Home › Drivetrain › CLUTCH › CLUTCH UNIT(for 1GR-FE)
RM2660E _52 Drivetrain _052808 CLUTCH _0255316 CLUTCH UNIT(for 1GR-FE) A

CLUTCH  CLUTCH UNIT(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C358754E01
2.594,1.135 2.667,0.875 2.667,0.875 2.792,0.865 false 0.927,2.938 1.906,3.156 0.979,0.219 10 false Flywheel Side 2.865,0.781 3.323,0.979 0.458,0.198 10 false SST

a.

Insert SST into the clutch disc, then insert the clutch disc into the flywheel.

SST
09301-00110  

NOTICE:

Take care not to insert the clutch disc in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

C173307E02
1.26,1.417 0.885,1.198 true 0.896,1.208 1.198,1.458 true 2.531,1.271 2.729,0.927 false 2.74,0.927 2.875,0.927 false 0.198,1.031 0.99,1.219 0.792,0.188 10 false Matchmark 1.823,0.063 2.156,0.219 0.333,0.156 10 false 1, 4 2.458,0.958 2.594,1.115 0.135,0.156 10 false 2 0.99,1.823 1.125,1.979 0.135,0.156 10 false 3 2.469,0.302 2.604,0.458 0.135,0.156 10 false 5 1.875,1.948 2.01,2.104 0.135,0.156 10 false 6 0.917,0.781 1.052,0.938 0.135,0.156 10 false 7 2.948,0.844 3.25,1.052 0.302,0.208 10 false SST

a.

Align the matchmark on the clutch cover with the one on the flywheel.


b.

In the order shown in the illustration, temporarily install the 6 bolts starting from the bolt located near the knock pin on the top.


c.

Check that the disc is in the center by lightly moving SST up and down, and left and right.

SST
09301-00110  


d.

Evenly tighten the bolts by following the order shown in the illustration.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

C173308

a.

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum Misalignment:

1.3 mm (0.0512 in.)



b.
C173309E01
2.863,0.644 3.181,0.834 0.318,0.191 10 SST 2.333,0.952 2.627,0.723 false 2.627,0.723 2.816,0.723 false

If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

SST
09333-00013  


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

U164588E02
0.344,1.865 1.688,2.094 1.344,0.229 10 true Release hub grease

a.

Apply release hub grease to the release fork, release bearing, push rod contact point and pivot points shown in the illustration.

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.
U164727E02
0.385,1.896 1.729,2.135 1.344,0.24 10 true Clutch spline grease

Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



c.
C163036

Install the release bearing to the clutch release fork with the clip.


d.
C173304

Install the release fork support to the transmission unit.

Torque:
47 N*m (480 kgf*cm, 35 ft.*lbf)


e.

Install the clutch release fork with the clutch release bearing to the transmission unit.

HINT:

After installation, move the fork back and forth to check that the release bearing slides smoothly.



Hide 5.INSTALL MANUAL TRANSMISSION ASSEMBLY