Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0894  Transmission Component Slipping  P2714  Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)  


DESCRIPTION

C221301E01
4.885,2.063 5.208,1.125 5.208,1.125 5.271,1.125 true 5.031,2.208 5.188,2.573 5.188,2.573 5.26,2.573 true 5.875,2.271 6,2.573 6,2.573 6.063,2.573 true 6.115,2.479 7,2.698 0.885,0.219 10 false Solenoid Coil 0.104,0.677 1.354,0.896 1.25,0.219 10 false Hydraulic Pressure 2.563,3.01 3.125,3.229 0.563,0.219 10 false Current 5.313,2.49 5.844,2.708 0.531,0.219 10 false Sleeve 5.323,1.031 6.167,1.25 0.844,0.219 10 false Spool Valve

The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current of the SLT solenoid valve to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC Code DTC Detection Condition Trouble Area
P0894 The ECM detects a malfunction of the SLT, S1, S2, S3, S4, SL2, gear 6 incorrect ratio (sequence valve) or 1-2 shift solenoid valves according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed

·

Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)


P2714 The ECM detects a malfunction of the SLT shift solenoid valve (ON side) according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic*1, 1 trip detection logic*2).
·

Shift solenoid valve SLT remains open or closed

·

Shift solenoid valve S1, S2, S3, S4 or SL2 remains open or closed

·

Gear 6 incorrect ratio (sequence valve) or 1-2 shift valve is stuck

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)



HINT:
·

*1: w/ OBD

·

*2: w/o OBD



MONITOR DESCRIPTION

The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM illuminates the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.

There are two reasons that make the revolution different.

·

When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.

·

When the shift solenoid valve remains on or off, the gear position commanded by the ECM and the actual gear position are not the same.


NOTICE:

If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.


PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0894 AND P2714)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the tester.

Result
Result Proceed to
P0894 and/or P2714 is output A
P0894, P2714 and other DTCs are output B

HINT:

If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C161166E01
2.116,0.715 2.458,0.905 0.342,0.190 10 SST 2.446,0.517 2.287,0.694 false 0.288,3.989 0.953,4.174 0.666,0.185 10 Test Plug 1.578,3.742 1.107,4.074 1.107,4.074 1.045,4.074 false 0.123,1.731 0.464,1.922 0.342,0.190 10 SST 0.384,1.406 0.294,1.711 false

Remove the test plug on the transmission case center right side and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

b.

Connect the intelligent tester to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure with SST.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.


h.

Measure the line pressure.

ECT
Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLT)* Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

The vehicle is stopped.

·

The engine is idling.



HINT:

*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.


OK:

The line pressure changes as specified when performing the Active Test.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST)
CAUTION:

This test should always be performed with at least 2 people.


NOTICE:
·

Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the intelligent tester to the DLC3.



c.

Warm up the engine.


d.

Enter the following menus: Powertrain / ECT / Active Test.


e.

According to the display on the tester, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.


ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valve and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the tester.




f.

Compare the ECM gear shift command and the actual gear position.

OK:

Gear position changes in accordance with the tester command.


Result
System Condition ECM Gear Shift Command Proceed to
1st 2nd 3rd 4th 5th 6th
Malfunction Shift solenoid valve S1 Stuck ON*1 2nd 2nd 3rd 4th 5th 6th A
Stuck OFF 1st 1st 3rd 4th 5th N*2
Shift solenoid valve S2 Stuck ON 1st 2nd 2nd 4th 6th 6th B
Stuck OFF 3rd 3rd 3rd 4th 5th 5th
Shift solenoid valve S3 Stuck ON 1st 2nd 3rd 3rd N*2 N*2 C
Stuck OFF 3rd 4th 4th 4th 5th 6th
Shift solenoid valve S4 Stuck ON*3 1st 2nd 3rd 4th 5th 6th D
Stuck OFF 1st 2nd 3rd 4th 4th 4th
Normal 1st 2nd 3rd 4th 5th 6th E

HINT:
·

*1: When shift solenoid valve S1 is stuck ON, the vehicle cannot drive in reverse.

·

*2: Neutral

·

*3: When shift solenoid valve S4 is stuck ON, gear shifting is normal.





A

4.INSPECT SHIFT SOLENOID VALVE S1

B

7.INSPECT SHIFT SOLENOID VALVE S2

C

10.INSPECT SHIFT SOLENOID VALVE S3

D

13.INSPECT SHIFT SOLENOID VALVE S4

E

17.INSPECT SHIFT SOLENOID VALVE SLT
4.INSPECT SHIFT SOLENOID VALVE S1
a.
C160563E01
1.71,0.819 1.941,1.002 0.231,0.184 10 (-) 0.056,0 1.633,0.186 1.577,0.186 10 Shift Solenoid Valve S1: 2.477,0.819 2.709,1.002 0.231,0.184 10 (+)

Remove the shift solenoid valve S1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S1 connector

·

Battery negative (-) → Shift solenoid valve S1 body


Valve moves and makes an operating noise




OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

6.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

NG

7.INSPECT SHIFT SOLENOID VALVE S2
a.
C160564E01
2.349,0.818 2.580,1.001 0.231,0.184 10 (+) 0.056,0 1.633,0.186 1.577,0.186 10 Shift Solenoid Valve S2: 3.116,0.818 3.347,1.001 0.231,0.184 10 (-)

Remove the shift solenoid valve S2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S2 connector

·

Battery negative (-) → Shift solenoid valve S2 body


Valve moves and makes an operating noise




OK

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

8.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

9.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

9.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

NG

10.INSPECT SHIFT SOLENOID VALVE S3
a.
C160563E02
1.71,0.819 1.941,1.002 0.231,0.184 10 (-) 0.056,0 1.633,0.186 1.577,0.186 10 Shift Solenoid Valve S3: 2.477,0.819 2.709,1.002 0.231,0.184 10 (+)

Remove the shift solenoid valve S3.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S3 connector terminal - Shift solenoid valve S3 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S3 connector

·

Battery negative (-) → Shift solenoid valve S3 body


Valve moves and makes an operating noise




OK

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

11.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

12.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

12.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

NG

13.INSPECT SHIFT SOLENOID VALVE S4
a.
C123198E03
1.644,0.82 1.876,1.003 0.231,0.184 10 (-) 0.055,0 1.632,0.186 1.577,0.186 10 Shift Solenoid Valve S4: 2.412,0.82 2.643,1.003 0.231,0.184 10 (+)

Remove the shift solenoid valve S4.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S4 connector

·

Battery negative (-) → Shift solenoid valve S4 body


Valve moves and makes an operating noise




OK

14.INSPECT SHIFT SOLENOID VALVE SL2

NG

14.INSPECT SHIFT SOLENOID VALVE SL2
a.
C358507E02
1.104,3.021 1.552,3.292 false 1.844,1.198 2.292,0.896 false 1.854,3.323 2.344,2.938 false 1.104,0.917 1.552,1.188 false 0.229,0.042 2.677,0.385 2.448,0.344 10 false Component without harness connected: (Shift Solenoid Valve SL2) 0.969,0.792 1.125,0.99 0.156,0.198 10 false 2 2.344,0.792 2.5,0.99 0.156,0.198 10 false 1 0.969,2.844 1.125,3.042 0.156,0.198 10 false 2 2.406,2.813 2.563,3.01 0.156,0.198 10 false 1 1.219,4.323 1.417,4.521 0.198,0.198 10 false (-) 2.031,4.323 2.229,4.521 0.198,0.198 10 false (+)

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise




OK

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

15.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

16.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

16.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

NG

17.INSPECT SHIFT SOLENOID VALVE SLT
a.
C358531E01
1.875,1.208 2.344,0.844 false 1.594,1.229 1.073,0.813 false 1.865,3.344 2.333,2.979 false 1.583,3.344 1.063,2.927 false 0.104,0.042 2.573,0.417 2.469,0.375 10 false Component without harness connected: (Shift Solenoid Valve SLT) 2.406,0.688 2.563,0.885 0.156,0.198 10 false 1 0.948,0.667 1.104,0.865 0.156,0.198 10 false 2 2.375,2.833 2.531,3.031 0.156,0.198 10 false 1 0.906,2.792 1.063,2.99 0.156,0.198 10 false 2 1.271,4.344 1.479,4.542 0.208,0.198 10 false (+) 2.01,4.333 2.219,4.531 0.208,0.198 10 false (-)

Remove the shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise




OK

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

18.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

19.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

19.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
a.

Check the torque converter clutch assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).

OK:

The torque converter clutch operates normally.




OK

NG