Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2015.08–2017.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.

DTC Code DTC Detection Condition Trouble Area
P0705 When one of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

P input signal

·

N input signal

·

R input signal

·

D input signal


(B) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic).
·

NSW input signal

·

R input signal

·

D input signal


(C) Any of the following signals are ON for 2.0 sec. or more when the shift lever is in S (2 trip detection logic).
·

NSW input signal

·

P input signal

·

N input signal

·

R input signal


(D) All the signals are OFF simultaneously for the P, R, N and D positions (2 trip detection logic).
·

Park/neutral position switch

·

Transmission control switch (Transmission floor shift assembly)

·

Open or short in park/neutral position switch circuit

·

ECM



MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D or S).

The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C257148E29
5.792,6.427 6.177,6.625 0.385,0.198 10 false ECM 4.302,1.917 5.135,2.115 0.833,0.198 10 false to ST Relay 0.021,1.844 1.896,2.229 1.875,0.385 10 false from Certification ECU (Smart Key ECU Assembly) (STAR) 5.26,5.76 5.573,5.958 0.313,0.198 10 false A38 5.615,5.76 5.781,5.958 0.167,0.198 10 false S 5.302,5.563 5.521,5.76 0.219,0.198 10 false 25 5.26,4.177 5.573,4.375 0.313,0.198 10 false C45 5.635,4.167 5.948,4.365 0.313,0.198 10 false P 5.333,3.969 5.49,4.167 0.156,0.198 10 false 2 5.26,3.573 5.573,3.771 0.313,0.198 10 false C45 5.625,3.563 5.802,3.76 0.177,0.198 10 false R 5.292,3.375 5.51,3.573 0.219,0.198 10 false 26 5.26,2.969 5.573,3.167 0.313,0.198 10 false C45 5.625,2.958 5.802,3.146 0.177,0.188 10 false N 5.302,2.792 5.521,2.99 0.219,0.198 10 false 25 5.25,2.375 5.563,2.573 0.313,0.198 10 false C45 5.625,2.365 5.802,2.563 0.177,0.198 10 false D 5.313,2.188 5.531,2.385 0.219,0.198 10 false 27 5.26,1.198 5.573,1.396 0.313,0.198 10 false C45 5.615,1.198 6.031,1.396 0.417,0.198 10 false NSW 5.26,1 5.531,1.198 0.271,0.198 10 false 120 3.76,2.042 3.979,2.24 0.219,0.198 10 false 5 3.771,2.5 3.99,2.698 0.219,0.198 10 false 7 3.771,3.083 3.99,3.281 0.219,0.198 10 false 9 3.771,4.302 3.99,4.5 0.219,0.198 10 false 6 3.76,3.688 3.979,3.885 0.219,0.198 10 false 1 3.76,5.865 3.979,6.063 0.219,0.198 10 false 7 3.573,1.813 3.792,2.01 0.219,0.198 10 false L 3.479,2.26 3.75,2.458 0.271,0.198 10 false DL 3.49,2.865 3.76,3.063 0.271,0.198 10 false NL 2.76,3.167 3.031,3.365 0.271,0.198 10 false RB 3.5,3.469 3.771,3.667 0.271,0.198 10 false RL 3.5,4.073 3.771,4.271 0.271,0.198 10 false PL 3.552,5.646 3.823,5.844 0.271,0.198 10 false S 2.76,1.813 2.979,2.01 0.219,0.198 10 false B 2.781,5.646 3.052,5.844 0.271,0.198 10 false IG 2.573,2.042 2.792,2.24 0.219,0.198 10 false 4 2.563,3.406 2.781,3.604 0.219,0.198 10 false 2 2.573,5.875 2.844,6.073 0.271,0.198 10 false 3 2.375,6.219 2.688,6.417 0.313,0.198 10 false E52 2.375,6.406 4.229,6.604 1.854,0.198 10 false Transmission Control Switch 0.271,5.75 2.177,5.948 1.906,0.198 10 false from ECU-IG NO. 2 Fuse 0.521,3.271 1.875,3.469 1.354,0.198 10 false from BKUP LP Fuse 2.292,4.667 2.604,4.865 0.313,0.198 10 false C24 2.292,4.844 4.115,5.042 1.823,0.198 10 false Park/Neutral Position Switch

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status/
ON or OFF
Shift lever:
·

In P or N: ON

·

Not in P or N: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range) PNP switch status/
ON or OFF
Shift lever:
·

In P: ON

·

Not in P: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status/
ON or OFF
Shift lever:
·

In R: ON

·

Not in R: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range) PNP switch status/
ON or OFF
Shift lever:
·

In N: ON

·

Not in N: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Sports Shift Up SW Sport shift up switch status/
ON or OFF
·

ON: Shift lever held in "+" (up-shift)

·

OFF: Shift lever not in "+" (up-shift)


-
Sports Shift Down SW Sport shift down switch status/
ON or OFF
·

ON: Shift lever held in "-" (down-shift)

·

OFF: Shift lever not in "-" (down-shift)


-
Sports Mode Selection SW Sport mode select switch status/
ON or OFF
Shift lever position is:
·

ON: In S, "+" and "-"

·

OFF: Not in S, "+" and "-"


-
Shift SW Status (D Range) PNP switch status/
ON or OFF
Shift lever:
·

In D: ON

·

Not in D: OFF


When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
U164954E02
1.802,1.01 2.177,0.323 false 0.365,1.042 0.74,1.271 0.375,0.229 10 false C24 2.229,0.229 2.542,0.427 0.313,0.198 10 false RB 0.052,0 0.365,0.198 0.313,0.198 10 false *a

Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-2 (RB) - Body ground Engine switch on (IG) 11 to 14 V
C24-2 (RB) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
U164955E02
2.115,1.021 2.385,0.333 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.448,0.24 2.76,0.438 0.313,0.198 10 false B 0.375,1.042 0.75,1.271 0.375,0.229 10 false C24

Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-4 (B) - Body ground Engine switch on (IG) 11 to 14 V
C24-4 (B) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E90
1.833,0.958 2.208,0.417 false 1.271,0.969 0.896,0.427 false 2.083,1.281 2.448,1.823 false 0.969,1.813 1.344,1.271 false 1.594,0.958 1.51,0.417 false 2.042,1.823 1.958,1.281 false 1.625,1.823 1.708,1.281 false 2.271,0.323 2.583,0.521 0.313,0.198 10 false RL 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.781,0.313 1.094,0.51 0.313,0.198 10 false B 2.521,1.75 2.833,1.948 0.313,0.198 10 false L 0.771,1.76 1.083,1.958 0.313,0.198 10 false NL 1.292,0.333 1.604,0.531 0.313,0.198 10 false RB 2.104,1.75 2.417,1.948 0.313,0.198 10 false PL 1.438,1.76 1.75,1.958 0.313,0.198 10 false DL

Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever in N Below 1 Ω
2 (RB) - 7 (DL)
·

Shift lever in D

·

Shift lever in S, "+" or "-"


Below 1 Ω
·

2 (RB) - 6 (PL)

·

4 (B) - 5 (L)


Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
·

2 (RB) - 9 (NL)

·

4 (B) - 5 (L)


Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL)
·

Shift lever not in D

·

Shift lever not in S, "+" or "-"


10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch)



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
U164956E02
1.802,1.063 2.344,0.75 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 2.406,0.656 2.719,0.854 0.313,0.198 10 false IG 0.542,1 0.917,1.229 0.375,0.229 10 false E52

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E52-3 (IG) - Body ground Engine switch on (IG) 11 to 14 V
E52-3 (IG) - Body ground Engine switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control Switch)



OK

5.INSPECT TRANSMISSION CONTROL SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH
a.
C203344E38
1.635,0.74 1.104,0.302 false 1.115,1.417 1.646,0.99 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 0.896,0.219 1.135,0.417 0.24,0.198 10 false IG 0.958,1.396 1.146,1.594 0.188,0.198 10 false S

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG) - 7 (S) Shift lever in S, "+" or "-" Below 1 Ω
3 (IG) - 7 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transmission Control Switch)



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
U165268E02
2.302,1.958 1.979,1.208 false 0.708,4.365 0.573,3.177 false 1.073,4.063 0.656,3.177 false 1.719,4.365 0.74,3.177 false 0.292,4.042 0.563,3.073 false 1.448,2.479 1.823,2.708 0.375,0.229 10 false C45 0.104,0.031 0.302,0.229 0.198,0.198 10 false *a 2.167,2 2.604,2.198 0.438,0.198 10 false 25 (S) 1.698,0.427 2.073,0.656 0.375,0.229 10 false A38 1.583,4.396 2.031,4.594 0.448,0.198 10 false 27 (D) 0.094,4.073 0.458,4.271 0.365,0.198 10 false 2 (P) 0.552,4.406 1,4.604 0.448,0.198 10 false 25 (N) 0.927,4.083 1.375,4.281 0.448,0.198 10 false 26 (R)

a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C45-2 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever in P


11 to 14 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever in R


11 to 14 V*
C45-25 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever in N


11 to 14 V
C45-27 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever in D


11 to 14 V
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in S, "+" or "-"


11 to 14 V
C45-2 (P) - Body ground
·

Engine switch on (IG)

·

Shift lever not in P


Below 1 V
C45-26 (R) - Body ground
·

Engine switch on (IG)

·

Shift lever not in R


Below 1 V
C45-25 (N) - Body ground
·

Engine switch on (IG)

·

Shift lever not in N


Below 1 V
C45-27 (D) - Body ground
·

Engine switch on (IG)

·

Shift lever not in D


Below 1 V
A38-25 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in S, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to the turning on of the back-up light.



Text in Illustration
*a Front view of wire harness connector
(to ECM)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C24 park/neutral position switch connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (B) - C45-120 (NSW) Always Below 1 Ω
C24-4 (B) or C45-120 (NSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR