Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 The transfer L4 position switch remains on while the vehicle is running under the following conditions for 1.8 sec. or more (1 trip detection logic).
(a) The output shaft speed is between 1000 and 3000 rpm.
(b) The transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

4 wheel drive control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the L4 switch indicates that the transfer-case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The transfer-case shifter is in the "H4" position.

·

The transfer-case output shaft rpm is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C258072E11
5.183,1.072 5.413,1.242 0.230,0.170 10 21 5.505,0.979 5.927,1.175 0.422,0.195 10 L4 1.846,1.072 2.076,1.242 0.230,0.170 10 16 1.503,0.979 1.745,1.175 0.242,0.195 10 L4 0.372,2.466 2.347,2.661 1.974,0.195 10 4 Wheel Drive Control ECU 0.372,2.285 0.794,2.480 0.422,0.195 10 A27 5.62,2.668 6.001,2.864 0.382,0.196 10 ECM 5.62,2.294 6.063,2.496 0.443,0.202 10 A38*1 5.62,2.48 6.063,2.682 0.443,0.202 10 A52*2 0.04,3.047 0.835,3.221 0.795,0.174 10 *1: for LHD 0.04,3.392 0.835,3.567 0.795,0.174 10 *2: for RHD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U164968E01
0.057,0.005 0.374,0.206 0.317,0.202 10 *a 1.571,0.194 1.947,0.427 0.375,0.233 10 A27 2.678,1.702 2.923,1.904 0.245,0.202 10 L4 2.708,1.688 2.428,1.124 false

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-16 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.
U165068E01
1.186,0.244 1.561,0.477 0.375,0.233 10 A38 1.603,0.244 1.796,0.477 0.193,0.233 10 *1 2.017,0.244 2.392,0.477 0.375,0.233 10 A52 2.433,0.244 2.626,0.477 0.193,0.233 10 *2 0.116,0.07 0.317,0.272 0.200,0.202 10 *a 1.618,1.65 2.145,1.851 0.527,0.202 10 21 (L4) 1.832,1.635 1.654,0.951 false

Disconnect the ECM connector.


b.

Disconnect the A27 4 wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A38-21 (L4) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A52-21 (L4) - Body ground Always 10 kΩ or higher



Text in Illustration
*1 for LHD
*2 for RHD
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR