Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P2772  Four Wheel Drive (4WD) Low Switch Circuit Range / Performance  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains on.

DTC Code DTC Detection Condition Trouble Area
P2772 The transfer L4 position switch remains on while the vehicle is running under the following conditions for 1.8 sec. or more (1 trip detection logic):
(a) The output shaft speed is between 1000 and 3000 rpm.
(b) The transfer position switch is in H4.
·

Short in transfer L4 position switch circuit

·

Four wheel drive control ECU

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer-case L4 position switch to determine when the transfer-case L4 gears are engaged. If the L4 switch indicates that the transfer-case L4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The transfer-case shifter is in the "H4" position.

·

The transfer-case output shaft rpm is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


WIRING DIAGRAM

C160106E24
5.198,1.323 5.427,1.49 0.229,0.167 10 false 21 5.51,1.208 5.938,1.406 0.427,0.198 10 false L4 1.854,1.333 2.083,1.5 0.229,0.167 10 false 21 1.51,1.219 1.75,1.417 0.24,0.198 10 false L4 1.854,1.99 2.083,2.156 0.229,0.167 10 false 16 1.51,1.885 1.75,2.083 0.24,0.198 10 false NP 1.771,3.563 1.917,3.729 0.146,0.167 10 false 3 1.531,3.458 1.708,3.656 0.177,0.198 10 false N 5.25,3.573 5.479,3.74 0.229,0.167 10 false 5 5.51,3.469 5.938,3.667 0.427,0.198 10 false TFN 5.688,4.167 5.99,4.333 0.302,0.167 10 false A38 5.667,4.333 6.094,4.531 0.427,0.198 10 false ECM 0.385,4.042 2.51,4.24 2.125,0.198 10 false Transfer Shift Actuator Assembly 0.385,3.854 0.813,4.052 0.427,0.198 10 false C38 0.385,2.667 2.365,2.865 1.979,0.198 10 false Four Wheel Drive Control ECU 0.385,2.479 0.813,2.677 0.427,0.198 10 false A27

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U164966E02
0.323,1.781 0.521,1.313 false 0.052,0 0.365,0.198 0.313,0.198 10 false *a 1.583,0.25 1.958,0.479 0.375,0.229 10 false A27 0.219,1.813 0.469,2.01 0.25,0.198 10 false L4

Disconnect the four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Four Wheel Drive Control ECU)



OK

GO TO TRANSFER SYSTEM INSPECTION

NG

2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
a.
U165069E02
1.813,1.677 1.635,0.99 false 1.677,0.302 2.052,0.531 0.375,0.229 10 false A38 0.115,0.073 0.313,0.271 0.198,0.198 10 false *a 1.635,1.719 2.167,1.917 0.531,0.198 10 false 21 (L4)

Disconnect the ECM connector.


b.

Disconnect the A27 four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR