Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2015.08–2017.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0705
1.

Battery voltage is 9.5 V or higher.

2.

No signal of the A, B, C and PA signals.

3.

5 seconds or more

4.

2-trip detection logic


·

Transmission floor shift assembly (incorrect adjustment)

·

Park/neutral position switch assembly (incorrect adjustment)

·

Park/neutral position switch assembly

·

Open or short in park/neutral position switch assembly circuit

·

TCM


1.

Battery voltage is 9.5 V or higher.

2.

Implausible combination of the A, B, C and PA signals.

3.

5 seconds or more

4.

2-trip detection logic


1.

Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm and vehicle speed is 30 km/h (18.6 mph) or more.

2.

Uncertain D position combination of the A, B, C and PA signals.

3.

30 seconds or more

4.

2-trip detection logic



HINT:
Park/neutral position switch normal operation chart:
Shift Lever Position A switch B switch C switch PA switch
P ON OFF OFF ON
R ON ON OFF OFF
N OFF ON OFF ON
D OFF ON ON OFF

Park/neutral position switch malfunction operation chart:
Malfunction Status A switch B switch C switch PA switch
No signal OFF OFF OFF OFF
Implausible combination ON ON OFF ON
ON ON ON ON
ON OFF ON ON
ON OFF ON OFF
OFF OFF ON ON
OFF OFF OFF ON
ON OFF OFF OFF
OFF OFF ON OFF
ON ON ON OFF
OFF ON OFF OFF
Uncertain D position OFF ON ON ON


MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the TCM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends signals to the TCM according to the shift lever position (P, N, R or D).

The TCM determines that there is a problem with the switch or related parts if a malfunction occurs in the park/neutral position switch signal. The TCM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C345838E02
5.751,4.911 6.203,5.087 0.451,0.176 10 TCM 5.751,4.751 6.203,4.926 0.451,0.176 10 A82 5.329,1.515 5.780,1.691 0.452,0.176 10 PA 5.327,2.116 5.778,2.292 0.451,0.176 10 A 5.323,2.716 5.775,2.892 0.451,0.176 10 B 5.325,3.317 5.777,3.493 0.452,0.176 10 C 3.628,1.515 4.079,1.691 0.451,0.176 10 PA 4.277,1.013 5.211,1.189 0.934,0.176 10 to ST Relay 0.31,2.221 1.740,2.863 1.430,0.643 10 from Certification ECU (Smart Key ECU Assembly) (STAR) 0.601,1.013 1.918,1.241 1.317,0.228 10 from ECM (NSW) 3.713,2.116 4.164,2.292 0.452,0.176 10 A 3.709,2.716 4.161,2.892 0.452,0.176 10 B 3.711,3.317 4.162,3.493 0.451,0.176 10 C 5.043,1.515 5.495,1.691 0.452,0.176 10 16 5.041,2.116 5.493,2.292 0.451,0.176 10 26 5.037,2.716 5.489,2.892 0.451,0.176 10 17 5.115,3.317 5.566,3.493 0.451,0.176 10 6 3.943,1.515 4.395,1.691 0.451,0.176 10 7 3.941,2.116 4.393,2.292 0.452,0.176 10 5 3.937,2.716 4.389,2.892 0.452,0.176 10 9 3.943,3.317 4.395,3.493 0.452,0.176 10 4 0.41,4.017 1.910,4.193 1.500,0.176 10 from BKUP LP Fuse 0.102,3.422 1.893,3.597 1.792,0.176 10 from ECU-IG NO. 2 Fuse 2.629,3.317 3.080,3.493 0.452,0.176 10 IG 2.419,3.317 2.631,3.493 0.212,0.176 10 6 2.029,4.495 2.481,4.671 0.452,0.176 10 C24 2.029,4.655 4.638,4.831 2.609,0.176 10 Park/Neutral Position Switch Assembly 2.621,3.913 3.073,4.089 0.452,0.176 10 RB 2.411,3.913 2.623,4.089 0.212,0.176 10 1 3.627,3.913 4.078,4.089 0.451,0.176 10 RL 3.943,3.913 4.395,4.089 0.452,0.176 10 2 5.325,3.913 5.777,4.089 0.452,0.176 10 R 5.11,3.913 5.322,4.089 0.212,0.176 10 5 3.728,0.913 3.915,1.089 0.188,0.176 10 L 2.629,0.913 2.816,1.089 0.188,0.176 10 B 3.943,0.913 4.395,1.089 0.451,0.176 10 8 2.413,0.913 2.864,1.089 0.451,0.176 10 3

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the engine switch on (IG).*1

2.

Wait with the shift lever in each position (P, R, N and D) for 5 seconds or more.*2

3.

Drive the vehicle 30 km/h (19 mph) or more for 30 seconds or more.*3

4.

Turn the engine switch off.

5.

Perform steps (*1) through (*3) again.



PROCEDURE

1.ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.


NEXT

2.ADJUST TRANSMISSION FLOOR SHIFT ASSEMBLY
2.ADJUST TRANSMISSION FLOOR SHIFT ASSEMBLY
a.

Adjust the transmission floor shift assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LEVER>ADJUSTMENT).



NEXT

3.READ VALUE USING GTS (SHIFT SW STATUS)
3.READ VALUE USING GTS (SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

According to the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (P Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever is in P

·

OFF: Shift lever is not in P


When shift lever position displayed on the GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever is in R

·

OFF: Shift lever is not in R


When shift lever position displayed on the GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever is in N

·

OFF: Shift lever is not in N


When shift lever position displayed on the GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status/
ON or OFF
·

ON: Shift lever is in D or S

·

OFF: Shift lever is not in D or S


When shift lever position displayed on the GTS differs from actual position, adjustment of park/neutral position switch assembly or shift cable may be incorrect.

Result
Result Proceed to
Data List value is not within the normal condition A
Data List value is within the normal condition B



A

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)

B

INCORRECT ADJUSTMENT

4.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U165582E02
1.219,1.802 1.479,1.281 false 0.375,1.042 0.802,1.24 0.427,0.198 10 false C24 0.125,0.073 0.552,0.271 0.427,0.198 10 false *a 1.042,1.729 1.469,1.927 0.427,0.198 10 false IG

Disconnect the park/neutral position switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E98
1.896,0.969 2.271,0.427 false 0.99,1.781 1.354,1.281 false 1.375,0.948 1.052,0.406 false 2.219,1.781 1.979,1.271 false 1.635,1.781 1.729,1.281 false 1.25,0.948 0.927,0.406 false 2.344,1.781 2.104,1.271 false 2.26,0.25 2.573,0.448 0.313,0.198 10 false RB 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 0.823,1.75 1.031,1.948 0.208,0.198 10 false B 0.75,0.313 1.063,0.51 0.313,0.198 10 false C 2.198,1.823 2.51,2.021 0.313,0.198 10 false IG 1.51,1.792 1.729,1.99 0.219,0.198 10 false PA 2.427,1.781 2.74,1.979 0.313,0.198 10 false A 0.969,0.24 1.281,0.438 0.313,0.198 10 false B

Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (IG) - 4 (C) Shift lever in D and S Below 1 Ω
6 (IG) - 5 (A) Shift lever in P and R Below 1 Ω
6 (IG) - 7 (PA) Shift lever in P and N Below 1 Ω
6 (IG) - 9 (B) Shift lever in R, N, D and S Below 1 Ω
6 (IG) - 4 (C) Shift lever not in D and S 10 kΩ or higher
6 (IG) - 5 (A) Shift lever not in P and R 10 kΩ or higher
6 (IG) - 7 (PA) Shift lever not in P and N 10 kΩ or higher
6 (IG) - 9 (B) Shift lever not in R, N, D and S 10 kΩ or higher
1 (RB) - 4 (C), 5 (A), 7 (PA) and 9 (B) Shift lever in P, R, N, D and S 10 kΩ or higher
3 (B) - 4 (C), 5 (A), 7 (PA) and 9 (B) Shift lever in P, R, N, D and S 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)
a.

Disconnect the C24 park/neutral position switch assembly connector.


b.

Disconnect the A82 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-4 (C) - A82-6 (C) Always Below 1 Ω
C24-5 (A) - A82-26 (A) Always Below 1 Ω
C24-7 (PA) - A82-16 (PA) Always Below 1 Ω
C24-9 (B) - A82-17 (B) Always Below 1 Ω
C24-4 (C) or A82-6 (C) - Body ground Always 10 kΩ or higher
C24-5 (A) or A82-26 (A) - Body ground Always 10 kΩ or higher
C24-7 (PA) or A82-16 (PA) - Body ground Always 10 kΩ or higher
C24-9 (B) or A82-17 (B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR