 Bearing
*2 Race

Bearing Diameter:
Item Inside Outside
Bearing 54.55 to 54.8 mm (2.15 to 2.16 in.) 70.0 to 70.5 mm (2.76 to 2.78 in.)
Race 55.0 to 55.2 mm (2.165 to 2.173 in.) 68.8 to 69.3 mm (2.71 to 2.73 in.)



Hide 35707C 25.INSTALL 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

a.

Install the No. 1 planetary carrier thrust washer to the 1-way clutch inner race, and then install them to the 1-way clutch assembly.

HINT:

Use a small amount of MP grease to make the No. 1 planetary carrier thrust washer stay securely in place.



Hide 35790 27.INSTALL 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

a.

Install the 1-way clutch assembly with the 1-way clutch inner race to the transmission case.


Hide 35681A 28.INSTALL NO. 1 BRAKE DISC SET

C161721E03
0.281,0.365 0.188,0.365 false 0.281,0.688 0.198,0.688 false 0.281,1 0.198,1 false 0.281,1.323 0.198,1.323 false 0.281,1.635 0.198,1.635 false 1.052,0.49 1.135,0.49 false 1.052,0.813 1.135,0.813 false 1.052,1.146 1.135,1.146 false 1.052,1.479 1.135,1.479 false 0.073,0.271 0.198,0.438 0.125,0.167 10 false F 1.146,0.406 1.271,0.573 0.125,0.167 10 false D 0.063,0.604 0.188,0.771 0.125,0.167 10 false P 0.063,0.917 0.188,1.083 0.125,0.167 10 false P 0.063,1.24 0.188,1.406 0.125,0.167 10 false P 0.063,1.552 0.188,1.719 0.125,0.167 10 false P 1.146,0.74 1.271,0.906 0.125,0.167 10 false D 1.146,1.063 1.271,1.229 0.125,0.167 10 true D 1.146,1.396 1.271,1.563 0.125,0.167 10 true D

a.

Install the 4 plates, 4 discs and No. 1 brake flange.

Install in order:

P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = No. 1 brake flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35624 29.INSTALL NO. 3 BRAKE PISTON

C161713E03
0.63,0.063 0.793,0.238 0.163,0.176 10 *1 1.044,0.676 0.57,0.485 false 0.758,1.057 0.457,0.145 0.457,0.145 0.595,0.145 false

Text in Illustration
*1 New O-Ring

a.

Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.


b.

Press the No. 3 brake piston into the No. 3 brake cylinder with both hands.

NOTICE:

Be careful not to damage the O-rings.



c.

Using SST and a press, compress the No. 3 brake piston return spring and install the snap ring with a screwdriver.

SST
09380-60010  (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)

NOTICE:

Be sure the end gap of the snap ring is not aligned with the No. 3 brake piston return spring claw.



Hide 35664 30.INSTALL NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.

Install the No. 3 brake cylinder together with the No. 3 brake piston and No. 3 brake piston return spring to the transmission case.

NOTICE:
·
U164589E02
1.594,0.979 1.813,0.135 1.813,0.135 1.948,0.135 false 2.052,0.917 1.813,0.135 false 1.979,0.042 2.219,0.219 0.24,0.177 10 false *1

Align the oil holes of the No. 3 brake cylinder and transmission case as shown in the illustration.

·

Make sure the No. 3 brake piston and cylinder are securely inserted into the transmission case.



Text in Illustration
*1 Oil Hole


Hide 35624J 31.INSTALL NO. 3 BRAKE PISTON HOLE SNAP RING

a.

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 35066 32.INSTALL NO. 3 BRAKE DISC SET

C161707E03
1.188,0.396 1.125,0.396 false 1.188,0.729 1.125,0.729 false 0.281,0.552 0.208,0.552 false 0.281,0.854 0.208,0.854 false 0.281,1.146 0.208,1.146 false 0.281,1.448 0.208,1.448 false 1.198,1.021 1.125,1.021 false 1.198,1.323 1.125,1.323 false 1.188,1.646 1.125,1.646 false 1.219,0.313 1.469,0.479 0.25,0.167 10 false AF 1.219,1.563 1.469,1.729 0.25,0.167 10 false OF 1.219,0.646 1.344,0.813 0.125,0.167 10 false P 1.219,0.927 1.344,1.094 0.125,0.167 10 true P 1.219,1.229 1.344,1.396 0.125,0.167 10 true P 0.073,0.469 0.198,0.635 0.125,0.167 10 false D 0.073,0.76 0.198,0.927 0.125,0.167 10 false D 0.073,1.063 0.198,1.229 0.125,0.167 10 false D 0.073,1.354 0.198,1.521 0.125,0.167 10 false D

a.

Install the ''O'' mark flange, 4 discs, 3 plates and ''A'' mark flange to the transmission case.

Install in order:

OF - D - P - D - P - D - P - D - AF


HINT:

OF = ''O'' mark flange

P = Plate

D = Disc

AF = ''A'' mark flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



Hide 35679C 33.INSTALL NO. 3 BRAKE SNAP RING

a.

Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 35606A 34.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C161812E02
1.346,0.035 1.527,0.196 0.181,0.161 10 *1 2.372,0.404 1.862,0.121 1.862,0.121 1.634,0.121 false 1.862,0.121 1.835,0.749 false

Coat 2 new O-rings with ATF and install them to the direct clutch piston.

Text in Illustration
*1 New O-ring


b.

Install the direct clutch return spring and No. 2 clutch balancer to the direct clutch piston.


c.
C162736

Press the direct clutch piston together with the direct clutch return spring and No. 2 clutch balancer into the clutch drum with both hands.

NOTICE:

Be careful not to damage the O-ring.



d.
C161704E01
0.111,0.511 0.425,0.699 0.314,0.188 10 SST 1.952,1.079 0.504,0.636 0.504,0.636 1.118,0.73 false

Place SST on the direct clutch balancer and compress the direct clutch return spring with a press.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080)

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



f.
D028536E21
1.219,1.01 1.74,1.427 1.74,1.427 2.219,1 false 1.656,1.458 1.823,1.656 0.167,0.198 10 false *1

Set the end gap of the snap ring in the balancer as shown in the illustration.

Text in Illustration
*1 Stopper

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35667A 35.INSTALL DIRECT CLUTCH DISC SET

a.

Place the oil pump assembly onto the torque converter, and then place the clutch drum onto the oil pump assembly.


b.
C177405E01
1.026,2.836 1.148,2.992 0.122,0.156 10 P 2.302,2.638 2.425,2.794 0.122,0.156 10 D 1.026,0.457 1.148,0.613 0.122,0.156 10 F 1.266,2.923 1.156,2.923 false 2.272,2.721 2.162,2.721 false 2.302,2.244 2.425,2.400 0.122,0.156 10 D 2.272,2.327 2.162,2.327 false 2.302,1.85 2.425,2.006 0.122,0.156 10 D 2.272,1.933 2.162,1.933 false 2.302,1.456 2.425,1.612 0.122,0.156 10 D 2.272,1.539 2.162,1.539 false 2.302,1.062 2.425,1.218 0.122,0.156 10 D 2.272,1.145 2.162,1.145 false 2.302,0.668 2.425,0.824 0.122,0.156 10 D 2.272,0.751 2.162,0.751 false 1.026,2.439 1.148,2.595 0.122,0.156 10 P 1.266,2.526 1.156,2.526 false 1.026,2.043 1.148,2.199 0.122,0.156 10 P 1.266,2.13 1.156,2.13 false 1.026,1.646 1.148,1.802 0.122,0.156 10 P 1.266,1.733 1.156,1.733 false 1.026,1.25 1.148,1.405 0.122,0.156 10 P 1.266,1.336 1.156,1.336 false 1.026,0.853 1.148,1.009 0.122,0.156 10 P 1.266,0.94 1.156,0.94 false 1.266,0.543 1.156,0.543 false

for 1VD-FTV:

Install the 6 plates, 6 discs and direct clutch flange to the clutch drum.

Install in order:

P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Direct clutch flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



c.
C161655E01
1.266,0.545 1.149,0.545 false 1.266,1.018 1.149,1.018 false 2.279,0.794 2.162,0.794 false 2.279,1.268 2.162,1.268 false 2.279,1.741 2.162,1.741 false 2.279,2.214 2.162,2.214 false 2.279,2.688 2.162,2.688 false 1.266,1.492 1.149,1.492 false 1.266,1.965 1.149,1.965 false 1.266,2.438 1.149,2.438 false 1.266,2.912 1.149,2.912 false 1.014,0.924 1.142,1.090 0.128,0.166 10 P 1.014,1.402 1.142,1.568 0.128,0.166 10 P 1.014,1.88 1.142,2.047 0.128,0.166 10 P 1.014,2.359 1.142,2.525 0.128,0.166 10 P 1.014,2.837 1.142,3.003 0.128,0.166 10 P 2.306,0.706 2.434,0.869 0.128,0.163 10 D 2.306,1.185 2.434,1.348 0.128,0.163 10 D 2.306,1.653 2.434,1.816 0.128,0.163 10 D 2.306,2.132 2.434,2.295 0.128,0.163 10 D 2.306,2.611 2.434,2.774 0.128,0.163 10 D 1.02,0.454 1.148,0.622 0.128,0.168 10 F

for 1UR-FE, 3UR-FE:

Install the 5 plates, 5 discs and direct clutch flange to the clutch drum.

Install in order:

P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Direct clutch flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



d.

Using a screwdriver, install the snap ring to the clutch drum.

NOTICE:

Be careful not to damage the clutch drum.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



e.

Using a dial indicator, measure the moving distance (A) of the direct clutch flange at both ends across the diameter while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) into the oil hole as shown in the illustration. Then choose from the 9 flange thicknesses in the table so that the measured value is within the standard range.

Standard moving distance (A):

0.58 to 0.88 mm (0.0228 to 0.0346 in.)


C358663E01
2.438,2.25 2.719,2.479 2.719,2.479 2.854,2.479 true 2.156,0.896 2.469,1.094 0.313,0.198 10 false *a 2.896,2.365 3.208,2.563 0.313,0.198 10 false *1

Text in Illustration
*1 Oil Hole
*a Distance (A)

Flange Thickness (for 1VD-FTV):
Mark Thickness
0 3.45 to 3.55 mm (0.136 to 0.140 in.)
1 3.55 to 3.65 mm (0.140 to 0.144 in.)
2 3.65 to 3.75 mm (0.144 to 0.148 in.)
3 3.75 to 3.85 mm (0.148 to 0.152 in.)
4 3.85 to 3.95 mm (0.152 to 0.156 in.)
5 3.95 to 4.05 mm (0.156 to 0.159 in.)
6 4.05 to 4.15 mm (0.159 to 0.163 in.)
7 4.15 to 4.25 mm (0.163 to 0.167 in.)
8 4.25 to 4.35 mm (0.167 to 0.171 in.)
A 4.35 to 4.45 mm (0.171 to 0.175 in.)


Flange Thickness (for 1UR-FE, 3UR-FE):
Mark Thickness
0 3.45 to 3.55 mm (0.136 to 0.140 in.)
1 3.55 to 3.65 mm (0.140 to 0.144 in.)
2 3.65 to 3.75 mm (0.144 to 0.148 in.)
3 3.75 to 3.85 mm (0.148 to 0.152 in.)
4 3.85 to 3.95 mm (0.152 to 0.156 in.)
5 3.95 to 4.05 mm (0.156 to 0.159 in.)
6 4.05 to 4.15 mm (0.159 to 0.163 in.)
7 4.15 to 4.25 mm (0.163 to 0.167 in.)
8 4.25 to 4.35 mm (0.167 to 0.171 in.)



f.

Temporarily remove the snap ring, install the selected flange and reinstall the snap ring.


Hide 35048 36.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

C161703E02
1.286,1.662 1.502,1.882 0.216,0.220 10 *1 1.011,1.521 1.25,1.735 false

Text in Illustration
*1 New O-Ring

a.

Coat a new O-ring with ATF and install it to the clutch drum.


b.
C161702E02
1.753,1.827 1.921,1.991 0.168,0.164 10 *1 2.168,1.286 1.916,1.774 false

Coat a new O-ring with ATF and install it to the reverse clutch piston.

Text in Illustration
*1 New O-Ring


c.
C161701

Insert the clutch drum into the reverse clutch piston with both hands.

NOTICE:
·

Be careful not to damage the O-ring.

·

Make sure to align the holes of the reverse clutch piston with those of the clutch drum as shown in the illustration.

·

Make sure to align the protrusions of the reverse clutch piston with the cutout of the clutch drum.




Hide 35688 37.INSTALL NO. 3 CLUTCH BALANCER

C161657E02
1.642,1.818 1.813,1.984 0.170,0.166 10 *1 1.603,1.496 1.739,1.773 false

Text in Illustration
*1 New O-ring

a.

Coat a new O-ring with ATF and install it to the reverse clutch piston.


b.

Install the reverse clutch return spring and No. 3 balancer to the reverse clutch piston.


c.

Place SST on the clutch balancer and compress the clutch balancer with a press.

SST
09380-60010  (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06070, 09381-06080)

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



d.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



e.
C162738

Set the end gap of the snap ring in the piston as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



Hide 35649B 38.SELECT REVERSE CLUTCH FLANGE

a.
C228995E01
1.494,0.379 1.643,0.532 0.149,0.152 10 *1 1.677,0.464 1.722,0.464 1.722,0.464 2.026,0.632 false

Using a screwdriver, install the snap ring to the clutch drum.

Text in Illustration
*1 Protective Tape

NOTICE:
·

Be careful not to damage the clutch drum.

·

Make sure to install the direct clutch and reverse clutch snap rings so that their openings face opposite directions.



HINT:

Wrap the tip of the screwdriver with protective tape before use.



b.
C177410E01
2.106,2.437 2.204,2.437 false 1.076,2.232 1.174,2.232 false 2.24,2.359 2.371,2.523 0.132,0.165 10 D 0.927,2.153 1.059,2.317 0.132,0.165 10 P 1.076,2.82 1.174,2.82 false 0.927,2.74 1.059,2.905 0.132,0.165 10 F 1.076,1.872 1.174,1.872 false 0.927,1.792 1.059,1.957 0.132,0.165 10 P 1.076,1.511 1.174,1.511 false 0.927,1.432 1.059,1.596 0.132,0.165 10 P 1.076,1.151 1.174,1.151 false 0.778,1.071 1.030,1.236 0.252,0.165 10 S/F 2.106,2.072 2.204,2.072 false 2.24,1.993 2.371,2.158 0.132,0.165 10 D 2.106,1.706 2.204,1.706 false 2.24,1.627 2.371,1.792 0.132,0.165 10 D 2.106,1.34 2.204,1.34 false 2.24,1.262 2.371,1.426 0.132,0.165 10 D 2.138,0.971 2.204,0.971 false 2.24,0.892 2.371,1.057 0.132,0.165 10 C

for 1VD-FTV:

Install the flange, 4 discs, 3 plates, selected reverse clutch flange, cushion plate and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - S/F - C


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected reverse clutch flange

C = Cushion plate



c.
C175544E01
2.195,1.092 2.105,1.092 false 2.195,1.453 2.105,1.453 false 2.195,1.813 2.105,1.813 false 2.195,2.173 2.105,2.173 false 2.195,2.534 2.105,2.534 false 1.174,1.276 1.084,1.276 false 1.174,0.915 1.084,0.915 false 1.174,1.636 1.084,1.636 false 1.174,1.997 1.084,1.997 false 1.174,2.357 1.084,2.357 false 1.174,2.801 1.084,2.801 false 2.23,1.005 2.368,1.175 0.138,0.170 10 D 2.195,0.742 2.138,0.742 false 2.234,0.655 2.371,0.826 0.138,0.170 10 C 2.23,1.365 2.368,1.536 0.138,0.170 10 D 2.23,1.726 2.368,1.896 0.138,0.170 10 D 2.23,2.086 2.368,2.256 0.138,0.170 10 D 2.23,2.446 2.368,2.617 0.138,0.170 10 D 0.799,0.835 1.058,1.012 0.258,0.177 10 S/F 0.94,1.195 1.078,1.375 0.138,0.180 10 P 0.94,1.554 1.078,1.735 0.138,0.180 10 P 0.94,1.914 1.078,2.094 0.138,0.180 10 P 0.94,2.274 1.078,2.454 0.138,0.180 10 P 0.94,2.734 1.068,2.892 0.128,0.158 10 F

for 1UR-FE, 3UR-FE:

Install the flange, 5 discs, 4 plates, selected reverse clutch flange, cushion plate and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - P -D - S/F - C


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected reverse clutch flange

C = Cushion plate



d.
C162743

Using a screwdriver, install the snap ring.


e.

Using a dial indicator, measure the moving distance (A minus B) of the top surface of the reverse clutch piston (A) and cushion plate (B) at both ends across the diameter while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) into the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard range.

U165091E01
1.527,0.091 1.732,0.254 0.205,0.163 10 *a 1.028,0.429 1.334,0.17 1.334,0.17 1.49,0.17 false 3.703,1.406 3.871,1.569 0.168,0.163 10 *b 4.698,0.796 4.06,1.481 4.06,1.481 3.982,1.481 false 1.885,1.412 2.082,1.568 0.198,0.156 10 *1 2.102,1.471 2.212,1.471 2.212,1.471 2.342,0.841 false 5.76,1.472 5.869,1.472 5.869,1.472 5.946,0.843 false 5.541,1.408 5.739,1.564 0.198,0.156 10 *1

Standard moving distance (A minus B):
for 1VD-FTV:

0.46 to 0.76 mm (0.0181 to 0.0299 in.)

for 1UR-FE, 3UR-FE:

0.59 to 0.89 mm (0.0232 to 0.0350 in.)


Text in Illustration
*1 Oil Hole - -
*a Distance (A) *b Distance (B)

Flange Thickness:
Mark Thickness
0 2.35 to 2.45 mm (0.0925 to 0.0965 in.)
1 2.45 to 2.55 mm (0.0965 to 0.100 in.)
2 2.55 to 2.65 mm (0.100 to 0.104 in.)
3 2.65 to 2.75 mm (0.104 to 0.108 in.)
4 2.75 to 2.85 mm (0.108 to 0.112 in.)
5 2.85 to 2.95 mm (0.112 to 0.116 in.)
6 2.95 to 3.05 mm (0.116 to 0.120 in.)
7 3.05 to 3.15 mm (0.120 to 0.124 in.)
8 3.15 to 3.25 mm (0.124 to 0.128 in.)
A 3.25 to 3.35 mm (0.128 to 0.132 in.)
B 3.35 to 3.45 mm (0.132 to 0.136 in.)
C 3.45 to 3.55 mm (0.136 to 0.140 in.)



f.
D029843

Remove the snap ring, reverse clutch reaction sleeve and rear clutch disc set from the clutch drum.


Hide 35602A 39.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY

C162744E03
1.956,0.081 2.140,0.247 0.184,0.165 10 *1 2.541,0.811 2.382,0.17 2.382,0.17 2.288,0.17 false

Text in Illustration
*1 New O-Ring

a.

Coat a new O-ring with ATF and install it to the input shaft.


b.
C228998

Install the forward clutch piston to the input shaft.


Hide 35621V 40.INSTALL COAST CLUTCH PISTON

a.
C228997

Install the coast clutch piston to the input shaft.


b.

Coat a new O-ring with ATF and install it to the No. 1 clutch balancer.

Text in Illustration
*1 New O-Ring


c.

Install the forward clutch return spring and No. 1 clutch balancer to the input shaft.

NOTICE:

Be careful not to damage the O-rings.



d.

Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.

SST
09350-30020  (09350-07040)

NOTICE:

Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.



e.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Do not expand the snap ring excessively.



f.
C162759E07
0.698,1.177 0.885,1.396 0.188,0.219 10 false *b 0.698,0.135 0.896,0.323 0.198,0.188 10 false *a

Set the end gap of the snap ring in the balancer as shown in the illustration.

NOTICE:

Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


Text in Illustration
*a Correct
*b Incorrect


Hide 35685 41.INSTALL COAST CLUTCH DISC SET

a.
C177409E01
1.277,1.516 1.414,1.675 0.138,0.158 10 D 0.253,1.661 0.391,1.820 0.138,0.158 10 P 0.253,0.232 0.391,0.391 0.138,0.158 10 F 1.18,1.599 1.262,1.599 false 0.399,1.746 0.481,1.746 false 0.253,1.374 0.391,1.532 0.138,0.158 10 P 0.399,1.459 0.481,1.459 false 0.253,1.087 0.391,1.245 0.138,0.158 10 P 0.399,1.172 0.481,1.172 false 0.253,0.799 0.391,0.958 0.138,0.158 10 P 0.399,0.884 0.481,0.884 false 0.253,0.512 0.391,0.671 0.138,0.158 10 P 0.399,0.597 0.481,0.597 false 0.399,0.314 0.481,0.314 false 1.277,1.229 1.414,1.388 0.138,0.158 10 D 1.18,1.312 1.262,1.312 false 1.277,0.942 1.414,1.100 0.138,0.158 10 D 1.18,1.025 1.262,1.025 false 1.277,0.655 1.414,0.813 0.138,0.158 10 D 1.18,0.738 1.262,0.738 false 1.277,0.367 1.414,0.526 0.138,0.158 10 D 1.18,0.45 1.262,0.45 false

for 1VD-FTV:

Install the 5 plates, 5 discs and coast clutch flange.

Install in order:

P - D - P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.
C162747E01
0.272,0.239 0.402,0.410 0.129,0.171 10 F 0.272,0.577 0.402,0.748 0.129,0.171 10 P 0.272,0.91 0.402,1.081 0.129,0.171 10 P 0.272,1.243 0.402,1.414 0.129,0.171 10 P 0.272,1.622 0.402,1.793 0.129,0.171 10 P 1.283,0.418 1.413,0.588 0.129,0.171 10 D 1.283,0.749 1.413,0.919 0.129,0.171 10 D 1.283,1.08 1.413,1.251 0.129,0.171 10 D 1.283,1.411 1.413,1.582 0.129,0.171 10 D 0.481,0.333 0.409,0.333 false 1.252,0.505 1.18,0.505 false 1.252,0.836 1.18,0.836 false 1.252,1.166 1.18,1.166 false 1.252,1.497 1.18,1.497 false 0.481,0.664 0.409,0.664 false 0.481,0.994 0.409,0.994 false 0.481,1.325 0.409,1.325 false 0.481,1.703 0.409,1.703 false

for 1UR-FE, 3UR-FE:

Install the 4 plates, 4 discs and coast clutch flange.

Install in order:

P - D - P - D - P - D - P - D - F


HINT:

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



c.
C229010E01
2.286,0.44 2.461,0.591 0.174,0.151 10 *1 2.24,0.531 2.154,0.531 2.154,0.531 1.629,0.839 false

Temporarily install the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



d.
U164856E01
1.557,3.38 1.656,3.38 false 1.643,3.125 1.643,3.592 false 2.118,2.505 2.286,2.679 0.168,0.174 10 *a 1.643,3.198 1.948,2.596 1.948,2.596 2.055,2.596 false 2.549,2.163 2.702,2.320 0.152,0.156 10 *1 2.648,1.032 2.363,2.242 2.363,2.242 2.498,2.242 false

Using a dial indicator, measure the moving distance (A) of the coast clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration. Then choose from the 11 flange thicknesses in the table so that the measured value is within the standard range.

Standard moving distance (A):
for 1VD-FTV:

0.51 to 0.81 mm (0.0201 to 0.0319 in.)

for UR Engine Series:

0.41 to 0.71 mm (0.0161 to 0.0280 in.)


Text in Illustration
*1 Oil Hole
*a Distance (A)

Flange Thickness:
Mark Thickness
0 2.95 to 3.05 mm (0.116 to 0.120 in.)
1 3.05 to 3.15 mm (0.120 to 0.124 in.)
2 3.15 to 3.25 mm (0.124 to 0.128 in.)
3 3.25 to 3.35 mm (0.128 to 0.132 in.)
4 3.35 to 3.45 mm (0.132 to 0.136 in.)
5 3.45 to 3.55 mm (0.136 to 0.140 in.)
6 3.55 to 3.65 mm (0.140 to 0.144 in.)
7 3.65 to 3.75 mm (0.144 to 0.148 in.)
8 3.75 to 3.85 mm (0.148 to 0.152 in.)
A 3.85 to 3.95 mm (0.152 to 0.156 in.)
B 3.95 to 4.05 mm (0.156 to 0.159 in.)



e.

Temporarily remove the snap ring, install the selected coast clutch flange and reinstall the snap ring.

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 35633B 42.INSTALL FORWARD MULTIPLE DISC CLUTCH DISC SET

a.
C163078E01
1.241,0.486 1.06,0.486 false 1.244,0.865 1.063,0.865 false 1.247,1.243 1.066,1.243 false 1.249,1.621 1.068,1.621 false 1.244,1.99 1.063,1.99 false 1.244,2.365 1.063,2.365 false 1.244,2.74 1.063,2.74 false 1.244,2.925 1.063,2.925 false 0.886,0.408 1.028,0.588 0.141,0.180 10 F 0.886,0.784 1.028,0.964 0.141,0.180 10 P 0.886,1.16 1.028,1.340 0.141,0.180 10 P 0.886,1.536 1.028,1.716 0.141,0.180 10 P 0.886,1.912 1.028,2.092 0.141,0.180 10 P 0.886,2.288 1.028,2.468 0.141,0.180 10 P 0.886,2.664 1.028,2.844 0.141,0.180 10 P 0.886,2.849 1.028,3.029 0.141,0.180 10 C 2.353,0.67 2.172,0.67 false 2.353,1.046 2.172,1.046 false 2.354,1.421 2.173,1.421 false 2.354,1.797 2.173,1.797 false 2.354,2.173 2.173,2.173 false 2.354,2.548 2.173,2.548 false 2.417,0.585 2.560,0.763 0.143,0.178 10 D 2.417,0.961 2.560,1.140 0.143,0.178 10 D 2.417,1.338 2.560,1.516 0.143,0.178 10 D 2.417,1.714 2.560,1.892 0.143,0.178 10 D 2.417,2.09 2.560,2.268 0.143,0.178 10 D 2.417,2.466 2.560,2.644 0.143,0.178 10 D

Install the cushion plate, 6 plates, 6 discs and flange to the input shaft.

Install in order:

C - P - D - P - D - P - D - P - D - P - D - P - D - F


HINT:

C = Cushion plate

P = Plate

D = Disc

F = Flange


NOTICE:

Before assembling new discs, soak them in ATF for at least 2 hours.



b.
C229011E01
1.708,0.271 1.857,0.420 0.149,0.149 10 *1 1.674,0.357 1.596,0.357 1.596,0.357 1.39,0.604 false

Temporarily install the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



c.
U164855E01
1.67,2.477 1.67,2.944 false 1.781,2.653 1.962,2.825 0.182,0.171 10 *a 2.653,2.062 2.845,2.214 0.192,0.152 10 *1 2.64,1.131 2.402,2.14 2.402,2.14 2.537,2.14 false 1.486,2.733 1.718,2.733 false

Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard range.

Standard moving distance (A):

0.85 to 1.15 mm (0.0335 to 0.0453 in.)


Text in Illustration
*1 Oil Hole
*a Distance (A)

Flange Thickness:
Mark Thickness
0 2.95 to 3.05 mm (0.116 to 0.120 in.)
1 3.05 to 3.15 mm (0.120 to 0.124 in.)
2 3.15 to 3.25 mm (0.124 to 0.128 in.)
3 3.25 to 3.35 mm (0.128 to 0.132 in.)
4 3.35 to 3.45 mm (0.132 to 0.136 in.)
5 3.45 to 3.55 mm (0.136 to 0.140 in.)
6 3.55 to 3.65 mm (0.140 to 0.144 in.)
7 3.65 to 3.75 mm (0.144 to 0.148 in.)
8 3.75 to 3.85 mm (0.148 to 0.152 in.)
A 3.85 to 3.95 mm (0.152 to 0.156 in.)
B 3.95 to 4.05 mm (0.156 to 0.159 in.)
C 4.05 to 4.15 mm (0.159 to 0.163 in.)



d.

Temporarily remove the snap ring, install the selected flange and reinstall the snap ring.

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 35790H 43.INSTALL NO. 4 1-WAY CLUTCH ASSEMBLY

a.

Install the No. 2 clutch hub thrust washer to the coast clutch hub.

HINT:

Use a small amount of MP grease to make the No. 2 clutch hub thrust washer stay securely in place.



b.

Install the No. 4 1-way clutch assembly to the coast clutch hub.


Hide 35064 45.INSTALL COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

a.
C163077E07
1.865,0.198 2.25,0.198 false 1.823,1.229 2.25,1.229 false 1.823,1.01 2.25,0.896 false 2.292,1.146 2.979,1.354 0.688,0.208 10 false *1 2.292,0.094 2.969,0.292 0.677,0.198 10 false *3 2.292,0.75 2.823,0.938 0.531,0.188 10 false *2

Install the 2 thrust needle roller bearings, thrust bearing race and coast clutch hub with the No. 4 1-way clutch assembly to the input shaft.

Text in Illustration
*1 Bearing C
*2 Race
*3 Bearing D

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings and thrust bearing race stay securely in place.


Bearing and Race Diameter:
Item Inside Outside
Bearing C 21.05 to 21.3 mm (0.829 to 0.839 in.) 39.63 to 39.88 mm (1.56 to 1.57 in.)
Race 22.8 to 23.1 mm (0.898 to 0.909 in.) 44.5 to 44.75 mm (1.75 to 1.76 in.)
Bearing D 39.45 to 39.7 mm (1.55 to 1.56 in.) 60.5 to 60.75 mm (2.38 to 2.39 in.)



Hide 35712A 46.INSTALL INPUT SHAFT OIL SEAL RING

a.
C162568E02
0.633,0.008 0.823,0.199 0.190,0.191 10 *a 0.633,1.121 0.823,1.309 0.190,0.189 10 *b

Overlap the seal ring edges in the axial direction.

Text in Illustration
*a Correct
*b Incorrect

NOTICE:
·

Overlapping the seal ring edges in the axial direction prevents damage to the seal ring.

·

Do not overlap the seal ring edges in the radial direction, as this may damage the seal ring.




b.
C161649E02
0.943,0.169 1.197,0.409 0.254,0.240 10 *1 0.677,0.84 0.468,1.411 false 0.677,0.84 0.788,0.261 0.788,0.261 0.898,0.261 false 0.677,0.84 1.036,1.252 false 0.653,1.355 0.677,0.84 false 0.837,1.306 0.677,0.84 false

Coat 4 new oil seal rings with ATF.

Text in Illustration
*1 New O-Ring


c.

Squeeze the ends of the 4 oil seal rings together, and then install them to the input shaft groove.

NOTICE:

Do not excessively widen the rings.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 35701 47.INSTALL INPUT SHAFT ASSEMBLY

a.

Install the input shaft to the clutch drum.


Hide 35061 48.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.

Install the No. 3 clutch hub thrust washer, forward clutch hub and thrust needle roller bearing to the clutch drum.

NOTICE:

Before installing the forward clutch hub, apply ATF to the sliding surfaces of the forward clutch hub bush. After the installation, check that the forward clutch hub rotates smoothly.


HINT:

Use a small amount of MP grease to make the thrust needle roller bearing and No. 3 clutch hub thrust washer stay securely in place.


Bearing Diameter:
Item Inside Outside
Bearing 46.45 to 46.7 mm (1.83 to 1.84 in.) 64.3 to 64.55 mm (2.53 to 2.54 in.)



Hide 35049 49.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

a.

Install the reverse clutch hub to the clutch drum.

NOTICE:

Before installing of the reverse clutch hub, apply ATF to the sliding surfaces of the reverse clutch hub bush. After the installation, check that the reverse clutch rotates smoothly.



Hide 35677C 50.INSTALL REAR CLUTCH DISC SET

a.

Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the clutch drum.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



b.
C177406E01
2.505,2.225 2.636,2.392 0.131,0.167 10 D 0.819,2.34 0.949,2.507 0.131,0.167 10 F 2.301,2.306 2.46,2.306 false 1.123,2.423 0.964,2.423 false 0.819,2.043 0.949,2.210 0.131,0.167 10 P 1.123,2.126 0.964,2.126 false 0.819,1.747 0.949,1.914 0.131,0.167 10 P 1.123,1.83 0.964,1.83 false 0.819,1.45 0.949,1.617 0.131,0.167 10 P 1.123,1.533 0.964,1.533 false 0.681,1.154 0.923,1.321 0.242,0.167 10 S/F 1.123,1.237 0.964,1.237 false 0.819,0.954 0.949,1.121 0.131,0.167 10 C 1.123,1.037 0.964,1.037 false 2.505,1.929 2.636,2.096 0.131,0.167 10 D 2.301,2.01 2.46,2.01 false 2.505,1.632 2.636,1.799 0.131,0.167 10 D 2.301,1.713 2.46,1.713 false 2.505,1.336 2.636,1.502 0.131,0.167 10 D 2.301,1.417 2.46,1.417 false

for 1VD-FTV:

Install the flange, 4 discs, 3 plates, selected reverse clutch flange and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - S/F - C


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected reverse clutch flange

C = Cushion plate



c.
C175546E01
1.123,1.063 0.966,1.063 false 2.457,1.214 2.3,1.214 false 2.457,1.511 2.3,1.511 false 2.457,1.807 2.3,1.807 false 2.457,2.104 2.3,2.104 false 2.457,2.4 2.3,2.4 false 1.124,1.367 0.966,1.367 false 1.123,1.656 0.966,1.656 false 1.123,1.953 0.966,1.953 false 1.124,2.249 0.966,2.249 false 1.123,2.546 0.966,2.546 false 0.678,0.984 0.925,1.155 0.247,0.171 10 S/F 0.817,1.281 0.960,1.452 0.142,0.171 10 P 0.817,1.568 0.960,1.739 0.142,0.171 10 P 0.817,1.875 0.960,2.047 0.142,0.171 10 P 0.817,2.173 0.960,2.344 0.142,0.171 10 P 0.817,2.47 0.960,2.641 0.142,0.171 10 F 2.489,1.127 2.635,1.303 0.146,0.176 10 D 2.457,0.867 2.33,0.867 false 2.489,0.779 2.635,0.955 0.146,0.176 10 C 2.489,1.425 2.635,1.601 0.146,0.176 10 D 2.489,1.723 2.635,1.899 0.146,0.176 10 D 2.489,2.021 2.635,2.196 0.146,0.176 10 D 2.489,2.319 2.635,2.494 0.146,0.176 10 D

for 1UR-FE, 3UR-FE:

Install the flange, 5 discs, 4 plates, selected reverse clutch flange and reverse clutch reaction sleeve to the clutch drum.

Install in order:

F - D - P - D - P - D - P - D - P - D - S/F - C


HINT:

F = Flange

D = Disc

P = Plate

S/F = Selected reverse clutch flange

C = Cushion plate



d.

Using a screwdriver, install the snap ring to the clutch drum.


Hide 35780B 51.INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

a.

Install the clutch drum thrust washer to the clutch drum.

HINT:

Use a small amount of MP grease to make the clutch drum thrust washer stay securely in place.



b.

Install the 1-way clutch to the clutch drum.


Hide 53.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161633E07
0.667,0.292 0.552,0.292 0.552,0.292 0.375,1.177 false 0.938,1.823 0.813,1.823 0.813,1.823 0.76,1.542 false 0.719,0.198 1.396,0.438 0.677,0.24 10 false *1 0.958,1.708 1.635,1.948 0.677,0.24 10 false *2

Text in Illustration
*1 Bearing A
*2 Bearing B

a.

Install the 2 thrust needle roller bearings.

HINT:

Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.


Bearing Diameter:
Item Inside Outside
Bearing A 71.96 to 72.26 mm (2.83 to 2.84 in.) 85.25 to 85.6 mm (3.36 to 3.37 in.)
Bearing B 36.45 to 36.7 mm (1.44 to 1.45 in.) 52.96 to 53.26 mm (2.09 to 2.10 in.)



b.

Coat the clutch drum thrust washer with petroleum jelly and install it to the clutch drum and input shaft assembly.


c.

Install the clutch drum and input shaft assembly to the transmission case.


Hide 54.INSTALL OIL PUMP ASSEMBLY

C161631E02
2.359,1.675 2.537,1.825 0.178,0.151 10 *3 2.04,1.616 2.322,1.743 false 1.053,0.278 1.314,0.432 0.261,0.154 10 *2 0.44,0.104 0.304,0.104 0.304,0.104 0.166,1.656 false 0.98,0.361 0.845,0.361 0.845,0.361 0.75,1.416 false 0.495,0.024 0.656,0.166 0.161,0.141 10 *1

Text in Illustration
*1 Race A
*2 Race B
*3 New O-Ring

a.

Coat a new O-ring with ATF and install it to the oil pump assembly.


b.

Install the 2 thrust bearing races to the front oil pump assembly.

Thrust Bearing Race Diameter:
Item Inside Outside
Race A 74.26 to 74.56 mm (2.92 to 2.94 in.) 87.39 to 87.74 mm (3.44 to 3.45 in.)
Race B 38.0 to 38.3 mm (1.50 to 1.51 in.) 53.9 to 54.1 mm (2.12 to 2.13 in.)



c.

Pass the input shaft through the center hole of the oil pump assembly, and align the bolt holes of the oil pump assembly with the transmission case.


d.

Hold the input shaft and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.


e.

Apply seal packing to the flanges of the bolts.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Do not allow seal packing to contact the bolt threads.



f.

Install the 10 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

During installation, do not allow oil to contact the bolts or the surface of the oil pump body.



Hide 35506F 56.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

C161808E03
2.542,0.563 2.031,1.031 false 2.552,0.375 2.885,0.573 0.333,0.198 10 true SST

a.

Using SST, tap in 2 new oil seals.

SST
09350-30020  (09350-07110)


b.

Coat the lips of the oil seals with MP grease.


Hide 35505 57.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

C161809E02
0.688,0.063 0.897,0.229 0.209,0.166 10 *1 0.977,1.074 1.159,0.154 1.159,0.154 1.051,0.154 false

Text in Illustration
*1 New Spacer

a.

Install a new spacer to the manual valve lever sub-assembly.


b.

Push the manual valve lever shaft through the transmission case and install the manual valve lever sub-assembly to the manual valve lever shaft.


c.
C161627

Using a hammer, tap in a new spring pin.


d.

Align the manual valve lever indentation with the spacer hole and stake them together with a punch.


e.

Check that the shaft rotates smoothly.


Hide 35557 58.INSTALL PARKING LOCK PAWL

a.

Install a new E-ring to the shaft.


b.

Install the parking lock pawl, shaft and spring.


Hide 35501 59.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.

Connect the parking lock rod to the manual valve lever sub-assembly.


Hide 35595 60.INSTALL PARKING LOCK PAWL BRACKET

a.

Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.
C162752E04
0.802,1.625 0.802,1.792 false 0.792,1.281 0.667,0.219 0.667,0.219 0.823,0.219 false 0.698,1.802 0.958,1.99 0.26,0.188 10 false *1 0.865,0.115 1.073,0.281 0.208,0.167 10 false *2

Move the manual valve lever sub-assembly to the P position and confirm that the planetary ring gear is correctly locked by the lock pawl.

Text in Illustration
*1 Lock Pawl
*2 Rear Planetary Gear


Hide 35424F 61.INSTALL B-1 ACCUMULATOR VALVE

C162753

a.

Install the 2 springs and accumulator valve to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
B-1 Inner 44.98 mm (1.77 in.)
11.30 mm (0.445 in.)
Natural
B-1 Outer 46.36 mm (1.83 in.)
17.10 mm (0.673 in.)
Natural



Hide 35426D 62.INSTALL C-3 ACCUMULATOR PISTON

C162754E04
2.104,0.25 2.792,0.323 false 1.99,0.24 2.063,0.25 false 1.594,0.302 1.188,0.156 1.188,0.156 1.875,0.229 false 2.063,0.469 1.646,0.323 false 2.844,0.75 2.115,0.49 false 0.896,0.063 1.156,0.25 0.26,0.188 10 true *1

Text in Illustration
*1 New O-Ring

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-3 76.65 mm (3.02 in.)
20.1 mm (0.791 in.)
for 1VD-FTV:
White
for 1UR-FE, 3UR-FE:
Natural



Hide 35427K 63.INSTALL B-3 ACCUMULATOR PISTON

C162755E04
2.125,0.5 2.854,0.729 false 1.594,0.344 2.083,0.49 false 1.781,0.26 1.219,0.229 1.219,0.229 1.521,0.323 false 2.083,0.271 1.875,0.26 false 2.802,0.313 2.125,0.281 false 0.885,0.156 1.146,0.396 0.26,0.24 10 true *1

Text in Illustration
*1 New O-Ring

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
B-3 64.50 mm (2.54 in.)
19.5 mm (0.768 in.)
Orange



Hide 35425A 64.INSTALL C-2 ACCUMULATOR PISTON

C162756E04
2.177,0.24 2.833,0.323 false 2.063,0.229 2.083,0.229 false 1.719,0.26 1.51,0.156 1.51,0.156 1.938,0.208 false 2.104,0.427 1.802,0.292 false 2.875,0.792 2.167,0.458 false 1.135,0.073 1.438,0.292 0.302,0.219 10 true *1

Text in Illustration
*1 New O-Ring

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Spring Diameter:
Spring Free Length
Outer Diameter
Color
C-2 68.0 mm (2.68 in.)
16.1 mm (0.634 in.)
for 1VD-FTV:
Blue
for 1UR-FE, 3UR-FE:
Light green



Hide 35251 65.INSTALL CHECK BALL BODY

a.

Install the spring and check ball body.


Hide 35159 66.INSTALL BRAKE DRUM GASKET

C161617E04
1.667,0.354 1.406,0.865 1.406,0.865 0.823,0.302 false 1.406,0.865 1.563,1.292 1.563,1.292 1.708,1.292 false 1.771,1.229 1.99,1.396 0.219,0.167 10 true *1

Text in Illustration
*1 New O-Ring

a.

Install 3 new brake drum gaskets.


Hide 35145C 67.INSTALL TRANSMISSION CASE GASKET

C161616E04
0.958,0.438 1.229,0.438 false 1.26,0.333 1.49,0.573 0.229,0.24 10 true *1

Text in Illustration
*1 New O-Ring

a.

Install 3 new transmission case gaskets.


Hide 35410 68.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

C162146E04
1.896,1.229 2.396,0.698 false 2.417,0.542 2.646,0.771 0.229,0.229 10 true *1

Text in Illustration
*1 Pin

a.

Align the hole of the manual valve with the pin of the lever.


b.
C162147E05
1.01,0.156 0.906,0.26 false 0.573,0.24 0.458,0.146 false 0.625,0.573 0.26,0.656 0.26,0.656 0.604,1.135 false 0.615,0.75 0.26,0.656 false 0.521,1.427 0.229,1.438 0.229,1.438 0.49,1.552 false 0.927,1.76 1.063,1.917 false 1.927,1.677 1.833,1.917 1.833,1.917 2.208,1.74 false 2.865,1.656 2.729,1.792 2.729,1.792 2.615,1.719 false 3.156,1.24 3.25,1.365 3.25,1.365 3.219,1.563 false 3.25,1.375 3.177,1.365 false 3.26,0.844 3.177,0.844 false 3.24,0.635 3.167,0.635 false 1.917,1.427 1.75,1.427 false 2.594,1.365 2.594,1.229 false 0.104,0.563 0.26,0.74 0.156,0.177 10 false A 0.073,1.354 0.208,1.531 0.135,0.177 10 true B 0.323,0.021 0.458,0.198 0.135,0.177 10 true B 1.063,0.031 1.198,0.208 0.135,0.177 10 true B 1.104,1.865 1.24,2.031 0.135,0.167 10 true B 1.688,1.906 1.823,2.083 0.135,0.177 10 false B 2.729,1.802 2.865,1.979 0.135,0.177 10 true B 3.281,1.281 3.417,1.458 0.135,0.177 10 false B 3.292,0.76 3.427,0.938 0.135,0.177 10 false D 2.531,1.042 2.667,1.219 0.135,0.177 10 true D 3.281,0.552 3.427,0.719 0.146,0.167 10 false C 1.563,1.354 1.708,1.521 0.146,0.167 10 true C

Install the 19 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

36 mm (1.42 in.) for bolt A

25 mm (0.984 in.) for bolt B

45 mm (1.77 in.) for bolt C

50 mm (1.97 in.) for bolt D



c.

Install the detent spring and detent spring cover with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 82125K 69.INSTALL NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE

C161615E02
1.914,0.752 2.084,0.913 0.170,0.161 10 *1 0.883,0.477 0.711,0.62 false 2.247,0.621 2.112,0.733 false 0.504,0.627 0.674,0.788 0.170,0.161 10 *1

Text in Illustration
*1 New O-Ring

a.

Install 2 new O-rings to the transmission wires.


b.

Install the transmission wire harnesses.


c.

Install the No. 1 transmission wire and No. 2 transmission wire with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
U164570E02
1.198,0.896 0.719,0.604 false 1.135,1.167 0.51,1.229 false 0.448,0.479 0.656,0.698 0.208,0.219 10 true *a 0.271,1.156 0.479,1.365 0.208,0.208 10 true *b 0.823,0.406 0.958,0.583 0.135,0.177 10 true A 0.698,1.375 0.833,1.552 0.135,0.177 10 true B

Connect the 9 connectors to the solenoid valves.

Text in Illustration
*a Orange
*b Blue


e.

Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 11 N*m (112 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

12 mm (0.472 in.) for bolt A

36 mm (1.42 in.) for bolt B



Hide 35330 70.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C178807

a.

Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.


b.

Install the valve body oil strainer assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35106 71.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C178809E04
0.399,0.041 0.557,0.194 0.158,0.153 10 *1 0.658,0.11 0.804,0.11 0.804,0.11 2.202,1.029 false 1.701,1.018 0.804,0.11 false 1.037,0.76 0.804,0.11 false 1.019,1.275 0.804,0.11 false

Text in Illustration
*1 Magnet

a.

Install the 4 magnets.


b.

Install a new gasket to the oil pan.


c.

Install the oil pan with the 12 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:
·
C157303E02
0.694,0.247 0.897,0.413 0.203,0.165 10 *a 2.099,0.247 2.310,0.403 0.211,0.156 10 *b 2.374,2.599 2.599,2.757 0.225,0.158 10 *2 2.584,3.417 2.796,3.607 0.213,0.191 10 *1 1.899,3.782 2.416,3.507 2.416,3.507 2.544,3.507 false


·

Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.

·

Install the gasket so that there is no slack in the gasket, and make sure the entire circumference of the seal surface is level.

·

Make sure that the 9 gasket drop prevention protrusions are attached to the oil pan.

·

When tightening the bolts of the oil pan, make sure that the gasket is not pinched between the gasket tightening area sleeve and the transmission seal surface.



Text in Illustration
*1 Sleeve
*2 Protrusion
*a Correct
*b Incorrect


d.

Install the drain plug.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35015E 72.INSTALL TRANSFER CASE ADAPTER RADIAL BALL BEARING

a.

Using SST and a press, press in the bearing until it stops.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


b.

Using a screwdriver, install the snap ring.


Hide 35015J 73.INSTALL TRANSMISSION CASE ADAPTER OIL SEAL

C177436E04
0.047,1.107 0.373,1.275 0.326,0.168 10 SST 1.232,1.034 0.43,1.177 false 2.405,0.76 2.643,0.964 0.238,0.205 10 *a

Text in Illustration
*a 0 to 1 mm

a.

Coat the lip of a new oil seal with ATF.


b.

Using SST and a hammer, tap in the oil seal.

Standard depth:

0 to 1 mm (0 to 0.0394 in.)


SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35015G 74.INSTALL REAR TRANSFER ADAPTER

C161783E02
2.292,0 2.501,0.177 0.209,0.177 10 *1 2.28,0.103 2.044,0.37 false 1.539,1.856 1.792,2.049 0.253,0.193 10 *a

Text in Illustration
*1 Seal Packing
*a Seal Diameter: 1 to 1.5 mm

a.

Clean the threads of the bolts and case with non-residue solvent.


b.

Apply seal packing to the rear transfer adapter.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent


Seal diameter:

1.0 to 1.5 mm (0.0394 to 0.0591 in.)



c.

Install the rear transfer adapter with the 10 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)


Hide 35111 75.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.

Clean the threads of the bolts and case with non-residue solvent.


b.

Install the transmission housing with the 14 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)


Hide 35122 76.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

a.

Coat a new O-ring with ATF and install it to the breather tube.


b.

Install the breather tube with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 32921C 78.INSTALL OIL COOLER TUBE UNION (w/o ATF Warmer)

a.

Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.


b.
U164860E01
2.767,2.791 2.923,2.972 0.156,0.181 10 *a 3.263,2.461 3.029,2.893 3.029,2.893 2.955,2.893 false

Using a union nut wrench, install the 2 oil cooler tube unions.

Text in Illustration
*a -2 to 2°

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 89413B 79.INSTALL SPEED SENSOR

a.

Coat 2 new O-rings with ATF and install them to the speed sensors.


b.

Install the 2 speed sensors.


c.

Install the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 84540 80.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


a.

Clean the bolt and the bolt hole.


b.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Temporarily install the park/neutral position switch assembly to the automatic transmission case subassembly with the bolt.


d.

Install a new lock washer and the nut to the park/ neutral position switch assembly.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


e.

Temporarily install the transmission control shaft lever RH.


f.
C172409E01
1.013,0.171 1.156,0.338 0.143,0.167 10 P 1.758,0 1.900,0.164 0.141,0.164 10 N 1.512,0.293 1.654,0.456 0.142,0.163 10 R

Using the transmission control shaft lever RH, turn the manual lever shaft all the way back and then forward 2 notches to select the N position.


g.

Remove the control shaft lever RH.


h.
U165763E02
1.979,1.552 0.698,1.229 0.698,1.229 0.542,1.229 false 1.969,0.927 2.656,1.292 2.656,1.292 2.833,1.292 false 2.885,1.219 3.052,1.375 0.167,0.156 10 false *1 0.25,1.156 0.427,1.302 0.177,0.146 10 false *2

Align the groove with the neutral basic line.

Text in Illustration
*1 Neutral Basic Line
*2 Groove


i.

Hold the switch in position and tighten the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


j.
D027990

Using a screwdriver, bend the tabs of the lock washer.


Hide 35572 81.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

a.

Install the transmission control shaft lever RH with the washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)