Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255273 AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)  P0751  Shift Solenoid "A" Performance (Shift Solenoid Valve S1)  


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).

DTC Code DTC Detection Condition Trouble Area
P0751

S1 stuck ON malfunction*1:

The ECM determines there is a malfunction when the following conditions are both met. (2 trip detection logic*3, 1 trip detection logic*4)


(a) When the ECM directs the transmission to switch to 1st gear, the actual gear is shifted to 2nd.
(b) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th.
·

Shift solenoid valve S1 remains closed

·

Valve body is blocked

·

Automatic transmission (clutch, brake, gear, etc.)


P0751

S1 stuck OFF malfunction*2:

The ECM determines there is a malfunction when conditions (a) and (b) are met. (2 trip detection logic*3, 1 trip detection logic*4)


(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is also shifted to 5th.
(b) When the ECM directs the transmission to switch to 6th gear, the engine overruns (clutch slips).
·

Shift solenoid valve S1 remains open

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked

·

No. 2 brake malfunction (Driving is difficult.)

·

Automatic transmission (clutch, brake, gear, etc.)



*3: w/ OBD

*4: w/o OBD


HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM command gearshift 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under S1 stuck ON malfunction 2nd 2nd 3rd 4th 5th 6th
*2: Actual gear position under S1 stuck OFF malfunction 1st 1st 3rd 4th 5th N*

N*: Neutral

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under fail-safe mode when S1 stuck ON malfunction 2nd 2nd 3rd 4th 5th 6th
*2: Actual gear position under fail-safe mode when S1 stuck OFF malfunction 1st* 1st* 3rd 3rd 3rd 3rd

*: Under engine braking, downshifting to 1st or 2nd gear is prohibited.



MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of shift solenoid valve S1.

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the GTS.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1UR-FE)>FAIL-SAFE CHART).


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valves and set each shift position by yourself
·

Press "→" button: Shift up


·

Press "←" button: Shift down


Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (30 mph) or less

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (30 mph) or less.

·

The 4th to 5th and 5th to 6th up-shift must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the GTS.

·

Shift solenoid valve S1 turns ON/OFF normally when the shift lever is in D.

ECM command gearshift 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S1 OFF ON ON ON ON ON





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0751)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the GTS.

Result
Result Proceed to
Only P0751 is output A
P0751 and other DTCs are output B

HINT:

If any other codes besides P0751 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

OK

3.INSPECT SHIFT SOLENOID VALVE S1

NG

3.INSPECT SHIFT SOLENOID VALVE S1
a.
C209925E04
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 2.413,0.126 2.664,0.328 0.251,0.202 10 (+) 1.695,0.126 1.900,0.328 0.206,0.202 10 (-)

Remove the shift solenoid valve S1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S1 connector

·

Battery negative (-) → Shift solenoid valve S1 body


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve S1)


OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on each valve.




OK

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY