Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0705 One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

P input signal

·

N input signal

·

R input signal

·

D input signal


(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

NSW input signal

·

R input signal

·

D input signal


(C) Any of following signals are ON for 2.0 seconds or more in S position (2 trip detection logic):
·

NSW input signal

·

P input signal

·

N input signal

·

R input signal


(D) P, R, N and D switches are OFF simultaneously (2 trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

Transmission control switch (lower shift lever assembly)

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C177781E30
5.448,2.365 5.771,2.563 0.323,0.198 10 false C45 5.448,2.969 5.771,3.167 0.323,0.198 10 false C45 5.458,3.573 5.781,3.771 0.323,0.198 10 false C45 5.458,4.167 5.781,4.365 0.323,0.198 10 false C45 5.458,1.198 5.781,1.396 0.323,0.198 10 false C45 5.833,5.854 6,6.052 0.167,0.198 10 false S 5.833,4.125 6,4.323 0.167,0.198 10 false P 5.833,3.563 6,3.76 0.167,0.198 10 false R 5.833,2.969 6,3.167 0.167,0.198 10 false N 5.813,2.365 5.979,2.563 0.167,0.198 10 false D 3.688,2.229 3.938,2.427 0.25,0.198 10 false DL 3.698,2.854 3.948,3.052 0.25,0.198 10 false NL 3.729,3.396 3.979,3.594 0.25,0.198 10 false RL 3.656,4.042 3.906,4.24 0.25,0.198 10 false PL 2.99,1.823 3.24,2.021 0.25,0.198 10 false B 2.99,3.104 3.24,3.302 0.25,0.198 10 false RB 0.604,3.281 1.979,3.479 1.375,0.198 10 false from BK/UP LP Fuse 5.51,2.771 5.76,2.969 0.25,0.198 10 false 25 5.51,2.188 5.76,2.385 0.25,0.198 10 false 27 5.51,3.375 5.76,3.573 0.25,0.198 10 false 26 5.5,5.677 5.75,5.875 0.25,0.198 10 false 25 5.531,3.979 5.781,4.177 0.25,0.198 10 false 2 5.458,1 5.76,1.198 0.302,0.198 10 false 120 3.969,4.281 4.135,4.479 0.167,0.198 10 false 6 3.969,2.042 4.135,2.24 0.167,0.198 10 false 5 3.969,3.688 4.135,3.885 0.167,0.198 10 false 1 2.771,3.406 2.938,3.604 0.167,0.198 10 false 2 2.781,2.052 2.948,2.25 0.167,0.198 10 false 4 3.969,3.083 4.135,3.281 0.167,0.198 10 false 9 3.969,2.49 4.135,2.688 0.167,0.198 10 false 7 5.458,5.885 5.781,6.083 0.323,0.198 10 false A38 2.552,4.635 2.885,4.833 0.333,0.198 10 false C24 5.802,1.198 6.198,1.396 0.396,0.198 10 false NSW 6.125,7.052 6.5,7.25 0.375,0.198 10 false ECM 2.552,4.823 4.469,5.021 1.917,0.198 10 false Park/Neutral Position Switch 2.531,6.406 2.948,6.604 0.417,0.198 10 false E52 0.896,5.906 1.979,6.104 1.083,0.198 10 false from LH-IG Fuse 2.531,6.594 4.396,6.792 1.865,0.198 10 false Transmission Control Switch 2.781,5.99 2.979,6.188 0.198,0.198 10 false 3 3.969,5.99 4.198,6.188 0.229,0.198 10 false 7 2.99,5.729 3.24,5.927 0.25,0.198 10 false IG 3.792,5.729 4.042,5.927 0.25,0.198 10 false S 3.76,1.802 4.01,2 0.25,0.198 10 false L 4.5,1.917 5.281,2.115 0.781,0.198 10 false to ST Relay 0.198,1.927 2.01,2.125 1.813,0.198 10 false from Main Body ECU (STR)

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever is:
·

In P or N: ON

·

Not in P or N: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever is:
·

In P: ON

·

Not in P: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever is:
·

In R: ON

·

Not in R: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever is:
·

In N: ON

·

Not in N: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Continuously shift to "+" (up-shift)

·

OFF: Release "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Continuously shift to "-" (down-shift)

·

OFF: Release "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
Shift lever position is:
·

ON: In S, "+" and "-"

·

OFF: Not in S, "+" and "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever is:
·

In D, S, "+" and "-": ON

·

Not in D, S, "+" and "-": OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.



PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E47
1.656,0.74 1.125,0.302 false 1.125,1.385 1.656,0.958 false 0.052,0.052 0.365,0.25 0.313,0.198 10 false *a 0.896,0.188 1.135,0.385 0.24,0.198 10 false IG 0.938,1.313 1.125,1.51 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

2.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)

NG

REPLACE TRANSMISSION CONTROL SWITCH (LOWER SHIFT LEVER ASSEMBLY)

2.CHECK TRANSMISSION CONTROL SWITCH (POWER SOURCE)
a.
U164956E02
1.802,1.063 2.344,0.75 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.406,0.656 2.719,0.854 0.313,0.198 10 false IG 0.542,1 0.917,1.229 0.375,0.229 10 false E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY)

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E91
1.844,0.958 2.219,0.417 false 1.292,0.958 0.917,0.417 false 2.094,1.271 2.458,1.813 false 0.99,1.781 1.365,1.24 false 1.604,0.958 1.521,0.417 false 2.031,1.813 1.948,1.271 false 1.635,1.823 1.719,1.281 false 2.26,0.25 2.573,0.448 0.313,0.198 10 false RL 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.76,0.25 1.073,0.448 0.313,0.198 10 false B 2.51,1.76 2.823,1.958 0.313,0.198 10 false L 0.781,1.792 1.094,1.99 0.313,0.198 10 false NL 1.25,0.25 1.563,0.448 0.313,0.198 10 false RB 1.99,1.844 2.302,2.042 0.313,0.198 10 false PL 1.521,1.875 1.833,2.073 0.313,0.198 10 false DL

Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)



OK

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

NG

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U164954E02
1.802,1.01 2.177,0.323 false 0.365,1.042 0.74,1.271 0.375,0.229 10 false C24 2.229,0.229 2.542,0.427 0.313,0.198 10 false RB 0.052,0 0.365,0.198 0.313,0.198 10 false *a

Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V
C24-2 (RB) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.
U165017E02
0.313,1.646 0.76,0.813 false 2.396,1.698 1.417,1.333 false 0.844,1.813 0.76,0.906 false 1.24,1.688 0.833,0.917 false 1.844,1.885 0.906,0.927 false 0.094,0.083 0.385,0.292 0.292,0.208 10 false *a 1.458,0.302 1.833,0.531 0.375,0.229 10 false C45 0.146,1.656 0.531,1.854 0.385,0.198 10 false 2 (P) 2.188,1.729 2.938,1.927 0.75,0.198 10 false 120 (NSW) 1.708,1.917 2.177,2.115 0.469,0.198 10 false 27 (D) 0.646,1.865 1.094,2.063 0.448,0.198 10 false 25 (N) 1.083,1.677 1.531,1.875 0.448,0.198 10 false 26 (R)

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C45-2 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever in P


11 to 14 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V*
C45-25 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever in N


11 to 14 V
C45-27 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever in D


11 to 14 V
C45-120 (NSW) - Body ground
·

Engine switch on (IG)

·

Shift lever not in P or N


11 to 14 V
C45-2 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever not in P


Below 1 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever not in R


Below 1 V
C45-25 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever not in N


Below 1 V
C45-27 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever not in D


Below 1 V
C45-120 (NSW) - Body ground
·

Engine switch on (IG)

·

Shift lever in P or N


Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)

HINT:

*: The voltage will drop slightly due to turning on the back up light.




OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
U164938E02
2.219,1.802 1.969,0.99 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.625,0.271 2,0.5 0.375,0.229 10 false A38 2.042,1.823 2.49,2.021 0.448,0.198 10 false 25 (S)

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" and "-"


11 to 14 V
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" and "-"


Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR