Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0717  Input/Turbine Speed Sensor "A" Circuit No Signal  P07BF  Input/Turbine Speed Sensor "A" Circuit Low  P07C0  Input/Turbine Speed Sensor "A" Circuit High  


DESCRIPTION

The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the TCM.

Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (SP2) signals, the TCM controls engine torque and shift timing. Based on the input shaft rotation speed and the engine speed signal, lock-up control is performed.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0717
1.

Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, output speed is 300 rpm or more and number of output speed sensor signal pulse is 30 times.

2.

Transmission revolution sensor (NT) signal is no signal

3.

Malfunction status occurs 100 times per trip

4.

1-trip detection logic


·

Harness or connector

·

Transmission wire

·

Transmission revolution sensor (NT)

·

TCM


P07BF
1.

Battery voltage is 9.5 V or higher.

2.

Transmission revolution sensor (NT) input voltage is below 0.2199 V.

3.

0.5 seconds

4.

1-trip detection logic


P07C0
1.

Battery voltage is 9.5 V or higher.

2.

Transmission revolution sensor (NT) input voltage is higher than 2.6637 V.

3.

0.5 seconds

4.

1-trip detection logic



MONITOR DESCRIPTION

The transmission revolution sensor (NT) detects the input shaft speed. The TCM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (SP2).

If the TCM detects no signal from the transmission revolution sensor (NT) even while the vehicle is moving, it will conclude that is a malfunction of the transmission revolution sensor (NT). The TCM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C343211E11
5.146,1.094 5.656,1.292 0.51,0.198 10 false NTB 4.927,1.094 5.438,1.292 0.51,0.198 10 false 7 3.135,1.094 3.646,1.292 0.51,0.198 10 false 17 2.729,1.094 3.24,1.292 0.51,0.198 10 false NTB 0.563,1.396 0.781,1.594 0.219,0.198 10 false 1 0.573,2.219 0.792,2.417 0.219,0.198 10 false 2 4.938,2.219 5.448,2.417 0.51,0.198 10 false 8 3.125,2.219 3.635,2.417 0.51,0.198 10 false 18 2.719,2.219 3.229,2.417 0.51,0.198 10 false NTO 1.073,2.927 1.583,3.125 0.51,0.198 10 false C171 1.073,3.115 2.917,3.313 1.844,0.198 10 false Transmission Wire 1.031,1.677 2.604,2.063 1.573,0.385 10 false Transmission Revolution Sensor (NT) 5.146,2.219 5.656,2.417 0.51,0.198 10 false NTO 5.417,3.188 5.927,3.385 0.51,0.198 10 false A81 5.406,3.385 5.917,3.583 0.51,0.198 10 false TCM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List / SPD (NT).


g.

According to the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm.

HINT:
·

SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

·

SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS (SPD (NT) AND NT SENSOR VOLTAGE)
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / ECT / Data List / SPD (NT), NT Sensor Voltage.


f.

According to the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SPD (NT) Input shaft speed/
Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm.
NT Sensor Voltage NT sensor voltage/
Min.: 0 V
Max.: 5 V
·

1.182 to 1.622 V: High current

·

0.391 to 0.814 V: Low current


-

Result
Result Proceed to
Data List value is not within the normal condition A
Data List value is within the normal condition B



A

2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)

B

2.CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NT TERMINAL)
a.
U164961E02
1.583,1.708 1.844,1.24 true 2.198,1.708 1.948,1.24 true 1.531,0.229 1.906,0.458 0.375,0.229 10 false C171 1.417,1.708 1.844,1.906 0.427,0.198 10 false NTB 2.094,1.729 2.521,1.927 0.427,0.198 10 false NTO 0.125,0.073 0.552,0.271 0.427,0.198 10 false *a

Disconnect the transmission wire connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C171-17 (NTB) - Body ground Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C171-18 (NTO) - Body ground Always 99 to 101 Ω



Text in Illustration
*a Front view of wire harness connector
(to Transmission Wire)


OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))
a.
C206606E05
1.012,2.91 1.435,3.112 0.423,0.202 10 NTO 1.213,2.886 1.432,2.365 false 1.767,2.886 1.548,2.365 false 1.578,2.91 2.002,3.112 0.423,0.202 10 NTB 0.13,0.078 0.554,0.280 0.423,0.202 10 *a 0.13,1.679 0.554,1.881 0.423,0.202 10 *b 1.373,1.209 1.796,1.411 0.423,0.202 10 1 1.469,1.184 1.688,0.809 false 2.129,1.184 1.91,0.809 false 2.118,1.209 2.541,1.411 0.423,0.202 10 2

Disconnect the transmission revolution sensor (NT) connector (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>SPEED SENSOR(for Input Revolution Sensor)>REMOVAL).


b.

Disconnect the transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 1 of the transmission revolution sensor (NT) connector - 17 (NTB) Always Below 1 Ω
Terminal 2 of the transmission revolution sensor (NT) connector - 18 (NTO) Always Below 1 Ω
Terminal 1 of the transmission revolution sensor (NT) connector or 17 (NTB) - Body ground Always 10 kΩ or higher
Terminal 2 of the transmission revolution sensor (NT) connector or 18 (NTO) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Revolution Sensor (NT))
*b Component without harness connected
(Transmission Wire)



OK

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
a.

Disconnect the C171 transmission wire connector.


b.

Disconnect the A81 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C171-17 (NTB) - A81-7 (NTB) Always Below 1 Ω
C171-18 (NTO) - A81-8 (NTO) Always Below 1 Ω
C171-17 (NTB) or A81-7 (NTB) - Body ground Always 10 kΩ or higher
C171-18 (NTO) or A81-8 (NTO) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR