1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53806
3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51405A
5.REMOVE NO. 1 ENGINE UNDER COVER
51442
6.REMOVE NO. 2 ENGINE UNDER COVER
51440
7.REMOVE OIL PAN PROTECTOR ASSEMBLY
Remove the 4 bolts and oil pan protector assembly.
8.DRAIN AUTOMATIC TRANSMISSION FLUID
53782
9.REMOVE FRONT FENDER APRON TRIM PACKING A
53784
10.REMOVE FRONT FENDER APRON TRIM PACKING C
11.DRAIN ENGINE COOLANT
33702B
12.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
Remove the clip and pin and disconnect the gear shifting rod from the transmission control shaft lever RH.
37140
13.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110
14.REMOVE PROPELLER SHAFT ASSEMBLY
15.REMOVE EXHAUST PIPE
17118
16.REMOVE MANIFOLD STAY
17119
17.REMOVE NO. 2 MANIFOLD STAY
28100
18.REMOVE STARTER ASSEMBLY
32101A
19.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.
16278
20.DISCONNECT NO.2 WATER BY-PASS PIPE (w/ ATF Warmer)
Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then disconnect the No. 2 water by-pass pipe from the automatic transmission assembly.
Use a container to catch any coolant which flows out of the water by-pass hoses.
32943B
21.DISCONNECT TRANSMISSION OIL COOLER HOSE (w/ ATF Warmer)
Disconnect the 2 transmission oil cooler hoses from the transmission oil thermostat.
32943B
22.DISCONNECT TRANSMISSION OIL COOLER HOSE (w/o ATF Warmer)
Disconnect the 2 transmission oil cooler hoses from the oil cooler tube unions.
35000
23.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.
Support the oil pan bolts to prevent damage to the oil pan gasket.
51203
24.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the engine mounting hole cover.
Remove the 4 bolts of the rear engine mounting insulator.
Remove the 4 nuts, 4 bolts and No. 3 frame crossmember.
12371
25.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the 2 bolts and engine mounting heat insulator.
Remove the 4 bolts and rear engine No. 1 mounting insulator from the transmission.
26.DISCONNECT WIRE HARNESS AND CONNECTOR
Remove the bolt and disconnect the ground cable.
Tilt the transmission downward.
Support the oil pan bolts to prevent damage to the oil pan gasket.
Make sure the cooling fan does not contact the fan shroud.
Remove the 4 wire harness clamps.
Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control connectors.
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
Detach the 4 connector clamps and 11 harness clamps.
35000
27.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
Remove the 10 bolts and transmission.
Do not use excess force to pry off the transmission assembly.
33490F
28.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)
Remove the 3 bolts and transmission oil cooler assembly with transmission oil thermostat.
| *1 | Transmission Oil Cooler Assembly |
| *2 | Transmission Oil Thermostat |
| *3 | O-ring |
Disconnect the transmission oil cooler assembly from the transmission oil thermostat.
Remove the 2 O-rings from the transmission oil cooler assembly.
Remove the 2 O-rings from the transmission oil thermostat.
36407
29.DISCONNECT TRANSFER BREATHER HOSE SUB-ASSEMBLY
Disconnect the 2 breather plug hoses from the harness clamp bracket.
Detach the 3 breather hose clamps from the automatic transmission breather tube.
36179
30.REMOVE LOWER TRANSFER CASE PROTECTOR
Detach the clamp of the ground cable from the lower transfer case protector.
Remove the 7 bolts and lower transfer case protector.
36100
31.REMOVE TRANSFER ASSEMBLY
32.REMOVE HARNESS CLAMP BRACKET
Remove the 8 bolts and 8 harness clamp brackets.
32000
33.REMOVE TORQUE CONVERTER ASSEMBLY