Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 The transfer L4 position switch remains on while the vehicle is running under the following conditions for 1.8 sec. or more (1 trip detection logic).
(a) The output shaft speed is between 1000 and 3000 rpm.
(b) The transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

Four wheel drive control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the transfer-case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

L4 switch indicated that the L4 transfer-case gears are engaged.

·

The transfer-case shifter is in the "H4" position.

·

The transfer-case output shaft rpm is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C179559E02
5.19,0.929 5.420,1.099 0.230,0.170 10 21 5.512,0.837 5.934,1.032 0.422,0.195 10 L4 1.853,0.929 2.083,1.099 0.230,0.170 10 21 1.51,0.837 1.752,1.032 0.242,0.195 10 L4 1.853,1.603 2.083,1.773 0.230,0.170 10 16 1.51,1.494 1.747,1.689 0.237,0.195 10 NP 1.766,3.19 1.908,3.360 0.142,0.170 10 3 1.541,3.081 1.722,3.276 0.181,0.195 10 N 5.197,3.19 5.427,3.360 0.230,0.170 10 39 5.512,3.081 5.934,3.276 0.422,0.195 10 TFN 0.379,3.7 2.470,3.895 2.091,0.195 10 Transfer Shift Actuator Assembly 0.379,3.519 0.801,3.715 0.422,0.195 10 C38 0.379,2.323 2.354,2.518 1.974,0.195 10 Four Wheel Drive Control ECU 0.379,2.142 0.801,2.338 0.422,0.195 10 A27 5.689,4.179 6.070,4.374 0.382,0.196 10 ECM 5.689,3.805 6.132,4.006 0.443,0.202 10 A38*1 5.689,3.991 6.132,4.193 0.443,0.202 10 A52*2 0.047,4.09 0.842,4.265 0.795,0.174 10 *1: for LHD 0.047,4.436 0.842,4.610 0.795,0.174 10 *2: for RHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U164575E01
0.055,0.002 2.463,0.370 2.408,0.367 10 Front view of wire harness connector: (to Four Wheel Drive Control ECU) 1.579,1.132 1.954,1.365 0.375,0.233 10 A27 0.18,2.814 0.438,3.016 0.258,0.202 10 L4 0.316,2.799 0.535,2.158 false

Disconnect the four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-21 (L4) - Body ground Always 10 kΩ or higher




OK

GO TO TRANSFER SYSTEM INSPECTION

NG

2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
a.
U164899E01
0.054,3.776 0.848,3.951 0.795,0.174 10 *1: for LHD 0.054,4.2 0.848,4.375 0.795,0.174 10 *2: for RHD 1.668,1.377 2.043,1.610 0.375,0.233 10 A52 1.668,1.068 2.043,1.301 0.375,0.233 10 A38 2.077,1.377 2.278,1.579 0.200,0.202 10 *2 2.077,1.068 2.278,1.269 0.200,0.202 10 *1 0.051,0.007 2.459,0.374 2.408,0.367 10 Front view of wire harness connector: (to ECM) 0.97,3.23 1.497,3.432 0.527,0.202 10 21 (L4) 1.28,3.215 1.589,2.161 false

Disconnect the ECM connector.


b.

Disconnect the A27 four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-21 (L4) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-21 (L4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR