Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) J

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  Pattern Select Switch 2nd Start Mode Circuit  


DESCRIPTION

When 2nd mode is selected with the pattern select (2ND) switch, the ECM controls the solenoid valves and the transmission starts from 2nd gear.

The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.

When the shift lever is in D, the transmission automatically shifts up through 3rd to 5th as usual.

CAUTION / NOTICE / HINT

When the pattern select (2ND) switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the pattern select (2ND) switch once again.

HINT:

2nd mode is automatically canceled when the engine switch is turned off.


PROCEDURE

1.DRIVING TEST
HINT:

The driving test should be performed on a paved road (nonskid road).


a.

Start the engine.


b.

Turn the 2ND switch off (normal drive mode).


c.

Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.


d.

Turn the 2ND switch on and perform the same check as above.

When driving the vehicle with the 2ND switch on and off, check that there is a difference in acceleration.

OK:

There is a difference in acceleration.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PATTERN SELECT (2ND) SWITCH
2.INSPECT PATTERN SELECT (2ND) SWITCH
a.
C238423E16
1.656,1.771 1.5,1.313 false 0.917,1.781 1.052,1.323 false 1.542,1.781 1.875,1.979 0.333,0.198 10 false 2ND 0.052,0 0.25,0.198 0.198,0.198 10 false *a 0.802,1.781 0.969,1.979 0.167,0.198 10 false E

Remove the suspension control switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>CRAWL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
17 (2ND) - 20 (E) Pattern select (2ND) switch continuously pressed Below 1 Ω
17 (2ND) - 20 (E) Pattern select (2ND) switch released 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Suspension Control Switch)



OK

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)

NG

REPLACE PATTERN SELECT (2ND) SWITCH (SUSPENSION CONTROL SWITCH)

3.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)
a.
U165078E03
2.521,1.719 2.375,1.396 false 2.521,1.74 2.688,1.938 0.167,0.198 10 false E 0.052,0 0.25,0.198 0.198,0.198 10 false *a 0.354,1.031 0.729,1.26 0.375,0.229 10 false V4

Disconnect the suspension control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V4-20 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Suspension Control Switch)



OK

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)
U164949E02
1.542,1.688 1.813,0.865 false 0.063,0 0.375,0.198 0.313,0.198 10 false *a 1.125,1.719 1.844,1.917 0.719,0.198 10 false 4 (SNWI) 1.677,0.271 2.052,0.5 0.375,0.229 10 false A38

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A38-4 (SNWI) - Body ground Pattern select (2ND) switch continuously pressed Below 1 Ω
A38-4 (SNWI) - Body ground Pattern select (2ND) switch released 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR