Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 The transfer L4 position switch remains on while the vehicle is running under the following conditions for 1.8 sec. or more (1 trip detection logic).
(a) The output shaft speed is between 1000 and 3000 rpm.
(b) The transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

4 wheel drive control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the transfer-case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

L4 switch indicated that the L4 transfer-case gears are engaged.

·

The transfer-case shifter is in the "H4" position.

·

The transfer-case output shaft rpm is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C238422E06
5.337,1.307 5.567,1.477 0.230,0.170 10 19 5.62,1.195 6.042,1.390 0.422,0.195 10 L4 2.495,1.288 2.725,1.457 0.230,0.170 10 16 2.19,1.195 2.432,1.390 0.242,0.195 10 L4 5.786,2.904 6.308,3.074 0.522,0.170 10 A38*1 5.811,3.221 6.233,3.416 0.422,0.195 10 ECM 1.049,2.111 3.024,2.306 1.974,0.195 10 4 Wheel Drive Control ECU 1.049,1.931 1.471,2.126 0.422,0.195 10 A27 5.791,3.058 6.313,3.228 0.522,0.170 10 A52*2 0.197,3.108 1.684,3.303 1.487,0.195 10 *1: for LHD 0.197,3.108 1.684,3.303 1.487,0.195 10 *1: for LHD 0.197,3.407 1.684,3.602 1.487,0.195 10 *2: for RHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U164577E01
0.055,0.002 2.463,0.370 2.408,0.367 10 Front view of wire harness connector: (to 4 Wheel Drive Control ECU) 1.579,1.132 1.954,1.365 0.375,0.233 10 A27 2.649,2.656 2.908,2.858 0.258,0.202 10 L4 2.785,2.641 2.419,1.975 false

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (L4) - Body ground Always 10 kΩ or higher




OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.
U164902E02
2.771,3.177 2.406,2.125 false 0.052,3.781 0.844,3.958 0.792,0.177 10 false *1: for LHD 0.052,4.198 0.844,4.375 0.792,0.177 10 false *2: for RHD 1.677,1.417 2.052,1.646 0.375,0.229 10 false A52 1.677,1.104 2.052,1.333 0.375,0.229 10 false A38 2.073,1.375 2.271,1.573 0.198,0.198 10 false *2 2.073,1.073 2.271,1.271 0.198,0.198 10 false *1 0.104,0.083 2.51,0.448 2.406,0.365 10 false Front view of wire harness connector: (to ECM) 2.49,3.156 3.021,3.354 0.531,0.198 10 false 19 (L4)

Disconnect the ECM connector.


b.

Disconnect the A27 4 wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-19 (L4) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-19 (L4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR