Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255275 AUTOMATIC TRANSMISSION ASSEMBLY(for 1UR-FE) A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1UR-FE)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53806 3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51440 7.REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483

a.

Remove the 4 bolts and oil pan protector assembly.


Hide 53782 9.REMOVE FRONT FENDER APRON TRIM PACKING A

Hide 53784 10.REMOVE FRONT FENDER APRON TRIM PACKING C

Hide 33702B 12.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Remove the clip and pin and disconnect the gear shifting rod from the transmission control shaft lever RH.


Hide 37140 13.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 14.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 11452 18.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17167 19.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17104 20.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 32101A 23.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
C161354

Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


Hide 16278 24.DISCONNECT NO.2 WATER BY-PASS PIPE (w/ ATF Warmer)

a.
C258389

Remove the bolt and disconnect the 2 water by-pass hoses from the transmission oil cooler. Then disconnect the No. 2 water by-pass pipe from the automatic transmission assembly.

NOTICE:

Use a container to catch any coolant which flows out of the water by-pass hoses.



Hide 32943B 25.DISCONNECT TRANSMISSION OIL COOLER HOSE (w/ ATF Warmer)

a.
C162139

Disconnect the 2 transmission oil cooler hoses from the transmission oil thermostat.


Hide 32943B 26.DISCONNECT TRANSMISSION OIL COOLER HOSE (w/o ATF Warmer)

C181045

a.

Disconnect the 2 transmission oil cooler hoses from the oil cooler tube unions.


Hide 35000 27.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C161356

a.

Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

NOTICE:

Support the oil pan bolts to prevent damage to the oil pan gasket.



Hide 51203 28.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484

a.

Remove the engine mounting hole cover.


b.
C171489

Remove the 4 bolts of the rear engine mounting insulator.


c.
U164644

Remove the 4 nuts, 4 bolts and No. 3 frame crossmember.


Hide 12371 29.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C172399

a.

Remove the 2 bolts and engine mounting heat insulator.


b.

Remove the 4 bolts and rear engine No. 1 mounting insulator from the transmission.


Hide 30.DISCONNECT WIRE HARNESS AND CONNECTOR

C171503

a.

Remove the bolt and disconnect the ground cable.


b.
U152359

Tilt the transmission downward.

NOTICE:
·

Support the oil pan bolts to prevent damage to the oil pan gasket.


·

Make sure the cooling fan does not contact the fan shroud.




c.
C228999

Remove the 4 wire harness clamps.


d.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 3 transfer control connectors.

C228368

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



e.

Detach the 4 connector clamps and 11 harness clamps.


Hide 35000 31.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C175536

a.

Remove the 10 bolts and transmission.

NOTICE:

Do not use excess force to pry off the transmission assembly.



Hide 33490F 32.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)

a.
C175538E03
1.677,2.277 1.833,2.458 0.156,0.181 10 *1 2.529,4.315 2.685,4.496 0.156,0.181 10 *3 2.956,3.012 3.112,3.193 0.156,0.181 10 *2 1.155,3.899 1.311,4.080 0.156,0.181 10 *3 1.371,2.808 1.565,2.369 1.565,2.369 1.663,2.369 false 2.656,3.553 2.85,3.115 2.85,3.115 2.947,3.115 false 1.651,3.545 1.457,3.983 1.457,3.983 1.36,3.983 false 2.957,4.102 2.828,4.393 2.828,4.393 2.73,4.393 false 2.828,4.393 3.061,4.278 false 1.457,3.983 1.44,3.575 false

Remove the 3 bolts and transmission oil cooler assembly with transmission oil thermostat.

Text in Illustration
*1 Transmission Oil Cooler Assembly
*2 Transmission Oil Thermostat
*3 O-ring


b.

Disconnect the transmission oil cooler assembly from the transmission oil thermostat.


c.

Remove the 2 O-rings from the transmission oil cooler assembly.


d.

Remove the 2 O-rings from the transmission oil thermostat.


Hide 36407 33.DISCONNECT TRANSFER BREATHER HOSE SUB-ASSEMBLY

a.
C175541

Disconnect the 2 breather plug hoses from the harness clamp bracket.


b.
C228919

Detach the 3 breather hose clamps from the automatic transmission breather tube.


Hide 36179 34.REMOVE LOWER TRANSFER CASE PROTECTOR

a.
C171493

Detach the clamp of the ground cable from the lower transfer case protector.


b.

Remove the 7 bolts and lower transfer case protector.


Hide 36.REMOVE HARNESS CLAMP BRACKET

a.

Remove the 8 bolts and 8 harness clamp brackets.

C228367


Hide 32000 37.REMOVE TORQUE CONVERTER ASSEMBLY