Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255293 PARK / NEUTRAL POSITION SWITCH A

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.


a.

Install the park/neutral position switch assembly to the manual valve lever shaft.


b.
C329052

Temporarily install the park/neutral position switch assembly with the 2 bolts.

HINT:

Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.



c.

Install the lock washer and the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


d.

Install the No. 1 shift lever bush to the transmission control shaft lever.


e.

Install the bush to the transmission control shaft lever.


f.
C329050

Temporarily install the transmission control shaft lever.


g.
C329054E04
0.76,0.302 0.906,0.458 0.146,0.156 10 false P 1.292,0.26 1.438,0.417 0.146,0.156 10 false R 1.708,0.229 1.854,0.385 0.146,0.156 10 false N

Turn the transmission control shaft lever counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


h.

Remove the transmission control shaft lever.


i.
C329053E01
2.496,0.363 2.685,0.551 0.188,0.188 10 *a 2.902,1.317 3.090,1.505 0.188,0.188 10 *b 2.484,0.458 2.292,0.458 2.292,0.458 1.656,0.851 false 1.666,1.406 2.884,1.406 false

Align the groove with the neutral basic line.

Text in Illustration
*a Neutral Basic line
*b Groove


j.
C329052

Hold the park/neutral position switch assembly in the position described above and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


k.
C329051E02
1.874,1.099 1.37,0.715 1.37,0.715 1.135,0.715 false 0.822,0.614 1.020,0.803 0.198,0.188 10 *a

Using a screwdriver, bend the tabs of the lock washer.

Text in Illustration
*a Protective Tape


l.
C329050

Install the transmission control shaft lever with the spring washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


m.

Connect the switch connector.


Hide 33702B 2.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

a.
C329055

Connect the floor shift gear shifting rod sub-assembly to the transmission control shaft lever with the pin.


b.

Install a new clip.


Hide 58155 5.INSTALL NO. 3 FRONT FLOOR HEAT INSULATOR

a.

Install the No. 3 front floor heat insulator with the 4 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 7.INSPECT FOR EXHAUST GAS LEAK