Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd mode is selected with the pattern select (2nd) switch, the ECM controls the shift solenoid valves and the transmission starts from 2nd gear.

The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.

When the shift lever is in D, the transmission automatically shifts up through 3rd to 6th as usual.

CAUTION / NOTICE / HINT

When the pattern select (2nd) switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the pattern select (2nd) switch once again.

HINT:

2nd mode is automatically canceled when the engine switch is turned off.


PROCEDURE

1.DRIVING TEST
HINT:

The driving test should be performed on a paved road (nonskid road).


a.

Start the engine.


b.

Turn the 2nd switch off (normal drive mode).


c.

Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.


d.

Turn the 2nd switch on and perform the same check as above.

When driving the vehicle with the 2nd switch on and off, check that there is a difference in acceleration.

OK:

There is a difference in acceleration.




OK

NG

2.INSPECT PATTERN SELECT (2ND) SWITCH
2.INSPECT PATTERN SELECT (2ND) SWITCH
a.
C238423E10
2.281,1.762 2.870,1.964 0.590,0.202 10 2ND 0.049,0 0.245,0.202 0.195,0.202 10 *a 2.417,1.743 1.944,1.082 false 1.255,1.762 1.559,1.964 0.303,0.202 10 E 1.343,1.743 1.624,1.286 false

Remove the suspension control switch (See page Suspension>SUSPENSION CONTROL>ABSORBER CONTROL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (2ND) - 16 (E) Pattern select (2nd) switch continuously pressed Below 1 Ω
4 (2ND) - 16 (E) Pattern select (2nd) switch released 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Suspension Control Switch)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (2ND) SWITCH (SUSPENSION CONTROL SWITCH)

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)
a.
U165081E01
1.931,1.704 1.799,1.389 false 1.889,1.704 2.163,1.906 0.274,0.202 10 E 0.057,0.005 0.252,0.207 0.195,0.202 10 *a 0.334,0.979 0.709,1.212 0.375,0.233 10 V4

Disconnect the suspension control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-16 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)



OK

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)
a.
U164937E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.621,0.22 1.996,0.453 0.375,0.233 10 A38 1.137,1.782 1.813,1.983 0.676,0.202 10 4 (SNWI) 1.532,1.756 1.834,0.808 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-4 (SNWI) - Body ground Pattern select (2nd) switch continuously pressed Below 1 Ω
A38-4 (SNWI) - Body ground Pattern select (2nd) switch released 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR