Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) U

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  DATA LIST / ACTIVE TEST  


READ DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -
Engine Speed Engine speed/
Min.: 0 rpm
Max.: 16383.75 rpm
Idling: 550 to 650 rpm -
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F)
Max.: 140°C (284°F)
After warming up engine: 75 to 90°C (167 to 194°F) If the value is -40°C (-40°F), the sensor circuit is open.
If the value is 140°C (284°F), the sensor circuit is shorted.
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever:
·

In P or N: ON

·

Not in P or N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Transfer L4 Transfer status/
ON or OFF
·

ON: Transfer in L4

·

OFF: Transfer not in L4


-
Stop Light Switch Stop light switch status/
ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
Lock-up:
·

ON (after warming up engine): Input turbine speed (NT) equal to engine speed

·

OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed


The data is displayed in increments of 50 rpm.
SPD (SP2) Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed equal to vehicle speed) -
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever:
·

In P: ON

·

Not in P: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Pattern Switch (PWR/M) PWR mode*1 or SPORT mode*2 status/
ON or OFF
·

ON: PWR mode*1 or SPORT mode*2 on

·

OFF: PWR mode*1 or SPORT mode*2 off


-
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever:
·

In R: ON

·

Not in R: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever:
·

In N: ON

·

Not in N: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


Shift SW Status (N, P Range) Supported Status of PNP switch (N or P) supported/
Unsupp or Supp
- -
Shift SW Status (N, P Range) PNP switch status/
ON or OFF
Shift lever:
·

In N or P: ON

·

Not in N or P: OFF


-
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Snow Switch Status ECT 2nd switch (integration control and panel assembly*3, suspension control switch*4) status/
ON or OFF
·

ON: ECT 2nd switch on

·

OFF: ECT 2nd switch off


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever:
·

In D: ON

·

Not in D: OFF


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
HINT:

When failure still occurs even after adjusting these parts, refer to DTC P0705 (See page (Click here)).


A/T Oil Temperature 1 No. 1 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approximately 80°C (176°F)

·

With engine cold: Equal to ambient temperature


If the value is -40°C (-40°F) or 150°C (302°F), the No. 1 ATF temperature sensor circuit is open or shorted.
A/T Oil Temperature 2 No. 2 ATF temperature sensor value/
Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

After stall test: Approximately 80°C (176°F)

·

With engine cold: Equal to ambient temperature


If the value is -40°C (-40°F) or 150°C (302°F), the No. 2 ATF temperature sensor circuit is open or shorted.
ATF Thermal Degradation Estimate Estimated value of ATF thermal degradation/
Min.: 0
Max.: 65535
- If 50000 or more is displayed for the Data List item "ATF Thermal Degradation Estimate", thermal degradation of the ATF is suspected. Perform ATF Thermal Degradation Estimate Reset after replacing the ATF.
Normal Mode Switch NORM switch (integration control and panel assembly) status*2/
ON or OFF
·

ON: NORM switch on

·

OFF: NORM switch off


-
Sports Mode Switch PWR switch*1 (integration control and panel assembly*3, suspension control switch*4) or SPORT switch*2 (integration control and panel assembly) status/
ON or OFF
·

ON: PWR switch*1 or SPORT S/S+ switch*2 on

·

OFF: PWR switch*1 or SPORT S/S+ switch*2 off


-
Lock Up Lock-up/
ON or OFF
Lock-up:
·

Operating: ON

·

Not operating: OFF


-
Shift Status ECM gear shift command/
1st, 2nd, 3rd, 4th, 5th or 6th
Shift lever:
·

In D: 1st, 2nd, 3rd, 4th, 5th or 6th

·

In S: 1st, 2nd, 3rd, 4th, 5th or 6th


-
SLT Solenoid Status Shift solenoid valve SLT status/
ON or OFF
·

Accelerator pedal depressed: OFF

·

Accelerator pedal released: ON


-
SLU Solenoid Status Shift solenoid valve SLU status/
ON or OFF
Shift solenoid valve SLU:
·

Operating: ON

·

Not operating: OFF


-
Snow or 2nd Start Mode 2nd Start mode status/
ON or OFF
·

ON: 2nd Start mode on

·

OFF: 2nd Start mode off


-

*1: w/o Active Height Control Suspension

*2: w/ Active Height Control Suspension

*3: w/ Entry and Start System

*4: w/o Entry and Start System



PERFORM ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Connect the TC and TE1 Turn on and off TC and TE1 connection ON or OFF
·

ON: TC and TE1 are connected.

·

OFF: TC and TE1 are disconnected.


Activate the Solenoid (SLU) Operate shift solenoid valve SLU ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (SLT)* Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT solenoid to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

The vehicle is stopped.

·

The engine is idling.


Activate the Solenoid (S1) Operate shift solenoid valve S1 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (S2) Operate shift solenoid valve S2 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (S3) Operate shift solenoid valve S3 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (S4) Operate shift solenoid valve S4 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Lock Up Control shift solenoid valve SLU to set automatic transmission to lock-up condition ON or OFF It is possible to check the shift solenoid valve SLU operation.
[Vehicle Condition]
·

Vehicle speed: 70 km/h (44 mph) or more

·

Gear: Highest gear

·

Throttle valve opening angle: 20% or more


Control the Shift Position Operate shift solenoid valve and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.
Activate the Solenoid (SR) Operate shift solenoid valve SR ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (SL1) Operate shift solenoid valve SL1 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.


Activate the Solenoid (SL2) Operate shift solenoid valve SL2 ON or OFF [Vehicle Condition]
·

Ignition switch ON

·

The engine is stopped.

·

The shift lever is in P or N.



HINT:

*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.