Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255267 AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1VD-FTV)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 5.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51440 7.REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483

a.

Remove the 4 bolts and oil pan protector.


Hide 53782 8.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 53784 9.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 33702B 11.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.


Hide 37140 12.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 13.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 32101A 16.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

A170323

a.

Remove the 2 bolts and oil pan insulator.


b.
C171531

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


Hide 32907A 17.DISCONNECT OIL COOLER TUBE

C177423

a.

Disconnect the 2 transmission oil cooler hoses from the oil cooler tube union.


b.

Remove the 3 bolts and separate the oil cooler tube from the engine.


Hide 35000 18.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C161356

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


Hide 51203 19.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484

a.

Remove the engine mounting hole cover.


b.
C171489

Remove the 4 bolts of the rear engine mounting insulator.


c.
U164644

Remove the 4 nuts, 4 bolts and frame crossmember.


Hide 12371 20.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C172398

a.

Remove the 4 bolts and rear engine mounting insulator from the transmission.


Hide 35104V 21.DISCONNECT BREATHER PLUG HOSE

C171532

a.

Disconnect the 3 breather plug hoses from the wire harness.


Hide 22.DISCONNECT WIRE HARNESS AND CONNECTOR

C171503

a.

Remove the bolt and disconnect the ground cable.


b.
U152359

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



c.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.

U164680

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



d.

Disconnect the 8 harness clamps.


e.

Remove the 2 bolts and disconnect the wire harness.


Hide 12140 23.REMOVE OIL PAN COVER

C172394

a.

Remove the 2 bolts and oil pan cover.


Hide 35119A 24.REMOVE TRANSMISSION HOUSING COVER

C175581

a.

Remove the 3 bolts and transmission housing cover.


Hide 35000 25.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C175537

a.

Remove the 10 bolts and transmission.

NOTICE:

Do not use excess force to pry off the transmission assembly.



Hide 36100 26.REMOVE TRANSFER ASSEMBLY

C171493

a.

Remove the 7 bolts and transfer case lower protector.


b.
C171523

Remove the 8 bolts and transfer.


Hide 32000 27.REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY