Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  P0973  Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1)  P0974  Shift Solenoid "A" Control Circuit High (Shift Solenoid Valve S1)  


DESCRIPTION

Shifting from 1st to 6th is performed in combination with ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely. Also, the ECM stops sending the current to the open or short circuited solenoid (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0973 ECM detects a short in the solenoid valve S1 circuit 2 times when solenoid valve S1 is operated (1 trip detection logic).
·

Short in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

ECM


P0974 ECM detects an open in the solenoid valve S1 circuit 2 times when solenoid valve S1 is not operated (1 trip detection logic).
·

Open in shift solenoid valve S1 circuit

·

Shift solenoid valve S1

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve S1 circuit. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. When shift solenoid valve S1 is ON, if its resistance is 8 Ω or less, the ECM determines there is a short in the shift solenoid valve S1 circuit.

When shift solenoid valve S1 is OFF, if its resistance is 100 kΩ or more, the ECM determines there is an open in the shift solenoid valve S1 circuit (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>FAIL-SAFE CHART).

WIRING DIAGRAM

C214968E11
5.779,2.943 6.148,3.113 0.369,0.170 10 C45 5.779,3.097 6.201,3.292 0.422,0.195 10 ECM 5.638,1.203 6.007,1.373 0.369,0.170 10 S1 5.411,1.331 5.545,1.501 0.134,0.170 10 7 3.628,1.331 3.777,1.501 0.149,0.170 10 8 3.314,1.081 3.546,1.251 0.232,0.170 10 S1 1.435,2.684 1.804,2.853 0.369,0.170 10 C34 1.435,2.838 3.079,3.033 1.644,0.195 10 No. 1 Transmission Wire 1.533,1.69 3.177,1.885 1.644,0.195 10 Shift Solenoid Valve S1

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve S1 is turned ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S1 OFF ON ON ON ON ON


PROCEDURE

1.INSPECT NO. 1 TRANSMISSION WIRE (SHIFT SOLENOID VALVE S1)
a.
C214326E33
1.221,1.087 0.967,1.745 false 0.055,0.021 0.279,0.187 0.224,0.167 10 *a 0.84,1.783 1.076,1.950 0.236,0.167 10 S1

Disconnect the No. 1 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Component without harness connected
(No. 1 Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE S1
2.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - ECM)
a.
U165023E01
0.091,0.037 0.386,0.245 0.296,0.208 10 *a 1.457,0.269 1.832,0.502 0.375,0.233 10 C45 0.499,1.771 1.171,1.938 0.672,0.168 10 7 (S1) 1.139,0.814 0.686,1.733 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-7 (S1) - Body ground 20°C (68°F) 11 to 15 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR