Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  P0778  Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)  


DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated safely (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>FAIL-SAFE CHART).

DTC Code DTC Detection Condition Trouble Area
P0778 The ECM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears (1 trip detection logic).
Output signal duty ratio equals to 100%.
HINT:

SL2 output signal duty ratio is less than 100% under normal condition.


·

Open or short in shift solenoid valve SL2 circuit

·

Shift solenoid valve SL2

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Also, the ECM performs the fail-safe function and turns the other shift solenoid valves that are in good condition ON/OFF. In the case of an open or short circuit, the ECM stops sending the current to the open or short circuited solenoid.

While driving and shifting gears, if the ECM detects an open or short in the shift solenoid valve SL2 circuit, the ECM determines there is a malfunction (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)>FAIL-SAFE CHART).

WIRING DIAGRAM

C219459E06
5.739,1.181 6.140,1.370 0.400,0.190 10 SL2+ 5.739,2.398 6.140,2.587 0.400,0.190 10 SL2- 2.345,1.061 2.746,1.250 0.400,0.190 10 SL2+ 2.345,2.279 2.746,2.468 0.400,0.190 10 SL2- 5.927,3.37 6.328,3.560 0.400,0.190 10 ECM 5.926,3.199 6.327,3.389 0.400,0.190 10 C45 2.801,2.508 2.993,2.698 0.192,0.190 10 4 2.801,1.291 2.993,1.481 0.192,0.190 10 2 5.456,1.291 5.648,1.481 0.192,0.190 10 12 5.454,2.508 5.646,2.698 0.192,0.190 10 13 1.019,1.741 2.596,1.931 1.576,0.190 10 Shift Solenoid Valve SL2 0.93,3.099 2.521,3.289 1.590,0.190 10 No. 2 Transmission Wire 0.93,2.925 1.331,3.114 0.400,0.190 10 C96 0.805,1.393 0.997,1.582 0.192,0.190 10 1 0.8,2.171 0.992,2.360 0.192,0.190 10 2

CAUTION / NOTICE / HINT

HINT:

Shift solenoid valve SL2 is turned ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL2 ON ON ON ON OFF OFF


PROCEDURE

1.INSPECT NO. 2 TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2)
a.
C219458E01
0.654,0.519 1.087,0.664 0.434,0.145 10 SL2+ 0.126,0.095 0.560,0.299 0.434,0.204 10 *a 0.654,1.656 1.091,1.801 0.437,0.145 10 SL2- 1.13,0.604 1.588,1.027 false 1.588,1.331 1.13,1.753 false

Disconnect the No. 2 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SL2+) - 4 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SL2+) - Body ground Always 10 kΩ or higher
4 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(No. 2 Transmission Wire)



OK

2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL2
2.CHECK HARNESS AND CONNECTOR (NO. 2 TRANSMISSION WIRE - ECM)
a.
U165022E01
0.091,0.037 0.386,0.245 0.296,0.208 10 *a 1.457,0.269 1.832,0.502 0.375,0.233 10 C45 0.669,1.789 1.426,1.957 0.757,0.168 10 12 (SL2+) 1.744,1.795 2.508,1.963 0.764,0.168 10 13 (SL2-) 1.493,0.825 1.097,1.764 false 1.573,0.822 1.979,1.764 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-12 (SL2+) - C45-13 (SL2-) 20°C (68°F) 5.0 to 5.6 Ω
C45-12 (SL2+) - Body ground Always 10 kΩ or higher
C45-13 (SL2-) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR