Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255274 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF)  P0766  Shift Solenoid "D" Performance (Shift Solenoid Valve S4)  P0776  Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2)  


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th, 5th or 6th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems with the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC Code DTC Detection Condition Trouble Area
P0766 A shift solenoid valve S4 stuck OFF malfunction or brake control valve malfunction*1:
Shifting to 5th and 6th gears is impossible.
The ECM determines there is a malfunction when the following conditions are both met (2 trip detection logic).
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·

Shift solenoid valve S4 remains closed

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked (brake control valve)

·

Automatic transmission (clutch, brake or gear, etc.)


P0776 A shift solenoid valve SL2 stuck ON malfunction or brake control valve malfunction*1:
Shifting to 5th and 6th gears is impossible.
The ECM determines there is a malfunction when the following conditions are both met (2 trip detection logic).
(a) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 4th.
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th.
·

Shift solenoid valve SL2 remains open

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked (brake control valve)

·

Automatic transmission (clutch, brake or gear, etc.)



HINT:
·

Gear positions in the event of a solenoid valve mechanical problem:

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under malfunction 1st 2nd 3rd 4th 4th 4th

·

Gear position during fail-safe operation:

If any malfunction is detected, the ECM changes into the fail-safe mode to shift into the gear positions as shown in the table below.

Gear position under normal conditions 1st 2nd 3rd 4th 5th 6th
*1: Actual gear position under fail-safe mode 1st 2nd 3rd 3rd 3rd 3rd



MONITOR DESCRIPTION

This DTC indicates "stuck OFF malfunction" of the shift solenoid valve S4, "stuck ON malfunction" of the shift solenoid valve SL2, or brake control valve malfunction. The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the GTS.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF)>FAIL-SAFE CHART).


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valve and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th and 5th to 6th up-shifts must be performed with the accelerator pedal released.

·

The 6th to 5th and 5th to 4th down-shifts must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the GTS.

·

The shift solenoid valve SL2 turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve S4 OFF OFF OFF OFF ON ON
Shift solenoid valve SL2 ON ON ON ON OFF OFF





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0766 AND P0776)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs using the GTS.

Result
Result Proceed to
P0766 and/or P0776 is output A
P0766, P0776 and other DTCs are output B

HINT:

If any other codes besides P0766 and P0776 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING GTS (SHIFT SOLENOID VALVE SLT)

OK

3.INSPECT SHIFT SOLENOID VALVE S4

NG

3.INSPECT SHIFT SOLENOID VALVE S4
a.
C208651E04
0.058,0.004 0.374,0.206 0.317,0.202 10 *a 2.384,0.123 2.635,0.325 0.251,0.202 10 (+) 1.666,0.123 1.871,0.325 0.206,0.202 10 (-)

Remove the shift solenoid valve S4.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve S4 connector terminal - Shift solenoid valve S4 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve S4 connector

·

Battery negative (-) → Shift solenoid valve S4 body


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve S4)


OK

4.INSPECT SHIFT SOLENOID VALVE SL2

NG

4.INSPECT SHIFT SOLENOID VALVE SL2
a.
C197715E12
0.057,0.006 0.374,0.208 0.317,0.202 10 *a 1.757,0.95 2.207,0.362 false 2.238,0.195 2.402,0.397 0.164,0.202 10 1 1.506,0.95 1.056,0.362 false 0.918,0.195 1.082,0.397 0.164,0.202 10 2 1.757,2.946 2.207,2.359 false 2.238,2.192 2.402,2.394 0.164,0.202 10 1 1.506,2.946 1.056,2.359 false 0.918,2.192 1.082,2.394 0.164,0.202 10 2 1.923,3.929 2.147,4.131 0.224,0.202 10 (+) 1.162,3.929 1.386,4.131 0.224,0.202 10 (-)

Remove the shift solenoid valve SL2.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Text in Illustration
*a Component without harness connected
(Shift Solenoid Valve SL2)


OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG