The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0766 | S4 stuck OFF malfunction or brake control valve malfunction*1: Shifting to 5th and 6th gears is impossible. The ECM determines there is a malfunction when the following conditions are both met. (2 trip detection logic*2, 1 trip detection logic*3) (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th. (b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th. |
·
Shift solenoid valve S4 remains closed ·
Shift solenoid valve SLT remains open or closed ·
Valve body is blocked (Brake control valve) ·
Automatic transmission (clutch, brake, gear, etc.) |
| P0776 | SL2 stuck ON malfunction or brake control valve malfunction*1: Shifting to 5th and 6th gears is impossible. The ECM determines there is a malfunction when the following conditions are both met (2 trip detection logic): (a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th. (b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th. |
·
Shift solenoid valve SL2 remains open ·
Shift solenoid valve SLT remains open or closed ·
Valve body is blocked (Brake control valve) ·
Automatic transmission (clutch, brake, gear, etc.) |
*2: w/ OBD
*3: w/o OBD
Gear positions in the event of a solenoid valve mechanical problem:
| ECM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under malfunction | 1st | 2nd | 3rd | 4th | 4th | 4th |
Gear position during fail-safe operation:
If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under fail-safe mode | 1st | 2nd | 3rd | 3rd | 3rd | 3rd |
This DTC indicates a stuck OFF malfunction of shift solenoid valve S4, stuck ON malfunction of shift solenoid valve SL2, or brake control valve malfunction. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
While driving, the shift position can be forcibly changed with the GTS.
Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)>FAIL-SAFE CHART).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valves and set each shift position by yourself | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Possible to check operation of the shift solenoid valves.
[Vehicle Condition] 50 km/h (30 mph) or less |
This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.
The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.
The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the Data List display on the GTS.
Shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.
| ECM command gearshift | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S4 | OFF | OFF | OFF | OFF | ON | ON |
| Shift solenoid valve SL2 | ON | ON | ON | ON | OFF | OFF |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only P0766 and P0776 are output | A |
| P0766, P0776 and other DTCs are output | B |
If any other codes besides P0766 and P0776 are output, perform troubleshooting for those DTCs first.
A
B
OK
NG
Remove the shift solenoid valve S4.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S4 connector ·
Battery negative (-) → Shift solenoid valve S4 body |
Valve moves and makes an operating noise |
| *a | Component without harness connected
(Shift Solenoid Valve S4) |
OK
NG
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| *a | Component without harness connected
(Shift Solenoid Valve SL2) |
OK
NG
OK
NG