Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  P0781  1-2 Shift (1-2 Shift Valve)  


DESCRIPTION

The 1-2 shift valve performs shifting to 1st gear and other gears. When shifting to 2nd and 4th gears is impossible, or when the ECM directs the gearshift to switch to 5th and 6th gear and the engine overruns (clutch slips), this DTC is output.

DTC Code DTC Detection Condition Trouble Area
P0781

When conditions (a) and (b), or (a) and (c) are met. (2 trip detection logic*1, 1 trip detection logic*2)


(a) When the ECM directs the transmission to switch to 2nd gear, the actual gear is shifted to 1st.
(b) When the ECM directs the transmission to switch to 4th gear, the actual gear is shifted to 3rd.
(c) When the ECM directs the transmission to switch to 5th gear, the engine overruns (clutch slips).
·

Valve body is blocked up or stuck (1-2 shift valve)

·

Shift solenoid valve SLT remains open or closed

·

Automatic transmission (clutch, brake, gear, etc.)



*1: w/ OBD

*2: w/o OBD


HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM command gearshift 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 1st 3rd 3rd N* N*

N*: Neutral

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.


Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
Actual gear position under fail-safe mode 1st* 1st* 3rd 3rd 3rd 3rd

1st*: Under engine braking, downshifting to 1st or 2nd gear is prohibited.



MONITOR DESCRIPTION

This DTC indicates that the 1-2 shift valve in the valve body is locked in the position in which the spring is compressed.

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF and switching oil pressure to the valves in the valve body.

The ECM calculates the actual transmission gear by comparing the signals from the input speed sensor (NT) and the output speed sensor (SP2). The ECM can detect many mechanical problems in the shift solenoids, valve body, transmission clutches, brakes, and gears. If the ECM detects that the actual gear position and commanded gear position are different, it will illuminate the MIL and store the DTC.

PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0781)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the GTS.

Result
Result Proceed to
Only P0781 is output A
P0781 and other DTCs are output B

HINT:

If any other codes besides P0781 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (RUNNING TEST)

B

2.PERFORM ACTIVE TEST USING GTS (RUNNING TEST)
CAUTION:

This test should always be performed with at least 2 people.


NOTICE:
·

Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).

·

Perform the test with the A/C turned off.



HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


a.

Connect the GTS to the DLC3.



c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

According to the display on the GTS, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the GTS.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)>FAIL-SAFE CHART).


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position by yourself
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the GTS.

·

Gear positions in the event of a solenoid valve mechanical problem:

Tester command gearshift 1st 2nd 3rd 4th 5th 6th
Actual gear position under malfunction 1st 1st 3rd 3rd N* N*

N*: Neutral

OK:

Gear position changes in accordance with the GTS command.






OK

3.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

3.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

OK

4.CLEAR DTC AND PERFORM RUNNING TEST

NG