Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › 2014.08–2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM G

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT INDICATOR LIGHT

a.

Check the 4LO indicator light.

i.

Start the engine.


ii.

Stop the vehicle.


iii.

for Automatic Transmission: Move the shift lever to N.

for Manual Transmission: Depress the clutch pedal.


iv.

Turn the transfer position switch from H4 to L4.


v.

Check the 4LO indicator light.

·
C172438E01
0.061,0 0.847,0.276 0.786,0.276 12 w/ VSC:

w/ VSC:

OK:
Switch Condition Specified Condition
Turned from H4 to L4 4LO indicator light comes on immediately or comes on after blinking


If there is a malfunction, inspect the switch, ECU and transfer shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In that case, first check the CAN communication system for LHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>PRECAUTION), for RHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>PRECAUTION). Then check the combination meter (See page ).

·
C175624E01
0.108,0.031 0.898,0.261 0.790,0.230 12 w/o VSC: 1.294,1.478 2.922,1.710 1.628,0.232 10 4LO Indicator Light 1.294,2.28 2.996,2.705 1.702,0.424 10 Center Differential Lock Indicator Light

w/o VSC:

OK:
Switch Condition Specified Condition
Turned from H4 to L4 4LO indicator light and center differential lock indicator light come on immediately or come on after blinking


If there is a malfunction, inspect the switch, ECU and transfer shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In that case, first check the CAN communication system for LHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>PRECAUTION), for RHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>PRECAUTION). Then check the combination meter (See page ).

HINT:

For vehicles without VSC (Vehicle Stability Control), when the transfer position switch is turned from H4 to L4, the center differential will lock.



Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



b.

Check the center differential lock indicator light.

i.

Start the engine.


ii.
C172440

Push the center differential lock switch.

NOTICE:
·

Do not push the switch while the vehicle is turning.

·

Push the switch at a vehicle speed less than 100 km/h (60 mph).




iii.

Check the center differential lock indicator light.

OK:
Switch Condition Specified Condition
Pushed Center differential lock indicator light comes on immediately or comes on after blinking


If there is a malfunction, inspect the switch, ECU and transfer shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In that case, first check the CAN communication system for LHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>PRECAUTION), for RHD (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>PRECAUTION). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



c.

w/ Rear Differential Lock:

Check the rear differential lock indicator light.

i.

Start the engine.


ii.

Stop the vehicle.


iii.

for Automatic Transmission: Move the shift lever to N.

for Manual Transmission: Depress the clutch pedal.


iv.

Turn the transfer position switch from H4 to L4.

HINT:

The rear differential can be locked only when the following conditions are met: 1) The transfer is in low, and 2) the center differential is locked. As vehicles with a rear differential lock do not have a vehicle stability control system, these conditions will be satisfied after the transfer position switch is turned to L4, the transfer shifts to low, and the center differential locks.



v.

Turn the differential lock switch from OFF to RR.

NOTICE:

When locking the rear differential, make sure that the vehicle speed is less than 8 km/h (5 mph).



vi.
C172439E01
0.08,0 2.208,0.231 2.128,0.231 12 w/ Rear Differential Lock:

Check the rear differential lock indicator light.

OK:
Switch Condition Specified Condition
After transfer position switch is turned from H4 to L4, differential lock switch is turned from OFF to RR Rear differential lock indicator light comes on immediately or comes on after blinking


If there is a malfunction, inspect the switch, ECU and differential lock shift actuator.

HINT:
·

The 4LO indicator light and center differential lock indicator light are both illuminated.

·

When the rear differential is locked, if the transfer position switch is returned to H4, the rear differential becomes free. However, since the differential lock switch is on RR, the rear differential lock indicator light blinks, and when the differential lock switch is turned to OFF, the indicator light turns off.





Hide 2.INSPECT FUSE

a.

Remove the 4WD fuse from the main body ECU (cowl side junction block LH).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4WD fuse Always Below 1 Ω


If a fuse is blown, inspect the harness connected to the fuse for a short circuit, and repair or replace the harness or replace the fuse.


Hide 84223A 3.INSPECT TRANSFER POSITION SWITCH

a.

Remove the transfer position switch (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>4WD CONTROL SWITCH>REMOVAL).


b.
C172468E03
2,2.302 2.698,2.823 false 1.5,2.313 0.854,2.792 false 0.281,0.073 2.781,0.448 2.5,0.375 10 false Component without harness connected: (Transfer Position Switch) 2.698,2.844 3.104,3.094 0.406,0.25 10 false 2WD 0.469,2.792 0.927,3.042 0.458,0.25 10 false GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (2WD) - 4 (GND2) H4 position 100 kΩ or higher
L4 position Below 1 Ω


If there is a malfunction, replace the transfer position switch.


c.

Check the harness and connector (ECU - transfer position switch and body ground).

i.

Disconnect the A27 ECU connector.


ii.

Disconnect the E48 transfer position switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164566E02
1.792,1.792 1.542,2.229 false 5.594,1.635 5.688,2.313 false 2.281,1.781 2.49,2.229 false 4.063,0.25 6.448,0.708 2.385,0.458 10 false Front view of wire harness connector: (to Four Wheel Drive Control ECU) 0.667,0.219 3.167,0.677 2.5,0.458 10 false Front view of wire harness connector: (to Transfer Position Switch) 1.396,2.292 1.792,2.49 0.396,0.198 10 false 2WD 5.625,2.313 5.875,2.51 0.25,0.198 10 false LO 3.615,1.552 3.948,1.74 0.333,0.188 10 false A27 1.063,1.51 1.396,1.698 0.333,0.188 10 false E48 2.344,2.292 2.792,2.5 0.448,0.208 10 false GND2

Standard Resistance:
Tester Connection Condition Specified Condition
E48-2 (2WD) - A27-13 (LO) Always Below 1 Ω
E48-2 (2WD) - Body ground Always 100 kΩ or higher
E48-4 (GND2) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



Hide 84725 4.INSPECT CENTER DIFFERENTIAL LOCK SWITCH

a.

Remove the center differential lock switch (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>CENTER DIFFERENTIAL LOCK SWITCH>REMOVAL).


b.
C261661E02
2.104,2.563 2.667,2.813 true 1.521,2.583 0.615,2.896 true 0.271,0.292 3.385,1.052 3.115,0.76 12 false Component without harness connected: (Center Differential Lock Switch) 2.719,2.813 2.854,2.958 0.135,0.146 10 false L 0.354,2.896 0.75,3.083 0.396,0.188 10 false CPU

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (L) - 4 (CPU) Switch is pressed and held Below 1 Ω
Switch is not pressed 100 kΩ or higher


If there is a malfunction, replace the center differential lock switch.


c.

Check the harness and connector (ECU - center differential lock switch and body ground).

i.

Disconnect the ECU connector.


ii.

Disconnect the center differential lock switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U165381E02
5.313,1.375 5.49,2 false 1.354,1.479 1.104,1.833 false 1.865,1.479 2.188,1.813 false 3.906,0.219 6.25,0.802 2.344,0.583 10 false Front view of wire harness connector: (to Four Wheel Drive Control ECU) 0.5,0.198 2.844,0.677 2.344,0.479 10 false Front view of wire harness connector: (to Center Differential Lock Switch) 3.344,1.333 3.677,1.531 0.333,0.198 10 false A27 5.49,2.031 5.74,2.208 0.25,0.177 10 false DL 1,1.833 1.156,2.01 0.156,0.177 10 false L 2.156,1.854 2.688,2.052 0.531,0.198 10 false CPU 0.781,1.24 1.115,1.438 0.333,0.198 10 false G12

Standard Resistance:
Tester Connection Condition Specified Condition
A27-12 (DL) - G12-4 (CPU) Always Below 1 Ω
A27-12 (DL) - Body ground Always 100 kΩ or higher
G12-1 (L) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



Hide 84725A 5.INSPECT DIFFERENTIAL LOCK SWITCH (w/ Rear Differential Lock)


b.
C175630E01
0.235,0.116 2.795,0.520 2.560,0.404 10 Component without harness connected: (Differential Lock Switch) 2.403,2.778 2.608,2.934 0.206,0.156 10 IG 1.174,2.778 1.357,2.941 0.184,0.163 10 R 1.449,2.159 1.277,2.692 false 2.423,2.171 2.448,2.717 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG) - 4 (R) OFF 10 kΩ or higher
RR Below 1 Ω


If there is a malfunction, replace the differential lock switch.


c.

Check the harness and connector (ECU - differential lock switch and body ground).

i.

Disconnect the A27 ECU connector.


ii.

Disconnect the E87 differential lock switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164827E02
5.344,1.625 5.521,2.25 false 1.26,1.823 1.01,2.146 false 1.813,1.833 2.083,2.198 false 4.094,0.281 6.573,0.74 2.479,0.458 10 false Front view of wire harness connector: (to Four Wheel Drive Control ECU) 0.698,0.25 3.198,0.708 2.5,0.458 10 false Front view of wire harness connector: (to Differential Lock Switch) 3.458,1.573 3.792,1.771 0.333,0.198 10 false A27 5.563,2.26 5.813,2.438 0.25,0.177 10 false R 0.5,1.594 0.771,1.74 0.271,0.146 10 false E87 0.906,2.177 1.115,2.375 0.208,0.198 10 false IG 2.115,2.188 2.271,2.365 0.156,0.177 10 false R

Standard Resistance:
Tester Connection Condition Specified Condition
A27-11 (R) - E87-1 (IG) Always Below 1 Ω
A27-11 (R) - Body ground Always 100 kΩ or higher
E87-4 (R) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



Hide 36410J 6.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (HIGH-LOW TRANSFER SHIFT ACTUATOR)

HINT:

After inspecting the ECU power supply or transfer position switch, check the high-low transfer shift actuator.


a.

Check the harness and connector (ECU - high-low transfer shift actuator).

i.

Disconnect the C38 actuator connector.


ii.

Disconnect the A27 and A28 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U164565E02
3.417,1.75 3.938,2.375 false 3.385,1.99 3.385,2.365 false 0.563,1.792 0.292,2.354 false 0.698,1.813 0.688,2.354 false 0.813,1.802 1.094,2.375 false 2.156,1.802 2.156,2.375 false 5.146,1.917 4.958,2.219 false 5.385,1.927 5.208,2.406 false 5.542,1.927 5.542,2.25 false 5.75,1.896 5.75,2.438 false 5.938,1.927 6.083,2.26 false 6.156,1.927 6.635,2.469 false 6.344,1.708 6.542,1.26 false 1.094,0.125 3.51,0.583 2.417,0.458 10 false Front view of wire harness connectors: (to Four Wheel Drive Control ECU) 4.573,0.104 6.938,0.615 2.365,0.51 10 false Front view of wire harness connector: (to High-low Transfer Shift Actuator) 1.438,1.167 1.771,1.365 0.333,0.198 10 false A27 3.51,1.125 3.844,1.323 0.333,0.198 10 false A28 5.656,1.052 5.99,1.25 0.333,0.198 10 false C38 3.969,2.406 4.323,2.604 0.354,0.198 10 false HM1 3.24,2.438 3.625,2.615 0.385,0.177 10 false HM2 0.135,2.406 0.49,2.563 0.354,0.156 10 false HL1 0.552,2.406 0.927,2.573 0.375,0.167 10 false HL2 2.073,2.417 2.302,2.573 0.229,0.156 10 false NP 6.01,2.313 6.313,2.479 0.302,0.167 10 false HL3 4.656,2.292 5.01,2.49 0.354,0.198 10 false HM1 5,2.479 5.385,2.656 0.385,0.177 10 false HM2 5.698,2.5 6.052,2.656 0.354,0.156 10 false HL1 6.604,2.51 6.979,2.677 0.375,0.167 10 false HL2 5.49,2.302 5.719,2.458 0.229,0.156 10 false N 1.063,2.406 1.365,2.573 0.302,0.167 10 false HL3 6.594,1.167 6.917,1.365 0.323,0.198 10 false GND

Standard Resistance:
Tester Connection Condition Specified Condition
A27-1 (HL1) - C38-4 (HL1) Always Below 1 Ω
A27-1 (HL1) - Body ground Always 100 kΩ or higher
A27-2 (HL2) - C38-6 (HL2) Always Below 1 Ω
A27-2 (HL2) - Body ground Always 100 kΩ or higher
A27-3 (HL3) - C38-5 (HL3) Always Below 1 Ω
A27-3 (HL3) - Body ground Always 100 kΩ or higher
A27-16 (NP) - C38-3 (N) Always Below 1 Ω
A27-16 (NP) - Body ground Always 100 kΩ or higher
A28-2 (HM1) - C38-1 (HM1) Always Below 1 Ω
A28-2 (HM1) - Body ground Always 100 kΩ or higher
A28-6 (HM2) - C38-2 (HM2) Always Below 1 Ω
A28-6 (HM2) - Body ground Always 100 kΩ or higher
C38-7 (GND) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



b.

Check the high-low transfer shift actuator.

i.

Turn the engine switch on (IG).


ii.

Stop the vehicle.


iii.

for Automatic Transmission: Move the shift lever to N.

for Manual Transmission: Depress the clutch pedal.


iv.

Check that there is an operating noise from the transfer shift actuator when the transfer position switch is turned from H4 to L4, or L4 to H4.

OK:

There is an operating noise.


HINT:
·

If the actuator fork cannot move from high to low, or low to high even though there is an operating noise, there may be a mechanical malfunction in the transfer.

·

If there is no operating noise, there may be a malfunction in the high-low transfer shift actuator. However, it may also be a result of a mechanical malfunction in the transfer, so inspect each part.




v.

Remove the transfer shift actuator assembly (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>REMOVAL).


vi.

Check the high to low switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the high to low position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179848E01
0.759,0.077 3.304,0.427 2.545,0.350 10 Component without harness connected: (High-low Transfer Shift Actuator) 2.23,3.741 2.603,3.900 0.373,0.159 10 HM1 1.873,4.078 2.217,4.248 0.343,0.170 10 HM2 1.255,4.061 1.563,4.231 0.309,0.170 10 HL1 1.638,4.115 1.839,4.278 0.200,0.163 10 N 0.243,3.824 0.622,3.987 0.378,0.163 10 GND 0.586,4.046 0.919,4.222 0.333,0.177 10 HL2 0.938,4.161 1.275,4.324 0.336,0.163 10 HL3 1.621,3.843 1.856,4.084 false 1.463,3.853 1.632,4.098 false 1.33,3.853 1.33,4.025 false 1.19,3.839 1.085,4.123 false 1.048,3.84 0.861,4.046 false 0.938,3.838 0.623,3.878 false 1.782,3.815 2.188,3.815 false 5.58,1.62 6.553,1.822 0.973,0.202 10 DEFOG Relay: 5.162,2.29 5.346,2.471 0.185,0.181 10 1 6.591,3.907 6.755,4.100 0.164,0.193 10 2 6.769,2.321 6.910,2.486 0.141,0.165 10 4 6.897,3.072 7.063,3.263 0.166,0.191 10 5 4.783,3.063 4.950,3.224 0.167,0.161 10 3 5.278,2.365 5.532,2.365 5.532,2.365 6.011,2.788 false 6.076,3.14 6.501,2.403 6.501,2.403 6.675,2.403 false 6.417,3.14 6.834,3.14 false 5.72,3.14 4.934,3.14 false 6.011,3.512 6.415,3.979 6.415,3.979 6.536,3.979 false 0.222,0.901 1.059,1.084 0.837,0.184 10 High → Low:

2.

After the high to low switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N) - 7 (GND) After high to low switch is complete 100 kΩ or higher
4 (HL1) - 7 (GND) After high to low switch is complete 100 kΩ or higher
5 (HL3) - 7 (GND) After high to low switch is complete 100 kΩ or higher
6 (HL2) - 7 (GND) After high to low switch is complete Below 1 Ω


If there is a malfunction, replace the transfer shift actuator assembly.




vii.

Check the low to high switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the low to high position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179849E01
0.759,0.156 3.304,0.507 2.545,0.350 10 Component without harness connected: (High-low Transfer Shift Actuator) 2.23,3.741 2.603,3.900 0.373,0.159 10 HM1 1.873,4.078 2.217,4.248 0.343,0.170 10 HM2 1.255,4.061 1.563,4.231 0.309,0.170 10 HL1 1.638,4.115 1.839,4.278 0.200,0.163 10 N 0.243,3.824 0.622,3.987 0.378,0.163 10 GND 0.586,4.046 0.919,4.222 0.333,0.177 10 HL2 0.938,4.161 1.275,4.324 0.336,0.163 10 HL3 1.621,3.843 1.856,4.084 false 1.463,3.853 1.632,4.098 false 1.33,3.853 1.33,4.025 false 1.19,3.839 1.085,4.123 false 1.048,3.84 0.861,4.046 false 0.938,3.838 0.623,3.878 false 1.782,3.815 2.188,3.815 false 5.568,1.717 6.541,1.920 0.973,0.202 10 DEFOG Relay: 5.149,2.286 5.334,2.468 0.185,0.181 10 1 6.579,3.903 6.743,4.096 0.164,0.193 10 2 6.757,2.318 6.898,2.483 0.141,0.165 10 4 6.825,3.069 6.991,3.260 0.166,0.191 10 5 4.771,3.06 4.938,3.221 0.167,0.161 10 3 5.266,2.361 5.52,2.361 5.52,2.361 5.999,2.784 false 6.084,3.137 6.509,2.4 6.509,2.4 6.683,2.4 false 6.417,3.137 6.774,3.137 false 5.708,3.137 4.922,3.137 false 5.999,3.509 6.403,3.976 6.403,3.976 6.524,3.976 false 0.157,0.999 1.058,1.183 0.902,0.184 10 High ← Low:

2.

After the low to high switch is complete, check the neutral position detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (N) - 7 (GND) After low to high switch is complete 100 kΩ or higher
4 (HL1) - 7 (GND) After low to high switch is complete Below 1 Ω
5 (HL3) - 7 (GND) After low to high switch is complete 100 kΩ or higher
6 (HL2) - 7 (GND) After low to high switch is complete 100 kΩ or higher


If there is a malfunction, replace the transfer shift actuator assembly.





Hide 36410J 7.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (CENTER DIFFERENTIAL LOCK ACTUATOR)

HINT:

After inspecting the ECU power supply or center differential lock switch, inspect the center differential lock actuator.


a.

Check the harness and connector (ECU - center differential lock actuator).

i.

Disconnect the C37 actuator connector.


ii.

Disconnect the A27 and A28 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U164564E02
1,1.792 0.604,2.313 false 1.229,1.781 1.573,2.333 false 1.844,1.781 2.115,2.344 false 3.417,1.938 3.344,2.281 false 3.677,1.938 3.854,2.292 false 5.042,1.917 4.823,2.302 false 5.26,1.927 5.146,2.521 false 5.448,1.927 5.448,2.281 false 5.688,1.917 5.865,2.51 false 5.865,1.917 6.167,2.51 false 6.208,1.927 6.625,2.104 false 1.125,1.771 1.125,2.323 false 6.021,1.917 6.406,2.302 false 1.104,0.115 3.677,0.573 2.573,0.458 10 false Front view of wire harness connectors: (to Four Wheel Drive Control ECU) 4.479,0.094 6.979,0.552 2.5,0.458 10 false Front view of wire harness connector: (to Center Differential Lock Actuator) 1.344,1.146 1.677,1.344 0.333,0.198 10 false A27 3.417,1.115 3.75,1.313 0.333,0.198 10 false A28 5.573,1.031 5.906,1.229 0.333,0.198 10 false C37 3.823,2.333 4.177,2.531 0.354,0.198 10 false TM1 3.177,2.344 3.563,2.521 0.385,0.177 10 false TM2 0.417,2.365 0.771,2.583 0.354,0.219 10 false TL1 1.479,2.365 1.854,2.531 0.375,0.167 10 false TL3 2.063,2.365 2.531,2.583 0.469,0.219 10 false P1 4.594,2.333 4.917,2.51 0.323,0.177 10 false TM1 4.969,2.552 5.281,2.719 0.313,0.167 10 false TM2 5.781,2.552 6.073,2.708 0.292,0.156 10 false TL1 6.167,2.552 6.458,2.719 0.292,0.167 10 false TL3 5.365,2.354 5.719,2.521 0.354,0.167 10 false CDL 6.708,2.052 7.156,2.24 0.448,0.188 10 false GND1 1.01,2.365 1.344,2.552 0.333,0.188 10 false TL2 6.448,2.323 6.854,2.531 0.406,0.208 10 false TL2

Standard Resistance:
Tester Connection Condition Specified Condition
A27-6 (TL1) - C37-4 (TL1) Always Below 1 Ω
A27-6 (TL1) - Body ground Always 100 kΩ or higher
A27-7 (TL2) - C37-6 (TL2) Always Below 1 Ω
A27-7 (TL2) - Body ground Always 100 kΩ or higher
A27-8 (TL3) - C37-5 (TL3) Always Below 1 Ω
A27-8 (TL3) - Body ground Always 100 kΩ or higher
A27-14 (P1) - C37-3 (CDL) Always Below 1 Ω
A27-14 (P1) - Body ground Always 100 kΩ or higher
A28-7 (TM2) - C37-2 (TM2) Always Below 1 Ω
A28-7 (TM2) - Body ground Always 100 kΩ or higher
A28-8 (TM1) - C37-1 (TM1) Always Below 1 Ω
A28-8 (TM1) - Body ground Always 100 kΩ or higher
C37-7 (GND) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



b.

Check the center differential lock actuator.

i.

Turn the engine switch on (IG).


ii.

Check that there is an operating noise from the transfer shift actuator when the center differential lock switch is pressed to switch from free to lock, or lock to free.

OK:

There is an operating noise.


HINT:
·

If the actuator fork cannot move from free to lock, or lock to free even though there is an operating noise, there may be a mechanical malfunction in the transfer.

·

If there is no operating noise, there may be a malfunction in the center differential lock actuator. However, it may also be a result of a mechanical malfunction in the transfer, so inspect each part.




iii.

Remove the transfer shift actuator assembly (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>REMOVAL).


iv.

Check the free to lock switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the free to lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179846E01
2.288,3.466 2.660,3.625 0.373,0.159 10 TM1 2.071,3.973 2.414,4.143 0.343,0.170 10 TM2 1.579,3.973 1.943,4.137 0.364,0.163 10 CDL 0.346,3.684 0.808,3.847 0.461,0.163 10 GND1 1.057,3.914 1.352,4.097 0.295,0.184 10 TL3 0.717,0.108 3.220,0.458 2.503,0.350 10 Component without harness connected: (Center Differential Lock Actuator) 1.846,3.548 2.248,3.548 false 1.695,3.571 2.056,3.935 false 1.273,3.575 1.178,3.898 false 1.024,3.583 0.794,3.684 false 1.547,3.598 1.697,3.934 false 0.59,3.987 0.885,4.170 0.295,0.184 10 TL2 1.309,4.127 1.604,4.310 0.295,0.184 10 TL1 1.416,3.58 1.416,4.093 false 1.16,3.589 0.795,3.953 false 5.518,1.696 6.491,1.898 0.973,0.202 10 DEFOG Relay: 5.1,2.265 5.284,2.446 0.185,0.181 10 1 6.529,3.882 6.693,4.075 0.164,0.193 10 2 6.707,2.297 6.848,2.462 0.141,0.165 10 4 6.832,3.048 6.997,3.238 0.166,0.191 10 5 4.721,3.039 4.888,3.199 0.167,0.161 10 3 5.216,2.34 5.47,2.34 5.47,2.34 5.949,2.763 false 6.034,3.115 6.459,2.379 6.459,2.379 6.633,2.379 false 6.368,3.115 6.773,3.115 false 5.658,3.115 4.872,3.115 false 5.949,3.488 6.353,3.955 6.353,3.955 6.474,3.955 false 0.219,0.974 1.177,1.158 0.957,0.184 10 Free → Lock:

2.

After the free to lock switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After free to lock switch is complete Below 1 Ω
4 (TL1) - 7 (GND1) After free to lock switch is complete 100 kΩ or higher
5 (TL3) - 7 (GND) After free to lock switch is complete 100 kΩ or higher
6 (TL2) - 7 (GND1) After free to lock switch is complete Below 1 Ω


If there is a malfunction, replace the transfer shift actuator assembly.




v.

Check the lock to free switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the lock to free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C179847E01
2.236,3.615 2.609,3.775 0.373,0.159 10 TM1 2.019,4.123 2.362,4.292 0.343,0.170 10 TM2 1.528,4.123 1.891,4.286 0.364,0.163 10 CDL 0.294,3.834 0.756,3.997 0.461,0.163 10 GND1 1.006,4.063 1.300,4.247 0.295,0.184 10 TL3 0.717,0.108 3.220,0.458 2.503,0.350 10 Component without harness connected: (Center Differential Lock Actuator) 1.794,3.698 2.196,3.698 false 1.643,3.72 2.004,4.084 false 1.221,3.724 1.127,4.047 false 0.973,3.732 0.743,3.834 false 1.495,3.748 1.645,4.084 false 0.539,4.136 0.833,4.320 0.295,0.184 10 TL2 1.258,4.276 1.553,4.460 0.295,0.184 10 TL1 1.365,3.729 1.365,4.243 false 1.108,3.738 0.744,4.103 false 5.524,1.699 6.497,1.902 0.973,0.202 10 DEFOG Relay: 5.105,2.268 5.290,2.450 0.185,0.181 10 1 6.535,3.885 6.699,4.078 0.164,0.193 10 2 6.713,2.3 6.854,2.465 0.141,0.165 10 4 6.725,3.051 6.891,3.242 0.166,0.191 10 5 4.727,3.042 4.894,3.203 0.167,0.161 10 3 5.222,2.343 5.476,2.343 5.476,2.343 5.955,2.766 false 6.04,3.119 6.465,2.382 6.465,2.382 6.639,2.382 false 6.373,3.119 6.661,3.119 false 5.664,3.119 4.878,3.119 false 5.955,3.491 6.359,3.958 6.359,3.958 6.48,3.958 false 0.177,1.162 1.107,1.346 0.930,0.184 10 Free ← Lock:

2.

After the lock to free switch is complete, check the center differential lock detection switch and limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CDL) - 7 (GND1) After lock to free switch is complete 100 kΩ or higher
4 (TL1) - 7 (GND1) After lock to free switch is complete 100 kΩ or higher
5 (TL3) - 7 (GND1) After lock to free switch is complete Below 1 Ω
6 (TL2) - 7 (GND1) After lock to free switch is complete 100 kΩ or higher


If there is a malfunction, replace the transfer shift actuator assembly.





Hide 41450 8.INSPECT DIFFERENTIAL LOCK SHIFT ACTUATOR (w/ Rear Differential Lock)

HINT:

After inspecting the transfer position switch, transfer shift actuator and differential lock switch, check the differential lock shift actuator.


a.

Check the harness and connector (ECU - differential lock shift actuator).

i.

Disconnect the f1 actuator connector.


ii.

Disconnect the A27 and A28 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U164828E02
1.302,1.792 0.979,2.365 false 1.438,1.792 1.604,2.375 false 3.073,1.667 2.844,1.906 2.844,1.906 2.844,2.313 false 3.167,1.927 3.313,2.344 false 5.781,1.677 6.115,1.271 6.115,1.271 6.365,1.271 false 6,1.708 6.323,1.771 6.323,1.771 6.427,1.771 false 5.99,1.948 6.344,2.458 6.344,2.458 6.427,2.458 false 5.76,1.969 5.76,2.333 false 5.563,1.938 5.229,2.438 5.229,2.438 5.167,2.438 false 1.104,0.115 3.677,0.573 2.573,0.458 10 false Front view of wire harness connectors: (to Four Wheel Drive Control ECU) 4.479,0.094 6.875,0.552 2.396,0.458 10 false Front view of wire harness connector: (to Differential Lock Shift Actuator) 1.344,1.135 1.677,1.333 0.333,0.198 10 false A27 3.417,1.115 3.75,1.313 0.333,0.198 10 false A28 2.75,2.354 3.021,2.552 0.271,0.198 10 false M1 3.25,2.365 3.521,2.542 0.271,0.177 10 false M2 1.417,2.396 1.792,2.573 0.375,0.177 10 false RLY2 0.771,2.385 1.146,2.552 0.375,0.167 10 false RLY1 6.458,1.698 6.729,1.896 0.271,0.198 10 false M1 6.458,1.188 6.729,1.365 0.271,0.177 10 false M2 5.635,2.417 6.01,2.594 0.375,0.177 10 false RLY2 6.458,2.385 6.833,2.552 0.375,0.167 10 false RLY1 4.833,2.365 5.198,2.563 0.365,0.198 10 false GND 5.719,1.031 5.865,1.198 0.146,0.167 10 false f1

Standard Resistance:
Tester Connection Condition Specified Condition
A27-9 (RLY1) - f1-6 (RLY1) Always Below 1 Ω
A27-9 (RLY1) - Body ground Always 100 kΩ or higher
A27-10 (RLY2) - f1-5 (RLY2) Always Below 1 Ω
A27-10 (RLY2) - Body ground Always 100 kΩ or higher
A28-1 (M1) - f1-3 (M1) Always Below 1 Ω
A28-1 (M1) - Body ground Always 100 kΩ or higher
A28-5 (M2) - f1-2 (M2) Always Below 1 Ω
A28-5 (M2) - Body ground Always 100 kΩ or higher
f1-4 (GND) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



b.

Check the harness and connector (ECU - differential lock position switch).

i.

Disconnect the f2 differential lock position switch connector.


ii.

Disconnect the A27 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

U164904E02
5.094,1.885 4.333,2.146 4.333,2.146 4.333,2.25 false 5.458,1.896 6.146,2.167 6.146,2.167 6.146,2.25 false 2.583,1.792 2.26,2.354 2.26,2.354 2.104,2.354 false 0.844,0.115 3.417,0.573 2.573,0.458 10 false Front view of wire harness connectors: (to Four Wheel Drive Control ECU) 4.156,0.104 6.552,0.563 2.396,0.458 10 false Front view of wire harness connector: (to Differential Lock Position Switch) 1.938,1.135 2.271,1.333 0.333,0.198 10 false A27 5.229,1.042 5.427,1.198 0.198,0.156 10 false f2 1.823,2.26 2.135,2.427 0.313,0.167 10 false RLP 6.042,2.292 6.292,2.479 0.25,0.188 10 false +B 4.188,2.323 4.583,2.51 0.396,0.188 10 false GND

Standard Resistance:
Tester Connection Condition Specified Condition
A27-15 (RLP) - f2-2 (+B) Always Below 1 Ω
A27-15 (RLP) - Body ground Always 100 kΩ or higher
f2-1 (GND) - Body ground Always Below 1 Ω


If there is a malfunction, repair or replace the harness or connector.



c.

Check the differential lock shift actuator.

i.

Turn the engine switch on (IG).


ii.

Check that there is an operating noise from the differential lock shift actuator when the differential lock switch is switch from OFF to RR (free to lock), or RR to OFF (lock to free).

NOTICE:
·

Perform this operation when the transfer is in low and the center differential is locked.

·

When locking the rear differential, make sure that the vehicle speed is less than 8 km/h (5 mph).



HINT:

Perform this operation when the transfer is in low and the center differential is locked.


OK:

There is an operating noise.


HINT:
·

If the actuator fork cannot move from free to lock or lock to free even though there is an operating noise, there may be a mechanical malfunction in the rear differential.

·

If there is no operating noise, there may be a malfunction in the differential lock shift actuator. However, it may also be a result of a mechanical malfunction in the rear differential, so inspect each part.




iii.

Remove the differential lock shift actuator assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK ACTUATOR(w/ Differential Lock)>REMOVAL).


iv.

Check the free to lock switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the free to lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C175671E03
0.906,3.938 0.969,3.938 0.969,3.938 1.104,4.333 false 1.667,3.896 1.583,3.896 1.583,3.896 1.469,4.333 false 0.854,5.031 0.948,5.031 0.948,5.031 1.188,4.656 false 1.625,4.667 2.052,5.031 2.052,5.031 2.125,5.031 false 1.417,4.667 1.417,5.281 false 6.021,3.229 5.594,2.854 5.594,2.854 5.521,2.854 false 6.094,3.563 6.604,2.823 6.604,2.823 6.708,2.823 false 6.417,3.573 6.698,3.573 false 6.021,3.958 6.323,4.385 6.323,4.385 6.396,4.385 false 5.729,3.594 5.115,3.594 false 5.583,2.146 6.542,2.344 0.958,0.198 10 false DEFOG Relay: 5.406,2.76 5.594,2.938 0.188,0.177 10 false 1 6.427,4.292 6.594,4.49 0.167,0.198 10 false 2 6.781,2.74 6.927,2.906 0.146,0.167 10 false 4 6.781,3.479 6.948,3.667 0.167,0.188 10 false 5 4.958,3.5 5.125,3.656 0.167,0.156 10 false 3 0.365,0.042 2.906,0.396 2.542,0.354 10 false Component without harness connected: (Differential Lock Shift Actuator) 2.667,1.302 3.542,1.521 0.875,0.219 10 false Free → Lock: 0.677,3.854 0.927,4.042 0.25,0.188 10 false M1 1.708,3.813 2,3.958 0.292,0.146 10 false M2 0.479,4.938 0.875,5.094 0.396,0.156 10 false RLY1 1.25,5.333 1.656,5.51 0.406,0.177 10 false RLY2 2.177,4.969 2.573,5.125 0.396,0.156 10 false GND

2.

After the free to lock switch is complete, check the limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND) After free to lock switch is complete Below 12.5 Ω
6 (RLY1) - 4 (GND) After free to lock switch is complete 500 kΩ or higher


If there is a malfunction, replace the differential lock shift actuator assembly.




v.

Check the lock to free switch.

1.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the lock to free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the DEFOG relay.


C175672E03
1.01,3.875 1.063,3.875 1.063,3.875 1.208,4.26 false 1.76,3.802 1.677,3.802 1.677,3.802 1.573,4.25 false 0.969,4.948 1.073,4.948 1.073,4.948 1.313,4.573 false 1.708,4.583 2.135,4.938 2.135,4.938 2.219,4.938 false 1.573,4.573 1.771,5.229 1.771,5.229 1.875,5.229 false 6.115,3.167 5.74,2.792 5.74,2.792 5.677,2.792 false 6.188,3.5 6.771,2.75 6.771,2.75 6.833,2.75 false 6.521,3.5 6.854,3.5 false 6.115,3.896 6.5,4.302 6.5,4.302 6.583,4.302 false 5.823,3.531 5.302,3.531 false 5.688,2.083 6.656,2.281 0.969,0.198 10 false DEFOG Relay: 5.583,2.708 5.771,2.885 0.188,0.177 10 false 1 6.615,4.219 6.781,4.417 0.167,0.198 10 false 2 6.875,2.677 7.021,2.844 0.146,0.167 10 false 4 6.906,3.396 7.073,3.583 0.167,0.188 10 false 5 5.177,3.427 5.344,3.583 0.167,0.156 10 false 3 0.354,0 2.896,0.354 2.542,0.354 10 false Component without harness connected: (Differential Lock Shift Actuator) 0.771,3.781 1.021,3.969 0.25,0.188 10 false M1 1.802,3.74 2.094,3.885 0.292,0.146 10 false M2 0.573,4.875 0.969,5.031 0.396,0.156 10 false RLY1 1.938,5.167 2.344,5.344 0.406,0.177 10 false RLY2 2.271,4.896 2.667,5.052 0.396,0.156 10 false GND 2.552,1.302 3.448,1.521 0.896,0.219 10 false Free ← Lock:

2.

After the lock to free switch is complete, check the limit switch.

(a)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND) After lock to free switch is complete 500 kΩ or higher
6 (RLY1) - 4 (GND) After lock to free switch is complete Below 12.5 Ω


If there is a malfunction, replace the differential lock shift actuator assembly.





d.

Inspect the rear differential lock position switch.


ii.

Measure the resistance according to the value(s) in the table below.

C177818E04
4.833,1.26 4.125,1.323 4.125,1.323 4.125,1.385 false 5.271,1.25 5.958,1.313 5.958,1.313 5.958,1.375 false 3.823,0 6.51,0.406 2.688,0.406 10 false Component without harness connected: (Rear Differential Lock Position Switch) 4.031,1.396 4.323,1.646 0.292,0.25 10 false +B 5.802,1.396 6.219,1.635 0.417,0.24 10 false GND

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (+B) - 1 (GND) Pushed Below 1 Ω
Not pushed 100 kΩ or higher


If there is a malfunction, replace the rear differential lock position switch.



Hide 89533 9.INSPECT 4 WHEEL DRIVE CONTROL ECU

a.

Check the four wheel drive control ECU.

i.

Measure the resistance and voltage according to the value(s) in the table below.

U164548E02
2.698,0.5 3,0.667 0.302,0.167 10 false A27 4.719,0.479 5.021,0.646 0.302,0.167 10 false A28

Tester Connection Terminal Description Condition Specified Condition
A27-1 (HL1) - A28-4 (GND) High-low transfer shift actuator limit switch Engine switch on (IG)
Transfer in high position
Below 1.5 V
Engine switch on (IG)
Transfer in low position
11 to 14 V
Engine switch on (IG)
Transfer in neutral position
11 to 14 V
A27-2 (HL2) - A28-4 (GND) High-low transfer shift actuator limit switch Engine switch on (IG)
Transfer in high position
11 to 14 V
Engine switch on (IG)
Transfer in low position
Below 1.5 V
Engine switch on (IG)
Transfer in neutral position
11 to 14 V
A27-3 (HL3) - A28-4 (GND) High-low transfer shift actuator limit switch Engine switch on (IG)
Transfer in high position
11 to 14 V
Engine switch on (IG)
Transfer in low position
11 to 14 V
Engine switch on (IG)
Transfer in neutral position
Below 1.5 V
A27-5 (TT) - A27-25 (TGND)*1 Temperature sensor Engine switch on (IG) 0 to 5 V
A27-6 (TL1) - A28-4 (GND) Center differential lock actuator limit switch Engine switch on (IG)
Center differential in free position
11 to 14 V
Engine switch on (IG)
Center differential in lock position
11 to 14 V
Engine switch on (IG)
Transfer in neutral position
Below 1.5 V
A27-7 (TL2) - A28-4 (GND) Center differential lock actuator limit switch Engine switch on (IG)
Center differential in free position
11 to 14 V
Engine switch on (IG)
Center differential in lock position
Below 1.5 V
Engine switch on (IG)
Transfer in neutral position
11 to 14 V
A27-8 (TL3) - A28-4 (GND) Center differential lock actuator limit switch Engine switch on (IG)
Center differential in free position
Below 1.5 V
Engine switch on (IG)
Center differential in lock position
11 to 14 V
Engine switch on (IG)
Transfer in neutral position
11 to 14 V
A27-9 (RLY1) - A28-4 (GND)*2 Differential lock shift actuator limit switch Engine switch on (IG)
Rear differential in free position
Below 0.5 V
Engine switch on (IG)
Rear differential in lock position
11 to 14 V
A27-10 (RLY2) - A28-4 (GND)*2 Differential lock shift actuator limit switch Engine switch on (IG)
Rear differential in free position
11 to 14 V
Engine switch on (IG)
Rear differential in lock position
Below 0.5 V
A27-11 (R) - A28-4 (GND)*2 Differential lock switch Engine switch on (IG)
Differential lock switch in OFF position
11 to 14 V
Engine switch on (IG)
Differential lock switch in RR position
Below 1.5 V
A27-12 (DL) - A28-4 (GND) Transfer position switch Engine switch on (IG)
Transfer in high position
11 to 14 V
Engine switch on (IG)
Transfer in low position
Below 1.5 V
A27-13 (LO) - A28-4 (GND) Center differential lock switch Engine switch on (IG)
Center differential lock switch pressed and held
Below 1.5 V
Engine switch on (IG)
Center differential lock switch not pressed
11 to 14 V
A27-14 (P1) - A28-4 (GND) Center differential lock detection switch Engine switch on (IG)
Center differential in free position
11 to 14 V
Engine switch on (IG)
Center differential in lock position
Below 1.5 V
A27-15 (RLP) - A28-4 (GND)*2 Rear differential lock position switch Engine switch on (IG)
Rear differential in free position
11 to 14 V
Engine switch on (IG)
Rear differential in lock position
Below 1.5 V
A27-16 (NP) - A28-4 (GND) Transfer shift actuator neutral position detection switch Engine switch on (IG)
Transfer in neutral position
Below 1.5 V
Engine switch on (IG)
Transfer in high or low position
11 to 14 V
A27-17 (MTN) - A28-4 (GND)*3 Clutch start switch Engine switch on (IG)
Clutch pedal released
11 to 14 V
Engine switch on (IG)
Clutch pedal depressed
Below 2 V
A27-19 (CAN+) - A27-20 (CAN-) CAN communication line Engine switch off 54 to 69 Ω
A27-21 (L4) - A28-4 (GND) Transfer shift actuator Low detection switch Transfer position switch in H4 position 11 to 14 V
Engine switch on (IG)
Transfer position switch in L4 position
Below 1.5 V
A28-1 (M1) - A28-4 (GND)*2 Differential lock shift actuator motor Engine switch on (IG)
Transfer in low position
Center differential in lock position
Differential lock switch OFF → RR
(During operation of differential lock shift actuator motor from free to lock)
11 to 14 V
Engine switch on (IG)
Transfer in low position
Center differential in lock position
Differential lock switch RR → OFF or transfer position switch L4 → H4
(During operation of differential lock shift actuator motor from lock to free)
Below 1.5 V
A28-2 (HM1) - A28-4 (GND) High-low transfer shift actuator motor Engine switch on (IG)
Transfer position switch H4 → L4
(During operation of high-low transfer shift actuator motor from high to low)
Below 1.5 V or alternating between below 1.5 V and 11 to 14 V
Engine switch on (IG)
Transfer position switch L4 → H4
(During operation of high-low transfer shift actuator motor from low to high)
11 to 14 V
A28-3 (IG) - A28-4 (GND) IG power Engine switch on (IG) 11 to 14 V
A28-4 (GND) - Body ground Ground Always Below 1 Ω
A28-5 (M2) - A28-4 (GND)*2 Differential lock shift actuator motor Engine switch on (IG)
Transfer in low position
Center differential in lock position
Differential lock switch OFF → RR
(During operation of differential lock shift actuator motor from free to lock)
Below 1.5 V
Engine switch on (IG)
Transfer in low position
Center differential in lock position
Differential lock switch RR → OFF or transfer position switch L4 → H4
(During operation of differential lock shift actuator motor from lock to free)
11 to 14 V
A28-6 (HM2) - A28-4 (GND) High-low transfer shift actuator motor Engine switch on (IG)
Transfer position switch H4 → L4
(During operation of high-low transfer shift actuator motor from high to low)
11 to 14 V
Engine switch on (IG)
Transfer position switch L4 → H4
(During operation of high-low transfer shift actuator motor from low to high)
Below 1.5 V or alternating between below 1.5 V and 11 to 14 V
A28-7 (TM2) - A28-4 (GND) Center differential lock actuator motor Engine switch on (IG)
Center differential position free → lock
Below 1.5 V or alternating between below 1.5 V and 11 to 14 V
Engine switch on (IG)
Center differential position lock → free
11 to 14 V
A28-8 (TM1) - A28-4 (GND) Center differential lock actuator motor Engine switch on (IG)
Center differential position free → lock
11 to 14 V
Engine switch on (IG)
Center differential position lock → free
Below 1.5 V or alternating between below 1.5 V and 11 to 14 V

If there is a malfunction, inspect the harnesses, connectors, transfer position switch, center differential lock switch, and transfer shift actuator assembly. If these are normal, replace the four wheel drive control ECU (See page Drivetrain>JF2A (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL).

HINT:
·

*1: w/ Temperature Sensor

·

*2: w/ Rear Differential Lock

·

*3: for Manual Transmission