Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) › from 2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255274 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV with DPF)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd mode is selected with the ECT 2nd switch, the ECM controls the solenoid valves and the transmission starts from 2nd gear.

The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.

When the shift lever is in D, the transmission automatically shifts up through 3rd to 6th as usual.

CAUTION / NOTICE / HINT

When the ECT 2nd switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the ECT 2nd switch once again.

HINT:

2nd mode is automatically canceled when the ignition switch is turned off.


PROCEDURE

1.DRIVING TEST
HINT:

The driving test should be performed on a paved road (nonskid road).


a.

Start the engine.


b.

Turn the ECT 2nd switch off (normal drive mode).


c.

Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.


d.

Turn the ECT 2nd switch on and perform the same check as above.

When driving the vehicle with the ECT 2nd switch on and off, check that there is a difference in acceleration.

OK:

There is a difference in acceleration.




OK

NG

2.INSPECT ECT 2ND SWITCH
2.INSPECT ECT 2ND SWITCH
a.
C331266E09
0.062,0 0.260,0.198 0.198,0.198 10 *a 0.286,0.604 0.429,0.789 0.143,0.185 10 E 1.225,1.055 0.662,0.686 0.662,0.686 0.447,0.686 false 2.835,1.673 3.166,1.859 0.331,0.185 10 2ND 1.724,1.401 2.603,1.754 2.603,1.754 2.801,1.754 false

w/ Entry and Start System:

Remove the integration control and panel assembly (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/ Entry and Start System)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (2ND) - 5 (E) ECT 2nd switch on Below 1 Ω
8 (2ND) - 5 (E) ECT 2nd switch off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Integration Control and Panel Assembly)

c.
C238423E14
0.049,0 0.245,0.202 0.195,0.202 10 *a 0.574,1.762 0.869,1.964 0.295,0.202 10 E 0.688,1.743 1.053,1.286 false 1.871,1.762 2.360,1.964 0.489,0.202 10 2ND 1.992,1.743 1.499,1.286 false

w/o Entry and Start System:

Remove the suspension control switch (See page Drivetrain>AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>COMBINATION SWITCH(w/o Entry and Start System)>REMOVAL).


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
17 (2ND) - 20 (E) ECT 2nd switch on Below 1 Ω
17 (2ND) - 20 (E) ECT 2nd switch off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Suspension Control Switch)

Result
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


A

3.CHECK HARNESS AND CONNECTOR (ECT 2ND SWITCH - BODY GROUND)

B

C

3.CHECK HARNESS AND CONNECTOR (ECT 2ND SWITCH - BODY GROUND)
a.
U165550E02
2.604,0.708 2.021,0.99 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.698,0.604 2.906,0.792 0.208,0.188 10 false E 0.521,0.865 0.875,1.042 0.354,0.177 10 false V9

w/ Entry and Start System:

Disconnect the integration control and panel assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V9-5 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Integration Control and Panel Assembly)

c.
U165083E01
2.519,1.704 2.376,1.389 false 2.494,1.704 2.768,1.906 0.274,0.202 10 E 0.057,0.005 0.252,0.207 0.195,0.202 10 *a 0.334,0.979 0.709,1.212 0.375,0.233 10 V4

w/o Entry and Start System:

Disconnect the suspension control switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-20 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)


OK

4.CHECK HARNESS AND CONNECTOR (ECT 2ND SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECT 2ND SWITCH - ECM)
a.
U164947E01
0.058,0.002 0.375,0.204 0.317,0.202 10 *a 1.071,0.22 1.373,0.453 0.302,0.233 10 A38 1.479,0.22 1.680,0.453 0.201,0.233 10 *A 2.008,0.22 2.310,0.453 0.302,0.233 10 A52 2.416,0.22 2.617,0.453 0.201,0.233 10 *B 2.037,1.674 2.713,1.876 0.676,0.202 10 17 (SNWI) 2.385,1.648 2.197,0.881 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
A38-17 (SNWI) - Body ground ECT 2nd switch on Below 1 Ω
A38-17 (SNWI) - Body ground ECT 2nd switch off 10 kΩ or higher

for RHD
Tester Connection Switch Condition Specified Condition
A52-17 (SNWI) - Body ground ECT 2nd switch on Below 1 Ω
A52-17 (SNWI) - Body ground ECT 2nd switch off 10 kΩ or higher



Text in Illustration
A for LHD
B for RHD
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR