1. BEARING POSITION
| Mark | Front Race Diameter Inside / Outside | Thrust Bearing Diameter Inside / Outside | Rear Race Diameter Inside / Outside |
|---|---|---|---|
| A | 74.26 to 74.56 mm (2.92 to 2.94 in.) / 87.39 to 87.74 mm (3.44 to 3.45 in.) | 71.96 to 72.26 mm (2.83 to 2.84 in.) / 85.25 to 85.6 mm (3.36 to 3.37 in.) | - |
| B | 38.0 to 38.3 mm (1.50 to 1.51 in.) / 53.9 to 54.1 mm (2.12 to 2.13 in.) | 36.45 to 36.7 mm (1.44 to 1.45 in.) / 52.96 to 53.26 mm (2.09 to 2.10 in.) | - |
| C | - | 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.63 to 39.88 mm (1.56 to 1.57 in.) | 22.8 to 23.1 mm (0.898 to 0.909 in.) / 44.5 to 44.75 mm (1.75 to 1.76 in.) |
| D | - | 39.45 to 39.7 mm (1.55 to 1.56 in.) / 60.5 to 60.75 mm (2.38 to 2.39 in.) | - |
| E | - | 46.45 to 46.7 mm (1.83 to 1.84 in.) / 64.3 to 64.55 mm (2.53 to 2.54 in.) | - |
| F | 55.0 to 55.2 mm (2.165 to 2.173 in.) / 68.8 to 69.3 mm (2.71 to 2.73 in.) | 54.55 to 54.8 mm (2.15 to 2.16 in.) / 70.0 to 70.5 mm (2.76 to 2.78 in.) | - |
| G | - | 65.35 to 65.6 mm (2.57 to 2.58 in.) / 85.6 to 85.95 mm (3.37 to 3.38 in.) | 62.85 to 63.1 mm (2.47 to 2.48 in.) / 82.3 to 82.6 mm (3.24 to 3.25 in.) |
| H | 39.67 to 39.87 mm (1.56 to 1.57 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.) | 36.45 to 36.61 mm (1.437 to 1.441 in.) / 56.62 to 56.92 mm (2.23 to 2.24 in.) | 36.45 to 36.7 mm (1.435 to 1.445 in.) / 56.5 to 57.0 mm (2.22 to 2.24 in.) |
| I | 21.05 to 21.3 mm (0.829 to 0.839 in.) / 39.5 to 39.8 mm (1.56 to 1.57 in.) | 23.2 to 23.4 mm (0.913 to 0.921 in.) / 43.9 to 44.15 mm (1.73 to 1.74 in.) | - |
| J | - | 43.6 to 43.85 mm (1.72 to 1.73 in.) / 62.3 to 62.8 mm (2.45 to 2.47 in.) | 47.15 to 47.4 mm (1.86 to 1.87 in.) / 66.9 to 67.1 mm (2.63 to 2.64 in.) |
35623H
2.INSTALL 1ST AND REVERSE BRAKE PISTON
Coat 3 new O-rings with ATF and install them to the 1st and reverse brake piston.
| *1 | New O-Ring |
Install the 1st and reverse brake piston to the transmission case.
Be careful not to damage the O-ring.
Make sure that the parking hole of the brake piston is on the bottom by engaging the brake piston protrusion and the transmission case spline grooves.
| *1 | Protrusion |
| *2 | Parking Hole |
35068
3.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place the 1st and reverse brake return spring onto the 1st and reverse brake piston.
Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.
Using SST, install the snap ring.
35689A
4.SELECT NO. 4 BRAKE FLANGE
Measure distance A (from the tip of the 1st and reverse brake piston to the step in the transmission case) in the illustration.*1
| *1 | 1st and Reverse Brake Piston |
Standard distance A: 27.82 to 28.42 mm (1.10 to 1.11 in.)
Assemble the flange, No. 4 brake flange, 7 No. 4 brake discs and 6 plates, and measure distance B in the illustration.*2
| *1 | No. 4 Brake Disc |
| *2 | Plate |
| *3 | No. 4 Brake Flange |
| *a | Selected No. 4 brake flange |
Standard distance B: 25.98 to 27.01 mm (1.03 to 1.06 in.)
Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 4 brake flange indicated by the graph point.
Measure length H of the selected No. 4 brake flange as shown in the illustration.
Make sure that when the B measurement and the H dimension of the selected No. 4 brake flange are subtracted from the A measurement, the value is 0.961 to 1.261 mm (0.0379 to 0.0496 in.).
| *a | Mark 0 | *b | Mark 1 |
| *c | Mark 3 | *d | Mark 4 |
| *e | Mark 5 | *f | Mark 7 |
| *g | Mark 8 | *h | Mark 10 |
| *i | Mark 11 | *j | Distance A mm (in.) |
| *k | Distance B mm (in.) | - | - |
| Mark | Length H |
|---|---|
| 0 | 0 mm (0 in.) |
| 1 | 0.09 to 0.25 mm (0.00355 to 0.00984 in.) |
| 3 | 0.23 to 0.39 mm (0.00906 to 0.0153 in.) |
| 4 | 0.37 to 0.53 mm (0.0146 to 0.0208 in.) |
| 5 | 0.51 to 0.67 mm (0.0201 to 0.0263 in.) |
| 7 | 0.65 to 0.81 mm (0.0256 to 0.0318 in.) |
| 8 | 0.79 to 0.95 mm (0.0312 to 0.0374 in.) |
| 10 | 0.93 to 1.09 mm (0.0367 to 0.0429 in.) |
| 11 | 1.07 to 1.23 mm (0.0422 to 0.0484 in.) |
35760
5.INSTALL REAR PLANETARY GEAR ASSEMBLY
Install the thrust bearing race.
| *1 | Race J |
Use a small amount of MP grease to make the thrust bearing race stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Race J | 47.15 to 47.4 mm (1.86 to 1.87 in.) | 66.9 to 67.1 mm (2.63 to 2.64 in.) |
Install the 2 thrust needle roller bearings to the rear planetary gear assembly.
| Item | Inside | Outside |
|---|---|---|
| Bearing I | 23.2 to 23.4 mm (0.913 to 0.921 in.) | 43.9 to 44.15 mm (1.73 to 1.74 in.) |
| Bearing J | 43.6 to 43.85 mm (1.72 to 1.73 in.) | 62.3 to 62.8 mm (2.45 to 2.47 in.) |
| *1 | Bearing I |
| *2 | Bearing J |
Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.
Install the rear planetary gear assembly.
35639B
6.INSTALL BRAKE PLATE STOPPER SPRING
35761
7.INSTALL REAR PLANETARY RING GEAR
Install the rear planetary ring gear flange to the rear planetary ring gear.
Using a screwdriver, install the snap ring.
Install the 3 thrust bearing races, thrust needle roller bearing and rear planetary ring gear together with the rear planetary ring gear flange to the intermediate shaft.
| *1 | Front Race H |
| *2 | Bearing H |
| *3 | Rear Race H |
| *4 | Race I |
Use a small amount of MP grease to make the thrust needle roller bearings and races stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Front race H | 39.67 to 39.87 mm (1.56 to 1.57 in.) | 56.5 to 57.0 mm (2.22 to 2.24 in.) |
| Bearing H | 36.45 to 36.61 mm (1.437 to 1.441 in.) | 56.62 to 56.92 mm (2.23 to 2.24 in.) |
| Rear race H | 36.45 to 36.7 mm (1.435 to 1.445 in.) | 56.5 to 57.0 mm (2.22 to 2.24 in.) |
| Race I | 21.05 to 21.3 mm (0.829 to 0.839 in.) | 39.5 to 39.8 mm (1.56 to 1.57 in.) |
35713
8.INSTALL INTERMEDIATE SHAFT WITH REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR
Install the intermediate shaft together with the rear planetary ring gear flange and rear planetary ring gear to the transmission case.
35684
9.INSTALL NO. 4 BRAKE DISC
Install the flange, 7 discs, 6 plates and selected No. 4 brake flange.
F - D - P - D - P - D - P - D - P - D - P - D - P - D - S/F
F = Flange
D = Disc
P = Plate
S/F = Selected No. 4 brake flange
Before assembling new discs, soak them in ATF for at least 2 hours.
35797B
10.INSTALL 1-WAY CLUTCH INNER RACE
| *a | Front |
Install the No. 3 1-way clutch inner race to the No. 3 1-way clutch assembly.
Be sure to install the 1-way clutch inner race so that it is facing in the proper direction.
35770C
11.INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY
35770C
12.INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY
Install the No. 3 1-way clutch assembly to the transmission case.
Using SST, install the snap ring.
35622G
13.INSTALL NO. 2 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.
| *1 | New O-ring |
Press the No. 2 brake piston into the No. 2 brake cylinder with both hands.
Be careful not to damage the O-rings.
35699
14.INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON
Install the No. 2 brake cylinder with No. 2 brake piston to the transmission case.
When installing the No. 2 brake cylinder with No. 2 brake piston to the transmission case, align the cylinder claw with the groove in the top of the case.
Make sure the No. 2 brake cylinder with No. 2 brake piston is securely inserted into the transmission case.
35678B
15.SELECT NO. 2 BRAKE FLANGE
Install the No. 2 brake piston return spring and flange to the No. 2 brake piston.
Place SST on the No. 2 brake flange and compress the No. 2 brake piston return spring.
Using a screwdriver, install the snap ring to the transmission case.
Measure distance A (from the top surface of the snap ring to the top surface of the No. 2 brake piston return spring) in the illustration.*1
| *1 | No. 2 Brake Piston Return Spring |
Standard distance A: 21.00 to 21.76 mm (0.834 to 0.857 in.)
Assemble the 4 discs, 3 plates and flange as shown in the illustration. Then, with a fixture of 165.2 mm (6.50 in.) or less placed on the flange, measure distance B.*2
| *1 | Flange |
| *2 | Plate |
| *3 | Disc |
| *a | Fixture |
| *b | 165.2 mm or less |
Standard distance B: 16.54 to 17.15 mm (0.651 to 0.675 in.)
Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 2 brake flange indicated by the graph point.
| *1 | Mark 0 | *2 | Mark 1 |
| *3 | Mark 2 | *4 | Mark 3 |
| *5 | Mark 4 | *6 | Mark 5 |
| *7 | Mark 6 | *8 | Mark 7 |
| *a | Distance A mm (in.) | *b | Distance B mm (in.) |
Make sure that when the B measurement and selected No. 2 brake flange thickness are subtracted from the A measurement, the value is 2.20 to 2.50 mm (0.0866 to 0.0984 in.).
| Mark | Thickness |
|---|---|
| 0 | 1.95 to 2.05 mm (0.0768 to 0.0807 in.) |
| 1 | 2.05 to 2.15 mm (0.0807 to 0.0846 in.) |
| 2 | 2.15 to 2.25 mm (0.0846 to 0.0886 in.) |
| 3 | 2.25 to 2.35 mm (0.0886 to 0.0925 in.) |
| 4 | 2.35 to 2.45 mm (0.0925 to 0.0965 in.) |
| 5 | 2.45 to 2.55 mm (0.0965 to 0.100 in.) |
| 6 | 2.55 to 2.65 mm (0.100 to 0.104 in.) |
| 7 | 2.65 to 2.75 mm (0.104 to 0.108 in.) |
Remove the snap ring, flange and No. 2 brake piston return spring from the transmission case.
35682A
16.INSTALL NO. 2 BRAKE DISC SET
Install the No. 2 brake piston return spring, selected No. 2 brake flange, 4 No. 2 brake discs, 3 plates and flange.
S/F - D - P - D - P - D - P - D - F
S/F = Selected flange
D = No. 2 brake disc
P = Plate
F = Flange
Before assembling new discs, soak them in ATF for at least 2 hours.
Place SST on the flange and compress the No. 2 brake piston return spring.
Using a screwdriver, install the snap ring to the transmission case.
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with protective tape before use.
35750
17.INSTALL CENTER PLANETARY GEAR ASSEMBLY
Install the center planetary sun gear and center planetary gear assembly to the transmission case.
| *1 | Return Spring Retainer |
Make sure to install the center planetary sun gear with the groove facing the transmission case.
35621V
18.INSTALL NO. 1 BRAKE PISTON
Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.
| *1 | New O-Ring |
Press the No. 1 brake piston into the No. 1 brake cylinder with both hands.
Be careful not to damage the O-rings.
35698
19.INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
Install the No. 1 brake cylinder with No. 1 brake piston and brake piston return spring to the transmission case.
When installing the No. 1 brake cylinder with No. 1 brake piston to the transmission case, align the cylinder claw with the groove in the top of the case
Make sure the No. 1 brake cylinder with No. 1 brake piston is securely inserted into the transmission case.
Place SST on the brake piston return spring and compress the brake piston return spring.
Using a screwdriver, install the snap ring to the transmission case.
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with protective tape before use.
35676B
20.SELECT NO. 1 BRAKE FLANGE
Measure distance A (from the step in the transmission case to the tip of the No. 1 brake piston) in the illustration.*1
Standard distance A: 19.74 to 20.22 mm (0.777 to 0.796 in.)
Assemble the 4 plates and 4 discs and measure distance B in the illustration.*2
Standard distance B: 16.72 to 17.19 mm (0.658 to 0.677 in.)
| *1 | Disc |
| *2 | Plate |
Apply the A and B measurements taken in *1 and *2 to the graph below. Use A for the X axis and B for the Y axis, and then choose the No. 1 brake flange indicated by the graph point.
| *1 | Mark 0 | *2 | Mark 1 |
| *3 | Mark 2 | *4 | Mark 3 |
| *a | Distance A mm (in.) | *b | Distance B mm (in.) |
Make sure that when the B measurement and selected flange thickness are subtracted from the A measurement, the value is 0.56 to 0.86 mm (0.0220 to 0.0339 in.).
| Mark | Thickness |
|---|---|
| 0 | 1.95 to 2.05 mm (0.0768 to 0.0807 in.) |
| 1 | 2.15 to 2.25 mm (0.0846 to 0.0886 in.) |
| 2 | 2.35 to 2.45 mm (0.0925 to 0.0965 in.) |
| 3 | 2.55 to 2.65 mm (0.100 to 0.104 in.) |
35763
21.INSTALL CENTER PLANETARY RING GEAR
Install the front planetary ring gear flange to the center planetary ring gear.
Using a screwdriver, install the snap ring.
35743
22.INSTALL FRONT PLANETARY RING GEAR
Install the front planetary ring gear to the center planetary ring gear.
35743
23.INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR
Install the thrust bearing race and thrust needle roller bearing.
| *1 | Bearing |
| *2 | Race |
Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Race | 62.85 to 63.1 mm (2.47 to 2.48 in.) | 82.3 to 82.6 mm (3.24 to 3.25 in.) |
| Bearing | 65.35 to 65.6 mm (2.57 to 2.58 in.) | 85.6 to 85.95 mm (3.37 to 3.38 in.) |
Install the front planetary ring gear with the front planetary ring gear flange and center planetary ring gear to the transmission case.
35720
24.INSTALL FRONT PLANETARY GEAR ASSEMBLY
Install the No. 2 planetary carrier thrust washer to the front planetary gear assembly.
Use a small amount of MP grease to make the No. 2 planetary carrier thrust washer stay securely in place.
Install the thrust needle roller bearing, thrust bearing race, front planetary sun gear and front planetary gear assembly.
Use a small amount of MP grease to make the thrust needle roller bearing and thrust bearing race stay securely in place.
| *1 | Bearing |
| *2 | Race |
| Item | Inside | Outside |
|---|---|---|
| Bearing | 54.55 to 54.8 mm (2.15 to 2.16 in.) | 70.0 to 70.5 mm (2.76 to 2.78 in.) |
| Race | 55.0 to 55.2 mm (2.165 to 2.173 in.) | 68.8 to 69.3 mm (2.71 to 2.73 in.) |
35707C
25.INSTALL 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY
Install the No. 1 planetary carrier thrust washer to the 1-way clutch inner race, and then install them to the 1-way clutch assembly.
Use a small amount of MP grease to make the No. 1 planetary carrier thrust washer stay securely in place.
35790
26.INSPECT 1-WAY CLUTCH ASSEMBLY
35790
27.INSTALL 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY
Install the 1-way clutch assembly with the 1-way clutch inner race to the transmission case.
35681A
28.INSTALL NO. 1 BRAKE DISC SET
Install the 4 plates, 4 discs and No. 1 brake flange.
P - D - P - D - P - D - P - D - F
P = Plate
D = Disc
F = No. 1 brake flange
Before assembling new discs, soak them in ATF for at least 2 hours.
35624
29.INSTALL NO. 3 BRAKE PISTON
| *1 | New O-Ring |
Coat 2 new O-rings with ATF and install them to the No. 3 brake piston.
Press the No. 3 brake piston into the No. 3 brake cylinder with both hands.
Be careful not to damage the O-rings.
Using SST and a press, compress the No. 3 brake piston return spring and install the snap ring with a screwdriver.
Be sure the end gap of the snap ring is not aligned with the No. 3 brake piston return spring claw.
35664
30.INSTALL NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Install the No. 3 brake cylinder together with the No. 3 brake piston and No. 3 brake piston return spring to the transmission case.
Align the oil holes of the No. 3 brake cylinder and transmission case as shown in the illustration.
Make sure the No. 3 brake piston and cylinder are securely inserted into the transmission case.
| *1 | Oil Hole |
35624J
31.INSTALL NO. 3 BRAKE PISTON HOLE SNAP RING
Using SST, install the snap ring.
35066
32.INSTALL NO. 3 BRAKE DISC SET
Install the ''O'' mark flange, 4 discs, 3 plates and ''A'' mark flange to the transmission case.
OF - D - P - D - P - D - P - D - AF
OF = ''O'' mark flange
P = Plate
D = Disc
AF = ''A'' mark flange
Before assembling new discs, soak them in ATF for at least 2 hours.
35679C
33.INSTALL NO. 3 BRAKE SNAP RING
Using a screwdriver, install the snap ring.
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with protective tape before use.
35606A
34.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY
Coat 2 new O-rings with ATF and install them to the direct clutch piston.
| *1 | New O-ring |
Install the direct clutch return spring and No. 2 clutch balancer to the direct clutch piston.
Press the direct clutch piston together with the direct clutch return spring and No. 2 clutch balancer into the clutch drum with both hands.
Be careful not to damage the O-ring.
Place SST on the direct clutch balancer and compress the direct clutch return spring with a press.
Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
Set the end gap of the snap ring in the balancer as shown in the illustration.
| *1 | Stopper |
Be sure the end gap of the snap ring is not aligned with the spring retainer claw.
35667A
35.INSTALL DIRECT CLUTCH DISC SET
Place the oil pump assembly onto the torque converter, and then place the clutch drum onto the oil pump assembly.
for 1VD-FTV:
Install the 6 plates, 6 discs and direct clutch flange to the clutch drum.
P - D - P - D - P - D - P - D - P - D - P - D - F
P = Plate
D = Disc
F = Direct clutch flange
Before assembling new discs, soak them in ATF for at least 2 hours.
for 1UR-FE:
Install the 5 plates, 5 discs and direct clutch flange to the clutch drum.
P - D - P - D - P - D - P - D - P - D - F
P = Plate
D = Disc
F = Direct clutch flange
Before assembling new discs, soak them in ATF for at least 2 hours.
Using a screwdriver, install the snap ring to the clutch drum.
Be careful not to damage the clutch drum.
Wrap the tip of the screwdriver with protective tape before use.
Using a dial indicator, measure the moving distance (A) of the direct clutch flange at both ends across the diameter while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) into the oil hole as shown in the illustration. Then choose from the 9 flange thicknesses in the table so that the measured value is within the standard range.
0.58 to 0.88 mm (0.0228 to 0.0346 in.)
| *1 | Oil Hole |
| *a | Distance (A) |
| Mark | Thickness |
|---|---|
| 0 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 1 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 2 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| 3 | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| 4 | 3.85 to 3.95 mm (0.152 to 0.156 in.) |
| 5 | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
| 6 | 4.05 to 4.15 mm (0.159 to 0.163 in.) |
| 7 | 4.15 to 4.25 mm (0.163 to 0.167 in.) |
| 8 | 4.25 to 4.35 mm (0.167 to 0.171 in.) |
| A | 4.35 to 4.45 mm (0.171 to 0.175 in.) |
| Mark | Thickness |
|---|---|
| 0 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 1 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 2 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| 3 | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| 4 | 3.85 to 3.95 mm (0.152 to 0.156 in.) |
| 5 | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
| 6 | 4.05 to 4.15 mm (0.159 to 0.163 in.) |
| 7 | 4.15 to 4.25 mm (0.163 to 0.167 in.) |
| 8 | 4.25 to 4.35 mm (0.167 to 0.171 in.) |
Temporarily remove the snap ring, install the selected flange and reinstall the snap ring.
35048
36.INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY
| *1 | New O-Ring |
Coat a new O-ring with ATF and install it to the clutch drum.
Coat a new O-ring with ATF and install it to the reverse clutch piston.
| *1 | New O-Ring |
Insert the clutch drum into the reverse clutch piston with both hands.
Be careful not to damage the O-ring.
Make sure to align the holes of the reverse clutch piston with those of the clutch drum as shown in the illustration.
Make sure to align the protrusions of the reverse clutch piston with the cutout of the clutch drum.
35688
37.INSTALL NO. 3 CLUTCH BALANCER
| *1 | New O-ring |
Coat a new O-ring with ATF and install it to the reverse clutch piston.
Install the reverse clutch return spring and No. 3 balancer to the reverse clutch piston.
Place SST on the clutch balancer and compress the clutch balancer with a press.
Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
Set the end gap of the snap ring in the piston as shown in the illustration.
Be sure the end gap of the snap ring is not aligned with the spring retainer claw.
35649B
38.SELECT REVERSE CLUTCH FLANGE
Using a screwdriver, install the snap ring to the clutch drum.
| *1 | Protective Tape |
Be careful not to damage the clutch drum.
Make sure to install the direct clutch and reverse clutch snap rings so that their openings face opposite directions.
Wrap the tip of the screwdriver with protective tape before use.
for 1VD-FTV:
Install the flange, 4 discs, 3 plates, selected reverse clutch flange, cushion plate and reverse clutch reaction sleeve to the clutch drum.
F - D - P - D - P - D - P - D - S/F - C
F = Flange
D = Disc
P = Plate
S/F = Selected reverse clutch flange
C = Cushion plate
for 1UR-FE:
Install the flange, 5 discs, 4 plates, selected reverse clutch flange, cushion plate and reverse clutch reaction sleeve to the clutch drum.
F - D - P - D - P - D - P - D - P -D - S/F - C
F = Flange
D = Disc
P = Plate
S/F = Selected reverse clutch flange
C = Cushion plate
Using a screwdriver, install the snap ring.
Using a dial indicator, measure the moving distance (A minus B) of the top surface of the reverse clutch piston (A) and cushion plate (B) at both ends across the diameter while blowing compressed air (392 kPa, 2.0 kgf/cm2, 57 psi) into the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard range.
0.46 to 0.76 mm (0.0181 to 0.0299 in.)
0.59 to 0.89 mm (0.0232 to 0.0350 in.)
| *1 | Oil Hole | - | - |
| *a | Distance (A) | *b | Distance (B) |
| Mark | Thickness |
|---|---|
| 0 | 2.35 to 2.45 mm (0.0925 to 0.0965 in.) |
| 1 | 2.45 to 2.55 mm (0.0965 to 0.100 in.) |
| 2 | 2.55 to 2.65 mm (0.100 to 0.104 in.) |
| 3 | 2.65 to 2.75 mm (0.104 to 0.108 in.) |
| 4 | 2.75 to 2.85 mm (0.108 to 0.112 in.) |
| 5 | 2.85 to 2.95 mm (0.112 to 0.116 in.) |
| 6 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 7 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 8 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| A | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| B | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| C | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
Remove the snap ring, reverse clutch reaction sleeve and rear clutch disc set from the clutch drum.
35602A
39.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY
| *1 | New O-Ring |
Coat a new O-ring with ATF and install it to the input shaft.
Install the forward clutch piston to the input shaft.
35621V
40.INSTALL COAST CLUTCH PISTON
Install the coast clutch piston to the input shaft.
Coat a new O-ring with ATF and install it to the No. 1 clutch balancer.
| *1 | New O-Ring |
Install the forward clutch return spring and No. 1 clutch balancer to the input shaft.
Be careful not to damage the O-rings.
Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.
Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.
Using SST, install the snap ring.
Do not expand the snap ring excessively.
Set the end gap of the snap ring in the balancer as shown in the illustration.
Be sure the end gap of the snap ring is not aligned with the spring retainer claw.
| *a | Correct |
| *b | Incorrect |
35685
41.INSTALL COAST CLUTCH DISC SET
for 1VD-FTV:
Install the 5 plates, 5 discs and coast clutch flange.
P - D - P - D - P - D - P - D - P - D - F
P = Plate
D = Disc
F = Flange
Before assembling new discs, soak them in ATF for at least 2 hours.
for 1UR-FE:
Install the 4 plates, 4 discs and coast clutch flange.
P - D - P - D - P - D - P - D - F
P = Plate
D = Disc
F = Flange
Before assembling new discs, soak them in ATF for at least 2 hours.
Temporarily install the snap ring.
| *1 | Protective Tape |
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with protective tape before use.
Using a dial indicator, measure the moving distance (A) of the coast clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration. Then choose from the 11 flange thicknesses in the table so that the measured value is within the standard range.
0.51 to 0.81 mm (0.0201 to 0.0319 in.)
0.41 to 0.71 mm (0.0161 to 0.0280 in.)
| *1 | Oil Hole |
| *a | Distance (A) |
| Mark | Thickness |
|---|---|
| 0 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 1 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 2 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| 3 | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| 4 | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| 5 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 6 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 7 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| 8 | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| A | 3.85 to 3.95 mm (0.152 to 0.156 in.) |
| B | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
Temporarily remove the snap ring, install the selected coast clutch flange and reinstall the snap ring.
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with protective tape before use.
35633B
42.INSTALL FORWARD MULTIPLE DISC CLUTCH DISC SET
Install the cushion plate, 6 plates, 6 discs and flange to the input shaft.
C - P - D - P - D - P - D - P - D - P - D - P - D - F
C = Cushion plate
P = Plate
D = Disc
F = Flange
Before assembling new discs, soak them in ATF for at least 2 hours.
Temporarily install the snap ring.
| *1 | Protective Tape |
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with protective tape before use.
Using a dial indicator, measure the moving distance (A) of the clutch flange at both ends across the diameter while blowing compressed air (196 kPa, 2.0 kgf/cm2, 28 psi) into the oil hole as shown in the illustration. Then choose from the 12 flange thicknesses in the table so that the measured value is within the standard range.
0.85 to 1.15 mm (0.0335 to 0.0453 in.)
| *1 | Oil Hole |
| *a | Distance (A) |
| Mark | Thickness |
|---|---|
| 0 | 2.95 to 3.05 mm (0.116 to 0.120 in.) |
| 1 | 3.05 to 3.15 mm (0.120 to 0.124 in.) |
| 2 | 3.15 to 3.25 mm (0.124 to 0.128 in.) |
| 3 | 3.25 to 3.35 mm (0.128 to 0.132 in.) |
| 4 | 3.35 to 3.45 mm (0.132 to 0.136 in.) |
| 5 | 3.45 to 3.55 mm (0.136 to 0.140 in.) |
| 6 | 3.55 to 3.65 mm (0.140 to 0.144 in.) |
| 7 | 3.65 to 3.75 mm (0.144 to 0.148 in.) |
| 8 | 3.75 to 3.85 mm (0.148 to 0.152 in.) |
| A | 3.85 to 3.95 mm (0.152 to 0.156 in.) |
| B | 3.95 to 4.05 mm (0.156 to 0.159 in.) |
| C | 4.05 to 4.15 mm (0.159 to 0.163 in.) |
Temporarily remove the snap ring, install the selected flange and reinstall the snap ring.
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with protective tape before use.
35790H
43.INSTALL NO. 4 1-WAY CLUTCH ASSEMBLY
Install the No. 2 clutch hub thrust washer to the coast clutch hub.
Use a small amount of MP grease to make the No. 2 clutch hub thrust washer stay securely in place.
Install the No. 4 1-way clutch assembly to the coast clutch hub.
35790H
44.INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY
35064
45.INSTALL COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY
Install the 2 thrust needle roller bearings, thrust bearing race and coast clutch hub with the No. 4 1-way clutch assembly to the input shaft.
| *1 | Bearing C |
| *2 | Race |
| *3 | Bearing D |
Use a small amount of MP grease to make the thrust needle roller bearings and thrust bearing race stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Bearing C | 21.05 to 21.3 mm (0.829 to 0.839 in.) | 39.63 to 39.88 mm (1.56 to 1.57 in.) |
| Race | 22.8 to 23.1 mm (0.898 to 0.909 in.) | 44.5 to 44.75 mm (1.75 to 1.76 in.) |
| Bearing D | 39.45 to 39.7 mm (1.55 to 1.56 in.) | 60.5 to 60.75 mm (2.38 to 2.39 in.) |
35712A
46.INSTALL INPUT SHAFT OIL SEAL RING
Overlap the seal ring edges in the axial direction.
| *a | Correct |
| *b | Incorrect |
Overlapping the seal ring edges in the axial direction prevents damage to the seal ring.
Do not overlap the seal ring edges in the radial direction, as this may damage the seal ring.
Coat 4 new oil seal rings with ATF.
| *1 | New O-Ring |
Squeeze the ends of the 4 oil seal rings together, and then install them to the input shaft groove.
Do not excessively widen the rings.
After installing the oil seal rings, check that they rotate smoothly.
35701
47.INSTALL INPUT SHAFT ASSEMBLY
Install the input shaft to the clutch drum.
35061
48.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY
Install the No. 3 clutch hub thrust washer, forward clutch hub and thrust needle roller bearing to the clutch drum.
Before installing the forward clutch hub, apply ATF to the sliding surfaces of the forward clutch hub bush. After the installation, check that the forward clutch hub rotates smoothly.
Use a small amount of MP grease to make the thrust needle roller bearing and No. 3 clutch hub thrust washer stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Bearing | 46.45 to 46.7 mm (1.83 to 1.84 in.) | 64.3 to 64.55 mm (2.53 to 2.54 in.) |
35049
49.INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY
Install the reverse clutch hub to the clutch drum.
Before installing of the reverse clutch hub, apply ATF to the sliding surfaces of the reverse clutch hub bush. After the installation, check that the reverse clutch rotates smoothly.
35677C
50.INSTALL REAR CLUTCH DISC SET
Using a screwdriver, install the snap ring.
Be careful not to damage the clutch drum.
Wrap the tip of the screwdriver with protective tape before use.
for 1VD-FTV:
Install the flange, 4 discs, 3 plates, selected reverse clutch flange and reverse clutch reaction sleeve to the clutch drum.
F - D - P - D - P - D - P - D - S/F - C
F = Flange
D = Disc
P = Plate
S/F = Selected reverse clutch flange
C = Cushion plate
for 1UR-FE:
Install the flange, 5 discs, 4 plates, selected reverse clutch flange and reverse clutch reaction sleeve to the clutch drum.
F - D - P - D - P - D - P - D - P - D - S/F - C
F = Flange
D = Disc
P = Plate
S/F = Selected reverse clutch flange
C = Cushion plate
Using a screwdriver, install the snap ring to the clutch drum.
35780B
51.INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY
Install the clutch drum thrust washer to the clutch drum.
Use a small amount of MP grease to make the clutch drum thrust washer stay securely in place.
Install the 1-way clutch to the clutch drum.
35780B
52.INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY
53.INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
| *1 | Bearing A |
| *2 | Bearing B |
Install the 2 thrust needle roller bearings.
Use a small amount of MP grease to make the thrust needle roller bearings stay securely in place.
| Item | Inside | Outside |
|---|---|---|
| Bearing A | 71.96 to 72.26 mm (2.83 to 2.84 in.) | 85.25 to 85.6 mm (3.36 to 3.37 in.) |
| Bearing B | 36.45 to 36.7 mm (1.44 to 1.45 in.) | 52.96 to 53.26 mm (2.09 to 2.10 in.) |
Coat the clutch drum thrust washer with petroleum jelly and install it to the clutch drum and input shaft assembly.
Install the clutch drum and input shaft assembly to the transmission case.
54.INSTALL OIL PUMP ASSEMBLY
| *1 | Race A |
| *2 | Race B |
| *3 | New O-Ring |
Coat a new O-ring with ATF and install it to the oil pump assembly.
Install the 2 thrust bearing races to the front oil pump assembly.
| Item | Inside | Outside |
|---|---|---|
| Race A | 74.26 to 74.56 mm (2.92 to 2.94 in.) | 87.39 to 87.74 mm (3.44 to 3.45 in.) |
| Race B | 38.0 to 38.3 mm (1.50 to 1.51 in.) | 53.9 to 54.1 mm (2.12 to 2.13 in.) |
Pass the input shaft through the center hole of the oil pump assembly, and align the bolt holes of the oil pump assembly with the transmission case.
Hold the input shaft and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.
Apply seal packing to the flanges of the bolts.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Do not allow seal packing to contact the bolt threads.
Install the 10 bolts.
During installation, do not allow oil to contact the bolts or the surface of the oil pump body.
55.INSPECT INDIVIDUAL PISTON OPERATION
35506F
56.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL
Using SST, tap in 2 new oil seals.
Coat the lips of the oil seals with MP grease.
35505
57.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY
| *1 | New Spacer |
Install a new spacer to the manual valve lever sub-assembly.
Push the manual valve lever shaft through the transmission case and install the manual valve lever sub-assembly to the manual valve lever shaft.
Using a hammer, tap in a new spring pin.
Align the manual valve lever indentation with the spacer hole and stake them together with a punch.
Check that the shaft rotates smoothly.
35557
58.INSTALL PARKING LOCK PAWL
Install a new E-ring to the shaft.
Install the parking lock pawl, shaft and spring.
35501
59.INSTALL PARKING LOCK ROD SUB-ASSEMBLY
Connect the parking lock rod to the manual valve lever sub-assembly.
35595
60.INSTALL PARKING LOCK PAWL BRACKET
Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.
Move the manual valve lever sub-assembly to the P position and confirm that the planetary ring gear is correctly locked by the lock pawl.
| *1 | Lock Pawl |
| *2 | Rear Planetary Gear |
35424F
61.INSTALL B-1 ACCUMULATOR VALVE
Install the 2 springs and accumulator valve to the hole.
| Spring | Free Length
Outer Diameter |
Color |
|---|---|---|
| B-1 Inner | 44.98 mm (1.77 in.)
11.30 mm (0.445 in.) |
Natural |
| B-1 Outer | 46.36 mm (1.83 in.)
17.10 mm (0.673 in.) |
Natural |
35426D
62.INSTALL C-3 ACCUMULATOR PISTON
| *1 | New O-Ring |
Coat 2 new O-rings with ATF and install them to the piston.
Install the spring and accumulator piston to the hole.
| Spring | Free Length
Outer Diameter |
Color |
|---|---|---|
| C-3 | 76.65 mm (3.02 in.)
20.1 mm (0.791 in.) |
for 1VD-FTV:
White |
| for 1UR-FE:
Natural |
35427K
63.INSTALL B-3 ACCUMULATOR PISTON
| *1 | New O-Ring |
Coat 2 new O-rings with ATF and install them to the piston.
Install the spring and accumulator piston to the hole.
| Spring | Free Length
Outer Diameter |
Color |
|---|---|---|
| B-3 | 64.50 mm (2.54 in.)
19.5 mm (0.768 in.) |
Orange |
35425A
64.INSTALL C-2 ACCUMULATOR PISTON
| *1 | New O-Ring |
Coat 2 new O-rings with ATF and install them to the piston.
Install the spring and accumulator piston to the hole.
| Spring | Free Length
Outer Diameter |
Color |
|---|---|---|
| C-2 | 68.0 mm (2.68 in.)
16.1 mm (0.634 in.) |
for 1VD-FTV:
Blue |
| for 1UR-FE:
Light green |
35251
65.INSTALL CHECK BALL BODY
Install the spring and check ball body.
35159
66.INSTALL BRAKE DRUM GASKET
| *1 | New O-Ring |
Install 3 new brake drum gaskets.
35145C
67.INSTALL TRANSMISSION CASE GASKET
| *1 | New O-Ring |
Install 3 new transmission case gaskets.
35410
68.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
| *1 | Pin |
Align the hole of the manual valve with the pin of the lever.
Install the 19 bolts.
Each bolt length is indicated below.
36 mm (1.42 in.) for bolt A
25 mm (0.984 in.) for bolt B
45 mm (1.77 in.) for bolt C
50 mm (1.97 in.) for bolt D
Install the detent spring and detent spring cover with the bolt.
82125K
69.INSTALL NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE
| *1 | New O-Ring |
Install 2 new O-rings to the transmission wires.
Install the transmission wire harnesses.
Install the No. 1 transmission wire and No. 2 transmission wire with the 2 bolts.
Connect the 9 connectors to the solenoid valves.
| *a | Orange |
| *b | Blue |
Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.
Each bolt length is indicated below.
12 mm (0.472 in.) for bolt A
36 mm (1.42 in.) for bolt B
35330
70.INSTALL VALVE BODY OIL STRAINER ASSEMBLY
Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.
Install the valve body oil strainer assembly with the 4 bolts.
35106
71.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
| *1 | Magnet |
Install the 4 magnets.
Install a new gasket to the oil pan.
Install the oil pan with the 12 bolts.
Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.
Install the gasket so that there is no slack in the gasket, and make sure the entire circumference of the seal surface is level.
Make sure that the 9 gasket drop prevention protrusions are attached to the oil pan.
When tightening the bolts of the oil pan, make sure that the gasket is not pinched between the gasket tightening area sleeve and the transmission seal surface.
| *1 | Sleeve |
| *2 | Protrusion |
| *a | Correct |
| *b | Incorrect |
Install the drain plug.
35015E
72.INSTALL TRANSFER CASE ADAPTER RADIAL BALL BEARING
Using SST and a press, press in the bearing until it stops.
Using a screwdriver, install the snap ring.
35015J
73.INSTALL TRANSMISSION CASE ADAPTER OIL SEAL
| *a | 0 to 1 mm |
Coat the lip of a new oil seal with ATF.
Using SST and a hammer, tap in the oil seal.
0 to 1 mm (0 to 0.0394 in.)
35015G
74.INSTALL REAR TRANSFER ADAPTER
| *1 | Seal Packing |
| *a | Seal Diameter: 1 to 1.5 mm |
Clean the threads of the bolts and case with non-residue solvent.
Apply seal packing to the rear transfer adapter.
Toyota Genuine Seal Packing 1281,
Three Bond 1281 or equivalent
1.0 to 1.5 mm (0.0394 to 0.0591 in.)
Install the rear transfer adapter with the 10 bolts.
35111
75.INSTALL AUTOMATIC TRANSMISSION HOUSING
Clean the threads of the bolts and case with non-residue solvent.
Install the transmission housing with the 14 bolts.
35122
76.INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE
Coat a new O-ring with ATF and install it to the breather tube.
Install the breather tube with the 2 bolts.
33490F
77.INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)
32921C
78.INSTALL OIL COOLER TUBE UNION (w/o ATF Warmer)
Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.
Using a union nut wrench, install the 2 oil cooler tube unions.
| *a | -2 to 2° |
Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
89413B
79.INSTALL SPEED SENSOR
Coat 2 new O-rings with ATF and install them to the speed sensors.
Install the 2 speed sensors.
Install the 2 bolts.
84540
80.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.
Clean the bolt and the bolt hole.
Apply adhesive to 2 or 3 threads on the end of the bolt.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Temporarily install the park/neutral position switch assembly to the automatic transmission case subassembly with the bolt.
Install the lock washer and the nut to the park/ neutral position switch assembly.
Temporarily install the transmission control shaft lever RH.
Using the transmission control shaft lever RH, turn the manual lever shaft all the way back and then forward 2 notches to select the N position.
Remove the control shaft lever RH.
Align the groove with the neutral basic line.
| *1 | Neutral Basic Line |
| *2 | Groove |
Hold the switch in position and tighten the bolt.
Using a screwdriver, bend the tabs of the lock washer.
35572
81.INSTALL TRANSMISSION CONTROL SHAFT LEVER RH
Install the transmission control shaft lever RH with the washer and nut.